• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.3 no.2
• /
• pp.125-130
• /
• 1993

We has made 2-zone vertical electric furnace and has been grown CdS single crystal by sublimation method in crystal growth tube with tail tube without seed crystal for growth. While it has been growing, temperature difference ${\Delta}T$ of source and growth part has nearly agreed with theoritical value $14.7^{\circ}C$and experimental value $15^{\circ}C$ Then, crystal of best quality has been grown, when temperature of tail tube has been $110^{\circ}C$, in spite of quickly pulling up crystal growth tube a degree O.38mm per hour. The grown crystal have had hexagonal structure and single crystal with c-axis to length of crystal growth tube from X- ray diffraction pattern of powder method and Laue pattern of back reflection Laue method. Also, the mobility and carrier density from Hall effect measurement have been $316cm^2/V{\cdot}sec$ and $2.90{\times}10^{16}cm^{-3}$ at the room temperature, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.05a
• /
• pp.559-562
• /
• 2017

In city, tracing of power transmission lines is difficult due to compound installation of overhead and underground lines, transposition, bad view caused by trees or big buildings. It is hard problem for electrical technician on site to trace power transformers or power lines to serve customers in 3 phase -4 wires power distribution systems. It is necessary that the correct and fast tracing method is required for load balancing among distribution lines. Old technology use to trace off-lines with high power impulse injection. Our proposed method use to trace live lines with very small power high frequency signal injection. Typical power transformers in the distribution system prevent propagating the higher frequency carrier signal. The proposed method uses the limited propagation ability to identify the power transformer to serve customers. Two end communication terminals are required to be synchronized between them for determination on electrically same phases. Challenging issue is to achieve synchronization without GPS providing synchronizing time. A novel power transformer and wire identification system is designed and implemented. The system consists of a transmitter and a receiver with power-line communication module. Some experiments are conducted to verify the theoretical concepts in a big commercial building. Also some simulations are done to help and understand the concepts by using MATLAB Simulink simulator.

• 전기의세계
• /
• v.28 no.4
• /
• pp.53-63
• /
• 1979

Interface recombination velocity in $Al_{x}$G $a_{1-x}$ As-GaAs and $Al_{0.85}$, G $a_{0.15}$ As-GaA $s_{1-y}$S $b_{y}$ heterojunction systems is studied as a function of lattice mismatch. The results are applied to the design of highly efficient III-V heterojunction solar cells. A horizontal liquid-phase epitaxial growth system was used to prepare p-p-p and p-p-n $Al_{x}$G $a_{1-x}$ As-GaA $s_{1-y}$S $b_{y}$-A $l_{x}$G $a_{1-x}$ As double heterojunction test samples with specified values of x and y. Samples were grown at each composition, with different GaAs and GaAs Sb layer thicknesses. A method was developed to obtain the lattice mismatch and lattice constants in mixed single crystals grown on (100) and (111)B oriented GaAs substrates. In the AlGaAs system, elastic lattice deformation with effective Poisson ratios .mu.$_{eff}$ (100=0.312 and .mu.$_{eff}$ (111B) =0.190 was observed. The lattice constant $a_{0}$ (A $l_{x}$G $a_{1-x}$ As)=5.6532+0.0084x.angs. was obtained at 300K which is in good Agreement with Vegard's law. In the GaAsSb system, although elastic lattice deformation was observed in (111) B-oriented crystals, misfit dislocations reduced the Poisson ratio to zero in (100)-oriented samples. When $a_{0}$ (GaSb)=6.0959 .angs. was assumed at 300K, both (100) and (111)B oriented GaAsSb layers deviated only slightly from Vegard's law. Both (100) and (111)B zero-mismatch $Al_{0.85}$ G $a_{0.15}$As-GaA $s_{1-y}$S $b_{y}$ layers were grown from melts with a weight ratio of $W_{sb}$ / $W_{Ga}$ =0.13 and a growth temperature of 840 to 820 .deg.C. The corresponding Sb compositions were y=0.015 and 0.024 on (100) and (111)B orientations, respectively. This occurs because of a fortuitous in the Sb distribution coefficient with orientation. Interface recombination velocity was estimated from the dependence of the effective minority carrier lifetime on double-heterojunction spacing, using either optical phase-shift or electroluminescence timedecay techniques. The recombination velocity at a (100) interface was reduced from (2 to 3)*10$^{4}$ for y=0 to (6 to 7)*10$^{3}$ cm/sec for lattice-matched $Al_{0.85}$G $a_{0.15}$As-GaA $s_{0.985}$S $b_{0.015}$ Although this reduction is slightly less than that expected from the exponential relationship between interface recombination velocity and lattice mismatch as found in the AlGaAs-GaAs system, solar cells constructed from such a combination of materials should have an excellent spectral response to photons with energies over the full range from 1.4 to 2.6 eV. Similar measurements on a (111) B oriented lattice-matched heterojunction produced some-what larger interface recombination velocities.ities.ities.s.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.6C
• /
• pp.502-511
• /
• 2012

