• Journal of the Korean Ceramic Society
• /
• v.33 no.7
• /
• pp.809-815
• /
• 1996

When Li2O.2SiO2 glass was crystallized between the temperature of maximum nucleation and the temperature of maximum crystal growth it was found that the control of heating rate had serious effect on the crystallinity and microstructure and the greatly changed physical properties. Density and elastic modulus tends to increase but thermal expansion coefficient decreased with increased crystallinity. When heating rate between the tempe-rature of maximum nucleation and the temperature of maximum crystal growth was 10~5$0^{\circ}C$/hr. crystallinity was increased to result in the increment of strength. When nuclation was done at 44$0^{\circ}C$ for 5 hours and the temperature of crystal growth was held at 575$^{\circ}C$ strength was increased until crystallinity reached 65% and strength was decreased with higher crystallinity. These phenomena could be explained that even for the same crystallinity different heat rates resulted in different number and size of cracks.

• Journal of the Korean institute of surface engineering
• /
• v.23 no.4
• /
• pp.208-217
• /
• 1990

Electroless Ni-Cu-P plating was performed was performed to investigate for plating and changes in microhardness and corrosion rate of of electroless deposits depending on heat treatment. The activation energy for $75~85^{\circ}C$ were calculated to be 66.7KJ/mole. Plating rate increased to 34% with addition of 200ppm of NaF and 0.8ppm of thiourea to the bath. The highest hardness value was obtained by heat treatment deposits layer at$ 400^{\circ}C$, 1 hour. The increase in hardness of deposits by heating was confirmed to be associated with crystallization of the amorphous deposits. Corrosion resistance of deposir layer, which had been heated up to $300^{\circ}C$, was found to be exellent when immersed in 1N-H2SO4 solution, Change of the corrosion resistance seems to have some important bearing on content of amorpous, Ni3P and Cu3P.

• Journal of Communications and Networks
• /
• v.4 no.3
• /
• pp.199-208
• /
• 2002

The downlink rate scheduling problem is considered for CDMA networks with multiple users carrying packets of heterogeneous traffic (voice/audio only, bursty data only or mixed traffic), with each type having its own distinct quality of service requirements. Several rate scheduling algorithms are developed, the common factor of which is that part of the decision on which users to serve is based on a function of the deadline of their head-ofline packets. An approach of Andrews et al., in which the basic Earliest-Deadline-First algorithm is studied for similar systems, is extended to result in better performance by considering a more efficient power usage and by allowing service of more than one user per timeslot if the power resources permit it. Finally, the performance of the proposed schemes is compared through simulations.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.350-357
• /
• 2019

We analyzed the system efficiency of small solar power plants with 80% of total solar power plants. The data of the solar power plant with installed capacity of 100kW was collected and the correlation of the ESS efficiency according to the capacity of the PCS and the battery of each power plant was deduced. As a result, the higher the C-rate value affecting the discharge rate of the battery, The discharge efficiency of the plasma display panel is increased.

• Korean Journal of Environmental Biology
• /
• v.26 no.4
• /
• pp.323-329
• /
• 2008

The feeding, clearance rate, ingestion rate and body composition of Jicon scallop, Chlamys farreri was investigated under combination in water temperature (24, 27, 30$^{\circ}C$) with salinity (24, 27, 30 %o). The Maximum feeding, Clearance rate showed 8.88 L h$^{-1}$ g$^{-1}$ and 25.42 $\times$ 10$^7$ cells h$^{-1}$ g$^{-1}$ under the experiment condition of 24$^{\circ}C$ and 30%o. While, the minimum feeding, clearance rate and ingestion rate were 0.15 L h$^{-1}$ g$^{-1}$ and 0.73 $\times$ 10$^7$ cells h$^{-1}$ g$^{-1}$ under the experiment condition of 30$^{\circ}C$ and 24%o, respectively. It was indicated that body composition of C. farreri were affected by water temperature and salinity.

• Journal of Aquaculture
• /
• v.12 no.3
• /
• pp.213-220
• /
• 1999

This study was performed to investigate the effects of water temperature and stocking density and rotifer density on the mass production of larval red marbled rockfish, Sebastiscus tertius. Total length of the marbled rockfish larva grown in $23^{\circ}C$ of water temperature were 10.80mm, which was the best, while those grown in $29^{\circ}C$ of water temperature were 6.28mm, which was the lowest. The survival rates of red marbled rockfish larvae grown in $20^{\circ}C$ and $23^{\circ}C$ were 24.0% and 18.5%, respectively. However, the survival rate of red marbled rockfish larvae grown in $26^{\circ}C$ was $7^{\circ}C$ and no larvae survived in $29^{\circ}C$. The total length of red marvled rockfish larva stocked at the density of 5 and 10 larvaper liter of water were high, which were 11.52 mm and 11.22 mm, respectively, but those stocked at the density of 30 larva per liter of water were 7.55mm, which was the lowest. The survival rate of red marbled rockfish larva stocked at the density of 2.5 larva per liter of water was 52.0%, which was the best, but the lowest, 18.0% for the red marbled rockfish larva stocked at the density of 30 larva per liter. There was a trend toward decrease in survival rate of red marbled rockfish larva as their stocking density increased. The survival rates of red marbled rockfish larva fed rotifers at the density of 10 and 5 individuals per ml were high, 48.5% and 48.0%, and their total lengths were 11.92 and 11.89mm, respectively, which grew relatively fast. The survival rate and the total length of red marbled rockfish larva fed rotifers at the density of 30 individuals per ml were the lowest, which were 8.40mm and 21.5%, respectively. Also, red marbled rockfish larva fed rotifers at the density of more than 20 individuals per ml achieved poor survival and growth. These results indicated that the proper conditions for the mass production of larval red marbled rockfish were $23^{\circ}C$ of water temperature, fish larva stocking density of 5 to 10 larva per liter of water and rotifers density of 5 to 10 individuals per ml as live feed.

