• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.815-819
• /
• 2014

Aluminum nitride (AlN) thin film and TiN film as a buffer layer were deposited on INCONEL 600 substrate by reactive RF magnetron sputtering at room temperature(R.T.) under 25~75% $N_2/Ar$ atmosphere. The as-deposited AlN films at 25~50% $N_2/Ar$ showed a polycrystalline phase of hexagonal AlN, and an amorphous phase. The peak of AlN (002) plane, which was determinant on a performance of piezoelectric transducer, became strong with increasing the $N_2/Ar$ ratio. Any change in the preferential orientation of the as-deposited AlN films was not observed within our $N_2$ concentration range. The piezoelectric sensing properties of AlN module were performed using pressure-voltage measurement system. The output signal voltage of AlN module showed a linear behavior between 20~80 mV in 1~10 MPa range, and the pressure-sensing sensitivity was calculated as 3.6 mV/MPa.

• Journal of Powder Materials
• /
• v.28 no.6
• /
• pp.462-469
• /
• 2021

Tin/graphite composites are prepared as anode materials for Li-ion batteries using a dry ball-milling process. The main experimental variables in this work are the ball milling time (0-8 h) and composition ratio (tin:graphite=5:95, 15:85, and 30:70 w/w) of graphite and tin powder. For comparison, a tin/graphite composite is prepared using wet ball milling. The morphology and structure of the different tin/graphite composites are investigated using X-ray diffraction, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and scanning and transmission electron microscopy. The electrochemical properties of the samples are also examined. The optimal dry ball milling time for the uniform mixing of graphite and tin is 6 h in a graphite-30wt.%Sn sample. The electrode prepared from the composite that is dry-ball-milled for 6 h exhibits the best cycle performance (discharge capacity after 50^th cycle: 308 mAh/g and capacity retention: 46%). The discharge capacity after the 50^th cycle is approximately 112 mAh/g, higher than that when the electrode is composed of only graphite (196 mAh/g after 50^th cycle). This result indicates that it is possible to manufacture a tin/graphite composite anode material that can effectively buffer the volume change that occurs during cycling, even using a simple dry ball-milling process.

• Analytical Science and Technology
• /
• v.36 no.4
• /
• pp.180-190
• /
• 2023

The presence of process related impurities in any drug or the drug product was associated with its safety, stability and efficacy. The overall literature survey proved that there is no method published on the assessment of process related impurities in brigatinib. In this study, a simple, reliable and stable HPLC qualitative method was reported for quantification of process related impurities with easy and quick extraction procedure. The impurities along with standard brigatinib was resolved on Lichrospher^® C18 (250 mm × 4.6 mm; 5 ㎛ particle size) column in room temperature using methanol, acetonitrile, pH 4.5 phosphate buffer in 55:25:20 (v/v) at 1.0 mL/min as mobile phase and UV detection at 261 nm. The method produces well resolved peaks at retention time of 4.60 min, 12.28 min, 3.37 min, 7.34 min and 8.39 min respectively for brigatinib, impurity A, B, C and D. The method produces a very sensitive detection limit of 0.0065 ㎍/mL, 0.0068 ㎍/mL, 0.0053 ㎍/mL and 0.0058 ㎍/mL for impurity A, B, C and D respectively with calibration curve linear in the concentration range of 22.5-135 ㎍/mL for brigatinib and 0.0225-0.135 ㎍/mL for impurities. The method produces all the validation parameters under the acceptable level and doesn't produces any considerable changes in peak area response while minor changes in the developed method conditions. The method can effectively resolve the unknown stress degradation products along with known impurities with less % degradation. The method can efficiently resolve and quantify the impurities in formulation and hence can suitable for the routine quality analysis of brigatinib in raw material and formulation.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.96-99
• /
• 2001

In this paper, we present the simulation results of the multi-layer VCO(Voltage Controlled Oscillator), which is composed of the resonator, the oscillator and the buffer circuit. using EM simulator and nonlinear RF circuit simulator. EM simulator is used for obtaining the EM(Electromagnetic) characteristics of the conductor pattern as well as designing the multi-layer VCO. Obtained EM characteristics were used as real components in nonlinear RF circuit simulation. Finally the overall VCO was simulated using the nonlinear RF circuit simulator. The material for the circuit pattern was Ag and the dielectric was DuPont 951AT, which will be applied for LTCC process. The structure is constructed with 4 conducting layer. Simulated results showed that the output level was about 4.5[dBm], the phase noise was -104[dBc/Hz] at 30[kHz] offset frequency, the harmonics -8dBc, and the control voltage sensitivity of 30[MHz/V] with a DC current consumption of 9.5[mA]. The size of VCO is $6{\times}9{\times}2mm$(0.11[cc]).

