• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.41-48
• /
• 2010

A visualization study to evaluate bubble motion in a tab water filled cylindrical tank with a varying flow rate of compressed air is conducted. The flow rate of compressed air varies from 1 to 5 L/min. Time resolved images are acquired by a high speed camera in 10 bit gray level at 100 fps and the measurement volume is irradiated by a 230 W halogen lamp. It is observed that there are three different regions; the bubble formation region, the rising bubble region and the free surface region. During the rise of bubble, the shape is changed as if an elastic body. Based on the binarized bubble image, the mean diameters of rising bubbles are estimated at beneath of the free surface. As the gas flow rate increases, the mean diameter is increased and the rising velocity also increases with buoyancy force.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.454-459
• /
• 2003

The one of the most important subject to develop a LPDi engine is to suppress the generation of bubble inside LPG direct injector. For the purpose of this, in this study, the analogy visualization injector to visualize the generation and behavior of bubble, is manufactured and the bubbling phenomenon and behaviors are visualized and studied. The bubble inside the injector is generated at injection hole and after rising by buoyancy, it disappear around the top of a nozzle. The number of bubble generated is little changed regardless of the lapse of time but it is increased remarkably as the temperature around the injector is increased. With injection, the temperature around the injector at which the bubble is generated in_cylinder is much lower than that without injection because the transient pressure drop of fuel by injection.

• Journal of the Korean Society of Visualization
• /
• v.20 no.2
• /
• pp.55-62
• /
• 2022

We experimentally investigate a rising toroidal bubble impacting a free surface. The toroidal bubble is created by releasing pulsed air. By adjusting the volume and circulation of the toroidal bubble, the characteristics of interactions between the toroidal bubble and the free surface are identified. Because of the impact by the toroidal bubble, the free surface is convexly deformed upwards above the center point of the toroidal bubble, while the edge of the deformed free surface is pulled down. When the circulation of the bubble becomes stronger, the surface which was pulled down breaks eventually, and air above the free surface is entrained into water, forming an unstable toroidal bubble. The deformations at the center and edge of the free surface are in a linear relationship with the Froude number and the Weber number, respectively.

• Journal of the Korean Society of Visualization
• /
• v.15 no.2
• /
• pp.48-58
• /
• 2017

To analyze bubbles generated by an ABB (Air Bubble Barrier), we developed image processing procedure and statistical analysis method. Air was discharged from 5 mm nozzle as swarm form at the bottom of 1 m3 water tank. Flow rates of discharged air are ranged from 2 L/min to 20 L/min and these are corresponding to Reynolds number of 1766-17663. Rise velocity of bubble is extracted by using image process pretending intrusive method. Mean equivalent velocity was calculated using void fraction weighting factor. Bubble diameter is obtained and compared with correlations in the literature. Also, we present a correlation according to the result of this study. Mean velocity and mean diameter of bubbles increase with increasing gas Reynolds number. But these parameters show an asymptotic trend when they approach to high Reynolds number.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.279-283
• /
• 2009

Bubble jet loop heat pipe is what heat pipe operate in the horizontality. It is consist of one heating part creating bubble and one rounded U tube type radiator. This study shows whether the heat pipe operates well in the horizontality or not, and what optimized refrigerant charging rate is in the tube. But flow visualization of bubble jet heat pipe was not known. The purpose of this study is to visualize bubble jet loop heat pipe. The experiment was performed by changes of charging rate. Working fluid was R-141b. And heater of 220 V & 100 W was used. we take a photograph of flow visualization of bubble jet loop heat pipe in slow motion.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.67-73
• /
• 2022

Underwater environmental pollution caused by microplastic particles is considered to be one of the most serious problems in many oceans and countries nearby. Previous academic studies or field technologies tried to remove the micro-sized particles are often energy-consuming and costly, so it is hard to be employed for the actual uses. In this study, the mechanism of removal of micro-sized polyethylene spheres (size in order of 100㎛) using a rising bubble is experimentally investigated. It is found that the particles are either affected by bubble wake, thus translocated close to the water surface, or pushed far away by the surrounding fluid flow, depending on their initial position relative to the bubble. By scrutinizing the visualized behaviors of bubble-particle interaction, we draw the governing parameter, i.e., the polar angle between the particle and the bubble, to determine the effective capturing of the particles with a rising bubble.

• Journal of the Korean Society of Visualization
• /
• v.21 no.1
• /
• pp.47-56
• /
• 2023

Bubble condensation, which involves the interaction of bubbles within the subcooled liquid flow, plays an important role in the effective control of thermal devices. In this study, numerical simulations are performed using a VOF (Volume of Fluid) model to investigate the effect of tube diameter on bubble condensation. As the tube diameter decreases, condensation bubbles persist for a long time and disappear at a higher position. It is observed that for small tube diameters, the heat transfer coefficients of condensation bubbles, which is a quantitative parameter of condensation rate, are smaller than those for large tube diameters. When the tube diameter is small, the subcooled liquid around the condensing bubble is locally participated in the condensation of the bubble to fill the reduced volume of the bubble due to the generation of a backflow in the narrow space between the bubble and the wall, so that the heat transfer coefficient decreases.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.1-8
• /
• 2006

One of the most important subjects to develop a LPDi engine is to suppress the bubble generated inside the liquid LPG direct injector. For the purpose of this, the analogy visualization injector to visualize the generation and behaviors of bubble is manufactured, and the bubbling phenomenon and behaviors of bubble are visualized and investigated according to the change of the temperature around an injector wall, fuel pressure and a needle configuration. As results, it was found that the bubble inside the injector is generated around an injector hole and after rising by buoyancy it disappears around the top of a nozzle. The number of bubbles generated is little changed regardless of the lapse of time but it remarkably increases as the temperature around the injector increases. Also, it was known that as the sac volume in LPDi injector decreases the generation of bubble is more active and the rising velocity of bubble generated is increased.

• Journal of the Korean Society of Visualization
• /
• v.21 no.3
• /
• pp.75-84
• /
• 2023

In this study, we conducted analysis of bubble dynamics and flow of liquid phase change material(PCM) using shadowgraphy and particle image velocimetry(PIV). Characteristics of internal flow varied depending on locations of injection when solid PCM was liquefied from heated vertical wall. When bubbles rose immediately, they exhibited elliptical shape and zigzag trajectory. In contrast, when bubbles rose after merging at the bottom of solid PCM, with equivalent diameter for the inter-wall distance of 0.64 or greater, they showed a jellyfish shape and strong rocking behavior. It was observed by the PIV that the small ellipse bubbles made most strong flow inside the liquid PCM. Furthermore, the flow velocity was highest in the case of front injection, as the directions of temperature gradients and bubble-driven flow were aligned. The results underscore the significant influence of injection location on various characteristics, including bubble size, shape, rising path of bubbles, and internal flow.

• Journal of the Korean Society of Visualization
• /
• v.18 no.3
• /
• pp.52-60
• /
• 2020

When a bubble reaches a free surface, a bursting of the bubble produces a high speed jet. Despite its practical importance, significant effort has been devoted to investigate a bursting jet by a single bubble near a free surface. In the present study, we perform numerical simulations of bubbles in a tandem arrangement at Bo=0.05. The configuration of the tandem bubbles is systematically varied by changing a radius of a following bubble (RF) and the gap distance between two bubbles (L). Compared to a single bubble case, we show that the bursting bubble in the tandem arrangement accelerates, and the jet velocity increases. Moreover, we find that a critical gap distance at which the jet velocity unexpectedly changes exists in the tandem case.