• Journal of the Korean Society of Industry Convergence
• /
• v.16 no.1
• /
• pp.21-26
• /
• 2013

Burned gas of methane-air mixtures with water vapor have been analysed to study the exhaust emission using gas-chromatography and computation. The computations were carried out for the gas analysis using premix code of Chemkin program to compare the experimental results. The quantity of water vapor contained were changed 5% and 10% of total mixtures, and equivalence ratio of mixtures between 0.6 and 1.2 were tested under the ambient temperature 323K and 373K. The results showed CO, $CO_2$ decreased and $H_2$ increased by increasing the water contents. The CO increased and $CO_2$ decreased by increasing the ambient temperature. The $CO_2$ shows the maximum product at equivalence ratio 1.0, in otherwise the $CH_4$ produced the minimum values in the same range. The results showed little difference between these two methods.

• Proceedings of KOSOMES biannual meeting
• /
• 2017.11a
• /
• pp.69-69
• /
• 2017

Flame arrestor as end of line flame arrester for endurance burning prevents a light-back at deflagration and stabilized burning (during and after endurance burning) of potentially explosive vapor-air and gas-air mixtures at the end of vent pipes. In a flame arrestor, spring is an important part. The spring load as well as the spring's elasticity determine when the hood is opened. In addition, the spring have to work in high temperature condition due to gas burning. Therefore, it is necessary to analyze mechanical load and elasticity of spring when gas is burned. Based on the dynamic calculation on working process of a specific flame arrestor, analysis of spring is taken. A three dimensional model for spring burned in flame arrestor by using CFD simulation. Results of the CFD analysis are input in FEM simulation to analyze structure of the spring. The simulation results can predict and estimate the spring's load and elasticity at variation of the spring's deflection. Moreover, the obtained result can provide makers with references to optimize design of spring as well as flame arrestor.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2000.04a
• /
• pp.229-235
• /
• 2000

A study on the improvement of anti-abrasion nature of curved ducts for high-velocity gas-solid flow which are typically equipped in a coal-burned steam power plant has been investigated numerically and experimentally. To reduced the abrasion of pipe by particle, we have tried to form the vortex flow field in the region where flow changes its direction , modelled with two different shapes. 22.5$^{\circ}$and 90$^{\circ}$ elbows. the governing equations for three -dimensional , turbulent flow fields are discretized by FVM and solved bySIMPLE algorithm . From the numerical analysis, the new designed elbows for reducing abrasion have been developed. Numerical results are compared with the experimental abrasion data which are obtained from one of the operating coal burned steam power plants in Korea. Comparison of these results show that the developed elbows have much more durability than the original one.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.4
• /
• pp.56-62
• /
• 2008

A synthetic gas reformed from hydrocarbon-based fuels consists of $H_2$, CO and $N_2$. Hydrogen contained in the synthetic gas is a very useful species in chemical processes, due to its wide flammability range and fast burning speed. The ESGI (Exhaust Synthetic Gas Injection) technology is developed to shorten the light-off time of three way catalysts through combustion of the synthetic gas in the exhaust manifold during the cold start period of SI engines. Before the ESGI technology is applied to the test engine, the authors set a test rig that consists of gas temperature and composition controllers, an exhaust pulse generator and an exhaust manifold with a visualization window, in order to optimize the point and conditions of injection of the synthetic gas. Through measuring burned gas temperatures and taking photographs of synthetic gas combustion at the outlet of the exhaust manifold, the authors tried to find the optimal injection point and conditions. Analysis of burned gas composition has been performed for various $O_2$ concentrations. As a result, when the synthetic gas is injected at the port outlet of the cylinder No. 4 and $O_2$ concentration exceeds 4%, combustion of the synthetic gas is strong and effective in the exhaust manifold.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.10 no.5
• /
• pp.609-616
• /
• 2018

The cargo handling system, which is composed of a fuel gas supply unit and cargo tank pressure control unit, is the second largest power consumer in a Liquefied Natural Gas (LNG) carrier. Because of recent enhancements in ship efficiency, the surplus boil-off gas that remains after supplying fuel gas for ship propulsion must be reliquefied or burned to regulate the cargo tank pressure. A full or partial liquefaction process can be applied to return the surplus gas to the cargo tank. The purpose of this study is to review the current partial liquefaction process for LNG carriers and develop new processes for reducing power consumption using exergy analysis. The developed partial liquefaction process was also compared with the full liquefaction process applicable to a LNG carrier with a varying boil-off gas composition and varying liquefaction amounts. An exergy analysis showed that the Joule-Thomson valve is the key component needed for improvements to the system, and that the proposed system showed an 8% enhancement relative to the current prevailing system. A comparison of the study results with a partial/full liquefaction process showed that power consumption is strongly affected by the returned liquefied amount.

