• 한국세라믹학회지
• /
• 제23권5호
• /
• pp.75-80
• /
• 1986

The mechanical properties were measured for magnesium phosphate glasses containing small amounts of water. The decrease in hardness with increasing water content was resulted from a looser chain structure caused by water. The fracture of these glasses was changed from brittle fracture to plastic deformation as a results of the increased viscous flow with increasing water contents. The extent of any viscous flow or deformation initiating from the crack tips in these glasses could be considered as quite small.

• 한국군사과학기술학회지
• /
• 제5권2호
• /
• pp.207-216
• /
• 2002

In this paper, the study on the behavior of the deformation of brittle material, such as concrete, ceramic, was peformed by comparison of Lagrangian technique and Smoothed Particle Hydrodynamics using commercial nonlinear hydrodynamic numerical program, Autodyn_2D. The effect of SPH technique was proved by investigating the behavior of material deformation, velocity profile and pressure profile.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제16권2호
• /
• pp.104-109
• /
• 2016

Purpose: The purpose of this study is to analyze fracture behavior and failure mechanism of porous titanium for dental implant fabricated by space holder process. Method: Three porous titanium specimens with a specific volume fraction of open pore were test by 3 point bending and compression stress condition, respectively. Fracture appearance was observed by scanning electron microscope and discussed in relation with oxygen content. Results: For compression-tested specimens, two specimen showed brittle failure, while the other one showed normal failure after deformation. High oxygen content was detected in the brittle-fractured specimen. Several micro-cracks initiated at the struts propagated down to the bottom of the specimen resulting in normal failure. Conclusion: Oxygen contamination during the fabrication process can leads brittle premature failure, and hence quality problem of the porous titanium for dental implant.

• 한국공간구조학회논문집
• /
• 제7권6호
• /
• pp.61-68
• /
• 2007

대공간구조에서 접합부의 신뢰도는 매우 중요하다. 접합부에 사용되는 고력볼트의 나사부 유효단면적은 축부단면적보다 작고 볼트 축부에 락핀용 구멍이 있기 때문에 볼트 나사부 또는 락핀용 구멍에 응력집중 현상이 발생하여 취성 파단이 발생할 우려가 높다. 특히 접합부는 직렬형 구조로 이루어져 있다. 따라서 접합부에서의 극한상황시 파괴유형은 필히 취성파괴를 피해야 하며 연성파손으로 유도해야 한다. 따라서 본 연구에서는 볼 조인트 접합부의 소성변형능력을 향상시키고 현장에서 발생할 수 있는 시공오차의 흡수가 가능하도록, 볼트의 나사부나 핀부의 취성파단 없이 소성변형능력 향상을 목표로 하였다. 에너지흡수형 볼트를 사용함으로써 소성변형능력이 향상된 스페이스 프레임의 접합상세를 제안하였다.

• Earthquakes and Structures
• /
• 제16권5호
• /
• pp.575-588
• /
• 2019

Seismic design method based on bearing capacity has been widely adopted in building codes around the world, however, damage and collapse state of structure under strong earthquake can not be reflected accurately. This paper aims to present a deformation-based seismic design method based on the research of RC component deformation index limit, which combines with the feature of Chinese building codes. In the proposed method, building performance is divided into five levels and components are classified into three types according to their importance. Five specific design approaches, namely, "Elastic Design", "Unyielding Design", "Limit Design", "Minimum Section Design" and "Deformation Assessment", are defined and used in different scenarios to prove whether the seismic performance objectives are attained. For the components which exhibit ductile failure, deformation of components under strong earthquake are obtained quantitatively in order to identify the damage state of the components. For the components which present brittle shear failure, their performance is guaranteed by bearing capacity. As a case study, seismic design of an extremely irregular twin-tower high rise building was carried out according to the proposed method. The results evidenced that the damage and anti-collapse ability of structure were estimated and controlled by both deformation and bearing capacity.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.363-366
• /
• 2003

In nanomachining processes, chemical effects are more dominant factor compared with physical deformation. For example, during the nanoscratch on a silicon surface in the atmosphere, micro protuberances are formed due to the mechanochemical reaction between the diamond tip and the surface. On the contrary, in case of chemically stable materials, such as ceramics or glasse, the surface protuberance are not formed. The purpose of this study is to understand effects of the mechanochemical reaction between tip and surfaces on deformation behaviors of hard-brittle materials. Nanometerscale elasoplastic deformation behavior of single crystal silicon (100) was characterized with the surface protuberance phenomena, and compared with that of borosilicate (Pyrex glass 7740).

