• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.74-77
• /
• 2017

In this work, we investigated the etching characteristics of TaNO thin films and the selectivity of TaNO to $SiO_2$ in an $O_2$/CF4/Ar inductively coupled plasma (ICP) system. The maximum etch rate of TaNO thin film was 297.1 nm/min at a gas mixing ratio of O2/CF4/Ar (6:16:4 sccm). At the same time, the etch rate was measured as a function of the etching parameters, such as the RF power, DC-bias voltage, and process pressure. X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment, as well as the accumulation of low volatile reaction products on the etched surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the $CF_4$-containing plasmas.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.67-70
• /
• 2001

$SrBi_2Ta_2O_9$ thin films were etched at high-density $Cl_2/CF_4/Ar$ in inductively coupled plasma system. The chemical reactions on the etched surface were studied with x-ray photoelectron spectroscopy and secondary ion mass spectrometry. The etching of SBT thin films in $Cl_2/CF_4/Ar$ were chemically assisted reactive ion etching. The maximum etch rate was 1060 Am /min in $Cl_2$(20)/CF_4(20)/Ar(80). The small addition of $Cl_2$ into $CF_4$(20)/Ar(80) plasma will decrease the fluorine radicals and the increase CI radical. The etch profile of SBT thin films in $Cl_2/CF_4/Ar$ plasma is steeper than in $CF_4$/Ar plasma.Ā저會Ā저ﶖ⨀⡌ឫഀĀ᐀會Ā᐀㡆ﶖ⨀쁌ឫഀĀ᐀會Ā᐀遆ﶖ⨀郞ග堂瀀ꀏ會Āﶖ⨀〲岒ऀĀ᐀會Ā᐀䁇ﶖ⨀젲岒Ā㰀會Ā㰀顇ﶖ⨀끩Ā㈀會Ā㈀ﶖ⨀䡪Ā᐀會Ā᐀䡈ﶖ⨀Ā᐀會Ā᐀ꁈﶖ⨀硫Ā저會Ā저ﶖ⨀샟ගကĀ저會Ā저偉ﶖ⨀栰岒ఀĀ저會Ā저ꡉﶖ⨀1岒Ā저會Ā저Jﶖ⨀惝ග؀Ā؀會Ā؀塊ﶖ⨀ග㼀Ā切會Ā切끊ﶖ⨀⣟ගఀĀ搀會Ā搀ࡋﶖ⨀큭킢Ā저會Ā저

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.426-428
• /
• 1989

As a first phase of plasma study intended for semiconductor processing research, we have studied the discharge phenomena. In particular, we have obtained a specific formula for the breakdown voltage as a function of the neutral state pressure of reactive gases. Our experimental results with H2,O2,Ar,CF4 seem ro verify this formula. In addition we find the voltage levels for various gases in the descending order of CF4>O2=Ar>H2 in high pressure region, while H2>CF4>O2>Ar in low pressure region. When H2 and CF4 were mixed, we observe the overall voltage dominated by the gas with lower breakdown volotage.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.11a
• /
• pp.150-150
• /
• 1996

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.21-25
• /
• 2001

In this study, recovery of plasma etching· damage in PZT thin film with additive gas and re-annealing after etching have been investigated. The PZT thin films were etched as a function of $Cl_2/CF_4$ with addition of Ar and $O_2$ with inductively induced plasma. The etch rates of PZT thin films were 1450 $\AA$/min at 30% additive Ar into $(Cl_2(80%)+CF_4 (20%))$ and 1100 $\AA$/min at 10% additive $O_2$ into $C(Cl_2(80%)+CF_4(20%))$. In order to recovery properties of PZT thin films after etching, the etched PZT thin films were re-annealed at various temperatures in at $O_2$ atmosphere. From the hysteresis curves, ferroelectrical properties are improved by $O_2$ re-annealing process. The improvement of ferroelectric behavior at annealed sample is consistent with the increase of the (100) and (200) PZT peaks revealed by x-ray diffraction (XRD). From x-ray photoelectron spectroscopy (XPS) analysis, intensity of Pb-O, Zr-O and Ti-O peak are increased and the chemical residue peak is reduced by $O_2$ re-annealing. The ferroelectric behavior consistent with the dielectric nature of $Ti_xO_y$ is recovered by $O_2$ recombination during rapid thermal annealing process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.21-25
• /
• 2001