• Journal of the Korea Safety Management & Science
• /
• v.20 no.3
• /
• pp.21-26
• /
• 2018

This paper describes result of a study on safety against a fire of charging cable for mobile phone for vehicle. Combustion on the USB cable in the car was happened while driving. Gas coming from the burning USB cable could be a reason which can make a secondary car accident since the driver also can be embarrassed while driving. In order to prevent a secondary car accident connected on the road, to research a reason why USB cable can emit gas and be burned in charging. We did simulation test with abnormal fault condition for the electronic component on the board in the USB cable. So we get the result from abnormal fault condition simulation test, for instance, shorted test for output terminal of 8 pin switch, shorted test for chip resistor after thermal aging in the condition $25^{\circ}C$, 93 % RH during 48 hours. To analysis the result of all test, Combustion on the USB cable was not the 8 pin but other electrical component such as a chip resistor. Therefore we guess that the reason for USB cable combustion in charging in a car was not 8 pin and a LED but another defective component.

• Journal of the Korean Society of Combustion
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2013

Authors' previous works on thermoacoustic(TA) model development showed good results in predicting combustion instability characteristics in a gas turbine combustor. However, they also suggested there were some limitations in growth rate estimation, which might be related with over-simplification of flame structure. As a first trial for improving the model accuracy, the current paper introduces the modified TA model considering the actual flame location in the combustor. The combustor is divided into the unburned and the burned area before and after the flame location, and then acoustic equations are re-organized. The modified TA model results show a better accuracy in predicting the growth rate of instabilities comparing with the previous results. However, obtained results still overestimate the conditions where the combustor goes unstable. Further researches considering heat release distribution through flames are required.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.864-870
• /
• 2017

The propellants are burned in the pre-burner of the staged combustion cycle engine, and the resulting hot gas drives the turbine, and the turbine operates the turbo pump. The burned gas passing through the turbo pump is supplied to the combustor at high temperature and high pressure, where the gas is supplied in an excess of fuel or an excess of oxidant depending on the amount of fuel or oxidant. When the cycle works at oxidizer-rich staged combustion, its metal pipe can ignite or explode by the impact of even small particles. In this study, we develop the powder combinations for anti-oxidation coating through the analysis of other coating materials and establish the coating process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.125-131
• /
• 2018

Some propellants in a liquid rocket engine are burned in the pre-burner of a staged combustion cycle engine, resulting hot gas drives the turbine. The burned gas passing through the turbine is supplied to the combustor at high temperature and pressure. The form of the gas can be fuel rich or oxidizer rich dependent upon the mixture ratio or the engine scheme. When the cycle works at oxidizer-rich condition, the metal pipes composing the engine can be ignited or even exploded by an impact of very a small particle. In this study, we developed the powder combination and processes for an anti-oxidation coating through the analysis of various coating materials.

• Journal of the Korean Institute of Gas
• /
• v.17 no.6
• /
• pp.39-45
• /
• 2013

The gas generated from the fire which is continuous until material is completely burned. We can analyze usual gas using chromatography analysis but it can not be applicated to analyze for the gas from the fire because which gas is enormously generated. Besides, chromatography analysis has the disadvantage that it can not continuously analyze the sample's representativness, gas from the fire, Fourier transform infrared spectroscopy, FT-IR, has been utilized for effective combustion gas analysis method in small-scale combustion and on-line analysis has been attempted continuously. However, continuous sampling of 3.5l/min can not be representativness of sample if the gas caused by a massive fire and space. And the gas sampling is practically impossible in such a case. In this study, we attempted remote analysis while overcoming the disadvantages of the current gas analysis by using an Open-Path Infrared Analyzer without pre-treatment of the sampling. For the remote analysis, quantitative analysis method was established regarding each combustion toxic gases. And we measured the gases from the fire that occurs in the real case.