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.265-268
• /
• 2004

In this present study, mechanical properties of the Zr-Ti-Cu-Ni-Be bulk metallic glass are characterized by compression test over a wide range of temperatures and strain rates. Three different types of deformation behavior have been identified as a result, viz., Newtonian viscous flow, non-Newtonian flow and brittle fracture without plastic deformation. A transition state theory is applicable fur the flow stress - strain rate curve that contains the transition from Newtonian to non-Newtonian flow. Based on the relationship between viscosity and strain rate within undercooled liquid state, we can easily obtain the experimental deformation map and suggest the boundaries among different deformation behavior of this alloy.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.238-243
• /
• 2000

The effect of the temperature, the fatigue and the test speed on DEN(double edged notch) specimen which was made by the pp-rubber composites during fracture was stuied. DEN specimen was made on PP-rubber composites through the injection molding. With increasing temperature the fracture strength is linearly decrease and the fracture energy is first increase by $0^{\circ}C$ and after that decrease. In the same temperature the fracture strength during increasing the notch radius is hardly increase. The fracture behaviour at low and high test speed is different entirely. At high test speed plastic region is small and fracture behaviour was seen to brittle fracture tendency. The deformation mechanism of polypropylene-rubber composites during fracture was studied by SEM fractography. A strong plastic deformation of the matrix material ahead of the notch/crack occured. The deformation seem to be enhanced by a thermal blunting of the notch/crack.

• 한국해양공학회지
• /
• 제8권1호
• /
• pp.33-40
• /
• 1994

Welding of structure produces welding residual stresses which influence buckling strength, brittle fracture strength and cold crack on the weld parts. Therefore, it is very important to accurately analyze the residual stress before welding in order to guarantee the safety of weldment. If the weld length is long enough compared to the thickness and the breadth of plate, thermal and mechanical behaviors in the middle portion of the plate are assumed to be uniform along the thickness direction(z-axis). Thus, the following conditions(so-called plane deformation) can be assumed for the plate except near its end;1) distributions of stress and strain are independent on the z-axis;2) plane normal to z-axis before deformation remains plane during and after deformation. In this paper, plane-deformation thermal elasto-plastic problem is formulated by being based on the finite element method. Moreover special regards and paid to the fact that material properties in elastic and plastic region are temperature-dependence. And the method to solve the plane-deformation thermal elasto-plastic problem is shown by using the incremental technique. From the results of analysis, the characterisics of distribution of welding residual stress and plastic strain with the production mechanism are clarified.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.63-68
• /
• 2017

This study determines the selection of an appropriate jig material for the blade edge of the medical sapphire knife. The physical properties of the jig material affects the edge shape and chipping phenomenon in machining of the medical sapphire knife. If a grinding wheel is used, brittle workpieces such as sapphire are easily damaged by the propagation of cracks because the grinding force significantly increases. It is important to constantly maintain the grinding force in the grinding process of the brittle materials. The grinding force can be kept constantly by inducing the elastic deformation of the Jig material because the elastic deformation of brittle work-piece is negligibly low. The chipping phenomenon may be reduced by selecting the proper Jig material. Aluminum, copper, stainless steels and carbon steel were used as Jig materials. The experiment was conducted using a cast iron grinding wheel, which was installed on a conventional grinding machine with the ELID grinding system. The thickness and width of the chipping area were measured using an optical microscope and FE-SEM to analyze the shape of the blade edge. According to the experiment result, the chipping phenomenon decreased, and the sharp edge was formed when the jig materials with low elastic modulus were used.