As the importance of GNSS system increases, the necessity of independent system is increased also. When the independent GNSS system is required, GNSS signal design is necessary with requirement definition. This paper suggests the design method of GNSS signal using the analysis result of receiver performance. First, the candidates are defined based on the design elements. Then the receiver performance of the candidates is analyzed based on the performance evaluation parameters. The weights of performance evaluation parameter are defined in order to consider the receiver performance in a various aspects. Finally, the calculation of normalized performance evaluation parameters and weights are derived to obtain the compared value for signal selection. Spreading code, modulation method and carrier frequency are considered as design parameters. Also, correlation width, DLL PLL thermal noise jitter, frequency bandwidth and side lobe peak ratio are considered as performance evaluation parameters. And positioning performance, robustness to noise, bandwidth efficiency are considered as the performance aspects. This paper analyzes the performance of each candidate using software based simulator and suggest the method to compare objectively the performance of each candidates.

• The KIPS Transactions:PartD
• /
• v.15D no.6
• /
• pp.861-872
• /
• 2008

As rapid development of computing environment, field of automatic identification research which interoperates with various physical objects and digital information is making active progress. Although the automatic identification system is widely used in various industries, application of automatic identification system in the field of medical health doesn't reach other industry. Therefore research in medical health supplies such as medical equipment, blood, human tissues and etc is on progress. This paper suggests the application of automatic identification technology for biological resources which is core research material in human genome research. First of all, user environment requirements for the introduction of automatic identification technology are defined and through the experiments and research, barcode is selected as a suitable tag interface. Data Matrix which is 2D barcode symbology is chosen and data schema is designed based on UCC/EAN-128 for international defecto standard. To showapplicability of proposed method when applied to actual environment, we developed, tested and evaluated application as following methods. Experiments of barcode read time at 196 and 75 below zero which is actual temperature where biological resources are preserved resulted read speed of average of 1.6 second and the data schema satisfies requirements for the biological resources application. Therefore suggested method can provide data reliability as well as rapid input of data in biological resources information processing.

• Journal of the Korean Chemical Society
• /
• v.48 no.6
• /
• pp.553-560
• /
• 2004

In this experiment, a three dimensional structure analysis was carried out to examine the surface defects of semiconductor made artificially on known scale. It was investigated the three dimensional imaging according to the sample depth and the thermal diffusivity as well as the carrier transport properties. The thermal diffusivity measurement of the intrinsic GaAs semiconductor was also analyzed by the difference of frequency-dependence photoacoustic signals from the sample surface of different conditions. Thermal properties such as thermal diffusion length or thermal diffusivity of the Si wafer with and without defects on the surface were obtained by interpreting the frequency dependence of the PA signals. As a result, the photoacoustic signal is found to have the dependency on the shape and depth of the defects so that their structure of the defects can be analyzed. This method demonstrates the possibility of the application to the detection of the defects, cracks, and shortage of circuits on surface or sub-surface of the semiconductors and ceramic materials as a nondestructive testing(NDT) and a nondestructive evaluation(NDE) technique.