• Membrane Journal
• /
• v.5 no.4
• /
• pp.137-144
• /
• 1995

This studies concern the separation of aqueous boric acid solution and same solution containing silica using cellulose acetate RO S/W 4040 module manufactured by Hydranautics Co. The operating conditions of the applied pressures, temperatures, and feed flow rate are also investigated to characterize the permeabilities, biroc acid recovery, and silica rejection, so that the optimum operating conditions would be found out. In the case where the operating conditions are the temperature 35$^{\circ}$C, The pressure 20atm, and the feed flow rate 2.82 l/min, for the boric acid aqueous solution, the boric acid recovery 58.7% and the permeation rate 2.82 l/min were obtained. And also the results showed the boric acid recovery 68.1% and the permeation rate 1.56 l/min at the operating conditions, 35$^{\circ}$C and 10atm. For the boric acid solution containing silica, when the feed solution are at the conditions of 35$^{\circ}$C and 3.2atm, the boric acid recovery 69.7%, the silica rejection 97.5% and the permeation rate 0.47 l/min were obtained. And the operating conditions were at 35$^{\circ}$C, 20atm and the feed flow rate 2.92 l/min, the results showed the boric acid recovery 56.4%, the silica rejection 96.1% and the permeation rate 2.72 l/min.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.11 s.254
• /
• pp.1494-1501
• /
• 2006

Mechanical and physical properties of a copper alloy for a liquid rocket engine(LRE) combustion chamber liner application were tested at various temperatures. All test specimens were heat treated with the condition they might experience during actual fabrication process of the LRE combustion chamber. Physical properties measured include thermal conductivity, specific heat and thermal expansion data. Uniaxial tension tests were preformed to get mechanical properties at several temperatures ranging from room temperature to 600$^{\circ}C$. The result demonstrated that yield stress and ultimate tensile stress of the copper alloy decreases considerably and strain hardening increases as the result of the heat treatment. Since the LRE combustion chamber operates at higher temperature over 400$^{\circ}C$, the copper alloy can exhibit time-dependent behavior. Strain rate, creep and stress relaxation tests were performed to check the time-dependent behavior of the copper alloy. Strain rate tests revealed that strain rate effect is negligible up to 400$^{\circ}C$ while stress-strain curve is changed at 500$^{\circ}C$ as the strain rate is changed. Creep tests were conducted at 250$^{\circ}C$ and 500$^{\circ}C$ and the secondary creep rate was found to be very small at both temperatures implying that creep effect is negligible for the combustion chamber liner because its operating time is quite short.

• Korean Journal of Environment and Ecology
• /
• v.12 no.1
• /
• pp.9-13
• /
• 1998

Because Lysimachia mauritiana is not able to maintain the seed viablity for a long time, it has difficulties in using for the ornamental plants or landscape gardening. This study was conducted to elucidate the optimal germination conditions of Lysimachia mauritiana seeds. The germination rate of the seeds was higer in light condition than in dark one. In experment determining the proper germination temperature, the germination rates were 2.2%, 96.9% and 91.2% under 35$\circ $C, 25$\circ $C, and 20$\circ $C, respectively in light condition. The approprate temperature for the germination was 25$\circ $C in light. The decreases of germination rate with the increase of the preservation periods was able to recover by priming pretreated with NaCl solution and KNO$_{3}$ + K$_{3}$H$_{2}$PO mixed solutions. When the storage period was 300 days, the germination rate was 75% without priming treatments. But the seeds primed with NaCl 0.1M and KNO$_{3}$ + K$_{3}$H$_{2}$PO mixed solutions 0.1M, showed germination rate above 90%. T$_{50}$ also was shorten from 5.25 without priming to 3.78 with NaCl 0.1M. Seed priming may induce earlier sprouts and increase germination rate of long-preserved seeds of native wild plants.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.1
• /
• pp.47-54
• /
• 2002

This paper presents the results of an experimental investigation on the combustion of single droplets and 1-D droplet arrays of jet A-1 fuel droplets in atmospheric pressure. Experimental results indicate that burning rate constants$({\kappa}_c)$ of jet A-1 fuel droplets were independent of initial droplet size as $0.915{mm}^2$/sec. It was acquired a general relationship expressing the variation of $d^2$ with time for droplet burning For 1-D droplet arrays $(l/d_o$=1.208{\sim}2.922)$/TEX>, the burning rate constant ${\kappa}_c$ decreased with decreasing droplet spacing $l/d_o$ and, The effect on combustion rate constant ${\kappa}_c$ was stronger to second fuel droplet than third fuel droplet with uniform droplet distance