In this study, recovery of plasma etching damage in PZT thin film with additive gas and re-annealing after etching have been investigated. The PZT thin films were etched as a function of Cl$_2$/CF$_4$ with addition of Ar and $O_2$ with inductively induced plasma. The etch rates of PZT thin films were 1450$\AA$/min at 30% additive Ar into (Cl$_2$(80%)+CF$_4$ (20%)) and 1100$\AA$/min at 10% additive $O_2$ into C(Cl$_2$(80%)+CF$_4$ (20%)). In order to recovery properties of PZT thin films after etching, the etched PZT thin films were re-annealed at various temperatures in at $O_2$ atmosphere. From the hysteresis curves, ferroelectrical properties are improved by $O_2$ re-annealing process. The improvement of ferroelectric behavior at annealed sample is consistent with the increase of the (100) and (200) PZT peaks revealed by x-ray diffraction (XRD). From x-ray photoelectron spectroscopy (XPS) analysis, intensity of Pb-O, Zr-O and Ti-O peak are increased and the chemical residue peak is reduced by $O_2$ re-annealing. The ferroelectric behavior consistent with the dielectric nature of Ti$_{x}$O$_{y}$ is recovered by $O_2$ recombination during rapid thermal annealing process.s.s.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1399-1401
• /
• 2009

In this article, we reported the results of etching polymonochloro-para-xylylene (parylene-C) thin films using inductively coupled plasma and $CF_4/O_2$ gas mixture. The $CF_4$ gas fraction increased up to the approximately 16 %, the polymer etch rate increased in the range of 277 - 373 nm/min. It confirmed that the etch rate of the parylene-C mainly depended on the O radical density in the plasma. Using a contact angle measurement, the contact angle increased with increasing the $CF_4$ fraction. Moreover, the contact angle was highly related a $CF_x$ functional group on parylene films.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1504-1507
• /
• 2009

In this paper, the etching behavior of ZnO in $CF_4$ plasma mixed Ar was investigated. Previously, the etch rate in $CF_4$/Ar plasma was reported that it is slower than that in Cl containing plasma. But, plasma included Cl atom can produce the by-product such as $ZnCl_2$. In order to solve this film contamination, no Cl containing etching gas is required. We controlled the etching parameter such as source power, substrate bias power, and $CF_4$/Ar gas ratio to acquire the fast etch rate using a ICP etcher. We accomplished the etching rate of 144.85 nm/min with the substrate bias power of 200W. As the energetic fluorine atoms were bonded with Zinc atoms, the fluoride zinc crystal ($ZnF_2$) was observed by X-ray photoelectron spectroscopy (XPS).

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.1
• /
• pp.32-36
• /
• 2014

In this study, the etching characteristics of titanium dioxide ($TiO_2$) thin films were investigated with the addition of $N_2$ to CF4/Ar plasma. The crystal structure of the $TiO_2$ was amorphous. A maximum etch rate of 111.7 nm/min and selectivity of 0.37 were obtained in an $N_2/CF_4/Ar$ (= 6:16:4 sccm) gas mixture. The RF power was maintained at 700 W, the DC-bias voltage was - 150 V, and the process pressure was 2 Pa. In addition, the etch rate was measured as functions of the etching parameters, such as the gas mixture, RF power, DC-bias voltage, and process pressure. We used X-ray photoelectron spectroscopy to investigate the chemical state on the surface of the etched $TiO_2$ thin films. To determine the re-deposition and reorganization of residues on the surface, atomic force microscopy was used to examine the surface morphology and roughness of $TiO_2$ thin films.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.255-258
• /
• 2002

In this study, $CeO_2$thin films were etched with an addition of $Cl_2$gas to $Ar/CF_4$gas mixing in an inductively coupled plasma(ICP) etcher. The surface reactions of the etched $_CeO2$thin films were investigated by X-ray photoelectron spectroscopy(XPS). It was analyzed that Ce peaks were mainly observed in Ce-O bonds formed $CeO_2$or $CeO_3$compounds. Cl peaks were detected by the peaks of Cl $2p_{3/2}$ and Cl $2p_{1/2}$. Almost all of Cl atoms were combined with Ce atoms like $CeCl_{x}$ compounds.