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.69.2-69.2
• /
• 2010

Recently, bulk hetero-junction cells have been extensively studied by many researchers. Most of these cells were fabricated by spin coater. However, the spin coating process is not favorable to the large-scaled industry because it is not compatible with roll-to-roll process. One of the alternative methods is Doctor blading. In this study, we fabricated large OPV cells having total area of $100cm^2$. The buffer layer was Poly-(3,4-ethylenedioxythiophene) : poly-(styrenesulfonate) aqueous dispersion (PEDOT:PSS) and the active material is poly (3-hexythiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) blend in the solvent of Chlorobenzene. All of the organic layers were coated by dragging the blade with a speed of 5~20 mm/s on the stage with a temperature of $50^{\circ}C$. As-bladed PEDOT:PSS layer was baked at $120^{\circ}C$ for 10 minutes to eliminate the water. The cell structure is patterned ITO substrate/PEDOT:PSS/P3HT:PCBM/LiF/Al. The topmost electrode, LiF/Al, was deposited by thermal evaporation. After depositing electrode, and the cell was annealed at $150^{\circ}C$ for 30 minutes. The measured ISC, VOC, fill factor, and PCE were 2.95 A, 5.86 V, 0.32, and 0.78%, respectively. PCE was quite low but the large active area could be obtained successfully.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.230-230
• /
• 2012

Graphene have showed promising performance as electrodes of organic devices such as organic transistors, light-emitting diodes, and photovoltaic solar cells. In particular, among various organic materials of graphene-based organic devices, pentacene has been regarded as one of the promising organic material because of its high mobility, chemical stability. In the bottom-contact device configuration generally used as graphene based pentacene devices, the morphology of the organic semiconductors at the interface between a channel and electrode is crucial to efficient charge transport from the electrode to the channel. For the high quality morphology, understanding of initial stages of pentacene growth is essential. In this study, we investigate self-assembly of pentacene molecules on graphene formed on a 6H-SiC (0001) substrate by scanning tunneling microscopy. At sub-monolayer coverage, adsorption of pentacene molecules on epitaxial graphene is affected by $6{\times}6$ pattern originates from the underlying buffer layer. And the orientation of pentacene in the ordered structure is aligned with the zigzag direction of the edge structure of single layer graphene. As coverage increased, intermolecular interactions become stronger than molecule-substrate interaction. As a result, herringbone structures the consequence of higher intermolecular interaction are observed.

• KSBB Journal
• /
• v.15 no.4
• /
• pp.342-345
• /
• 2000

A novel pre-purification method was developed for producing peroxidase to guarantee high purity and yield from plant cell cultures in large-scale process. This method was a simple and efficient procedure for the isolation and pre-purification of peroxidase from the biomass consisting of active clay treatment followed by cationic exchange chromatography. The use of active clay in the pre-purification process allows for rapid and efficient separation of peroxidase from interfering compounds and dramatically increases yield and purity of crude peroxidase for purification steps compared to alternative processes. This pre-purification process serves to minimize the buffer usage size and complexity of the HPLC operations for peroxidase purification. This process is readily scalable to a pilot plant and eventually to a production environment where mass production of material are expected to be produced.

• Food Science and Biotechnology
• /
• v.16 no.3
• /
• pp.444-450
• /
• 2007

The antioxidant activity and isoflavone content of chokong, Rhynchosia nolubilis seeds pickled in vinegar at $4^{\circ}C$ for 2 weeks, were investigated. The polyphenol content and 2,2-diphenyl-1-pycrylhydrazyl (DPPH) radical-scavenging capacity were lower in chokong than in raw seeds. Based on isoflavone analysis, the aglycone (daidzein and genistein) content was high in chokong while the content of the corresponding glucosides (daidzin and genistin) was similar to that in raw seeds. Thermal processing, in which seeds were heated in vinegar at $121^{\circ}C$ for 20 min, reduced the polyphenol content but did not affect the DPPH radical-scavenging capacity compared to the pickling process. The heated seeds had a 2.6 to 2.7 times higher glucoside content and 51 to 55% lower aglycone content than chokong, depending on the kind of vinegar used. During pickling and thermal processing, vinegars were more effective at eluting antioxidants and isoflavones from seeds than other solutions such as acetic acid, citric acid and HCl solutions, distilled water, and phosphate buffer (pH 7.0).

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2001.09a
• /
• pp.34-58
• /
• 2001

Within the paper, an overview of organic farming in Europe countries is given and the Principle and skills of organic agriculture is shortly reported with special regard to Germany. The overview information on European organic farming is covered such as (1)development of organic farming, (2) organic farming organizations, (3)standards and certification, (4)implementation of EU council regulation, (5)state support, (6)implementation of Agenda 2000, (7)training and education, (8)advisory service and research situation. In the paper the principle and skills for organic farming which are practiced actually in the German organic farms is also reported. How to maintain and increase the fertility and microbiological activity of the soil by (1)cultivation of legumes, green manures or deep-rooting crops in multi-annual rotation system, (2)incorporation in the soil organic material, by-products from livestock farming is one of the major principle to organic crop production. Pest and diseases and weeds are controlled by any one, or a combination of the following measure; (1) choice of appropriate species and varieties, (2)appropriate rotation programs, (3)mechanical cultivation, (4)protection of natural enemies of pests through provision of favourable habitat and ecological buffer zone, (5)diversified ecosystems, (6)flame weeding, (7)natural enemies, (8)bio-dynamic preparations, (9)mulching and mowing, (10)grazing of animals, (11)mechanical controls, (12)steam sterilization.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.2
• /
• pp.139-147
• /
• 2016

Performances of urethane packing in the hydraulic breaker were analyzed using a finite element method. Because of high temperature and high pressure in the hydraulic breaker, it is better to use urethane rather than rubber as a packing material. We obtained the physical properties of urethane at elevated temperature by the tensile test. We analyzed buffer seal and U-packing maintaining the pressure and preventing oil leakage. Deformation, stress distribution, contact length, contact pressure of packing at each pressure step were obtained using finite element analysis. As the temperature increases, stress and contact force tend to decrease at low pressure. As the gap between piston and cylinder increases, contact length and contact forces decrease. Consequently, it is possible to design the packing section using these analyses, and construct a system to predict the possibility of oil leakage in the hydraulic breaker.