• Journal of the East Asian Society of Dietary Life
• /
• v.22 no.1
• /
• pp.88-94
• /
• 2012

Histamine is a kind of primary biogenic amine arising from the decarboxylation of the amino acid L-histidine. The toxicology of histamine and its occurrence and formation in foods are especially emphasized in fermented foods. In this study, the biosensor for detection of histamine with functionalized multi-walled carbon nanotubes (MWCNT) was developed. We also searched for an appropriate insoluble substrate to immobilize the enzyme. The developed biosensor showed a detection limit of $0.1{\mu}M$ hydrogen peroxide. The enzyme reactor was prepared with diamine oxidase immobilized on insoluble carriers including CNBr-activated sepharose 4B, calcium alginate, and controlled pore size glass beads. The coupling efficiency of CNBr-activated sepharose 4B, calcium alginate, and controlled pore size glass beads were 48.5%, 40.3%, and 51.0%, respectively. In addition, the response currents on histamine with each immobilized enzyme reactor prepared with CNBr-activated sepharose 4B, calcium alginate, and controlled pore size glass beads were 120 nA, 110 nA, and 140 nA at $100{\mu}M$ of histamine concentration, respectively. Therefore, it is suggested that controlled pore size glass beads are the best carriers for immobilizing diamine oxidase to detect histamine in this biosensor.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.1
• /
• pp.9-16
• /
• 2017

As a preliminary study of enter or leaving traffic patterns of the Korea main port, port Management Information System (Port-MIS) data was used to check the volume of vessels entering and leaving the port of Busan, and three consecutive days from each seasons were selected for study. Selected 12-day General Information Center on Maritime Safety & Security (GICOMS) data was also used to analyze the traffic pattern in the main traffic lane of Busan port for dangerous goods carrier. Also, the distance between dangerous goods carriers and Oryukdo breakwater of east breakwater in the main traffic lane was analyzed. Collision probability was estimated using the cumulative probability distribution function of the normal distribution for the maritime traffic safety audit scheme based on the assumption that a ship's trajectory has a normal distribution for a section of the route. However, in case of entry or leaving thorough the Oryukdo breakwater and entry thorough the east breakwater, ship's sailing trajectories were revealed not to follow a normal distribution via regularity testing using a KS-test and SW-test. Especially in the north port, the tendency of the right side of the ship to pass was remarkable. It is desirable to develop a traffic model suitable for the characteristics of the port rather than to apply general traffic theories, and to apply this model to a maritime traffic safety diagnosis, so further research is needed.

• Journal of Korea Port Economic Association
• /
• v.27 no.2
• /
• pp.313-331
• /
• 2011

Due to have been more keen in East-North Asia Hub Port competition, to be accelerated Busan New Port development, and to result to supply excess position, Busan port has been confronted by many problems. Also, as facilities of North Port is old, it is impossible to secure 16m depth of water at North Port, and North Port redevelopment is being, container traffic of North Port is accelerated to shift at New Port. Therefore, it. is time to seek for connection growth plan of succeeding together-Busan North & New Port as soon as possible. Connection growth plan of succeeding together-Busan North & New Port is focused, as follows. First, it is required to set up model for connection growth plan of succeeding together-Busan North & New Port. It is valid to specialize for ULCC, to promote to global port at New Port, and it is effective to focus on feeder service and general cargo handling, and to include most space to North Port redevelopment. Second, through port function reorganization, it is required to create a synergy by port function clustering. Third, through effective connection traffic network expansion for moving T/S cargo effectively, it is required to develop Busan Port for T/S cargo-focused port. Fourth, it is required to develop port hinterland logistics zone for creating container traffic through connection development of New Port-BJFEZ. Finally, it is required to build SCM system for creating container traffic among shipper, carrier, freight forwarder and related institution.