• 대한치과보철학회지
• /
• 제36권1호
• /
• pp.104-119
• /
• 1998

The purpose of this study was pertinent design of the framework of the fixed bone anchored bridge using implants in the edentulous mandible through analysis of stress distribution by the three dimensional finite element analysis method. The results were as follows: 1. The L-shaped framework was favorable in restoring the edentulous mandible by implants and fixed bone anchored bridge. 2. The structure of the framework should be designed to endure the occlusal load because of stress concentration at the most distal abutment of the framework. 3. The stress at the distal implant where cantilever starts was twice as much as that of other portions. 4. Compressive stress was generated on the framework of the mesial side of the distal implant and extrusive force was induced to the mesially positioned implants. 5. The height of vertical plate was high as possible as can be to distribute stresses concentrating bucco-lingually and labio-lingually in the framework between abutments, 6. Reinforcement of the horizontal plate thickness was needed because stress was loaded more on the horizontal plate than on the vertical plate of the framework. 7. Lengthening of the vertical plate can compensate for any limitations in horizontal plate width.

• Wind and Structures
• /
• 제24권5호
• /
• pp.447-464
• /
• 2017

The flutter instability is one of the most important themes need to be carefully investigated in the design of long-span bridges. This study takes the central-slotted ideal thin flat plate as an object, and examines the characteristics of unsteady surface pressures of stationary and vibrating cross sections based on computational fluid dynamics (CFD) simulations. The flutter derivatives are extracted from the surface pressure distribution and the critical flutter wind speed of a long span suspension bridge is then calculated. The influences of angle of attack and the slot ratio on the flutter performance of central-slotted plate are investigated. The results show that the critical flutter wind speed reduces with increase in angle of attack. At lower angles of attack where the plate shows the characteristics of a streamlined cross-section, the existence of central slot can improve the critical flutter wind speed. On the other hand, at larger angles of attack, where the plate becomes a bluff body, the existence of central slot further reduces the flutter performance.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 가을 학술발표회 논문집
• /
• pp.333-339
• /
• 2003

Recently, the bridges become greater according to development of a construction technology. This phenomenon requires long span bridge, so that increases the dead weight. The orthotropic steel deck bridges have much advantages such as the light dead weight and the reduction of construction period. And almost whole process of carried out is manufactured at factory, so it can cause the increase of quality authoritativeness. But orthotropic steel deck bridge is consist of structure by welding, it can not avoid a lot of welding jobs, defects and transformation by welding are becoming problem accordingly. Specially, topical stress concentration phenomenon in cross connection area of longitudinal and transverse rib causes fatigue failure. The Bulkhead Plate for prevention of this stress concentration phenomenon was applied by changing the orthotropic steel deck of Williamsburg bridge in USA. But, it is principle that a Bulkhead Plate is not established in the domestic design standard. Therefore, it is estimated that the study for installation of Bulkhead Plate is needed. This treatise with considering these circumstances proves efficiency of Bulkhead Plate and will be presented optimal design details through finite element analysis according to change the geometrical of Bulkhead Plate and tile cross-connection area of longitudinal and transverse rib.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2003년도 봄 학술발표회 논문집
• /
• pp.185-192
• /
• 2003

This study presents the Optimum Evaluation of PS Concrete Deck and High Strength Two Plate Girder System. Recently, for the simplification of structure and the long length of bridge, a small number girder bridge which minimized a number of girder by two is much designed and constructed. For the structural analysis, a finite element formulation considering with even the matter of torsion in the three-dimensional problem is presented. And connectively, for the design of optimum section, an algorithm of optimum design is developed. The section of a small number girder bridge which constituted of two girders and PS Concrete Deck is optimized by using optimum program developed in this study. and two girders bridge refered in this study is proved a efficiency and a economy by being compared and checked to the general plate girder bridge with five girder and Reinforced Concrete Deck.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.1729-1734
• /
• 2008

This study developed a new separated shperical bridge bearing that can be used for replacement of existing bridge bearings without crushing bearing-concrete. The separated spherical bearing have the upper and lower sole plate connected by bolts to the upper plate under bridge-girders and the lower plate on bearing-concrete. The targets of the separated spherical bearing are the maximum 3 mm of up-lifting height during replacement and the maximum required time of 30 minutes. Four separated spherical bearings are manufactured and replaced the existing bearings of a railway bridge in service and the replacing tests was performed. The number of the tests is two and the target of maximum 3 mm and 30 minutes was satisfied.

• 한국구조물진단유지관리공학회 논문집
• /
• 제15권3호
• /
• pp.155-162
• /
• 2011

파형강판을 이용한 구조물은 기존의 철근콘크리트 구조물에 비하여 공기단축효과 및 경제성 등이 우수하고 유지관리비의 절감 측면에서 유리한 것으로 평가되고 있다. 최근 수로암거 및 생태 이동 통로등에 철근콘크리트 암거 대체 재료로 널리 활용되고 있으며 앞으로 적용실적이 더 증가할 것으로 예상된다. 파형강판을 사용한 구조물은 주로 아치형과 박스형의 두가지 형태이며, 아치형 구조물은 압축력에 의하여 설계하며 박스형 구조물은 플레이트 부재내의 모멘트에 의하여 설계한다. 따라서 본 연구에서는 기존의 대골형 파형강판보다 골의 피치와 깊이가 늘어난 성능 개선된 파형강판의 성능을 평가고하고 설계에 반영하기 위해 정적 압축 시험 및 휨시험을 수행하여 시험체 두께별 이음부의 극한강도 및 모멘트 강도를 검토 하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.389-396
• /
• 1998

One solution to prevent deterioration due to expansion joint and to extend lifetime of short span bridges, is jointless integral abutment bridge. To understand behavior of pile foundation of skewed plate girder bridge with integral abutment, finite element analysis was performed for the model of different skew angle from 90。 to 50。. Comparison of stresses at pile and abutment was made for each case. It is found that effect of temperature change is major factor to influence the behavior of skewed integral abutment bridge.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.524-529
• /
• 2003

This paper presents a experimental structural performance of steel-concrete hybrid bridge deck, which has studs to connect steel plate and concrete and T beam to improve structural performance, by steel plate shape, studs and load location. It proved that steel-concrete hybrid deck has a high structural performance and lightweight due to the efficient use of steel plate as a structural member, which has only used as formwork. In failure mode, few specimen failed at punching shear and many specimen at concrete crushing, therefore proved it has sufficient stability to punching shear which is the most frequent damage of bridge deck. Steel-concrete hybrid deck of plane steel plate has a high structural performance, and that of corrugated steel plate has a high reduction of weight.

• 한국전산구조공학회논문집
• /
• 제20권5호
• /
• pp.653-660
• /
• 2007

강바닥판 포장에 사용될 수 있는 특수아스팔트 중의 하나인 구스아스팔트는 $240^{\circ}C$에서 $260^{\circ}C$의 고온 상태에서 시공되기 때문에 강바닥판에 예상하지 못한 열응력 및 열변형을 발생시킬 수 있다. 따라서 구스아스팔트의 타설 중에 강바닥판에 미치는 열영향을 시공조건을 고려하여 사전에 평가하고 그 영향의 최소화를 위해서는 열전달 및 열응력 수치해석을 실시하여야 하지만 구조해석에서 주로 사용되는 평판/보요소의 특성상 3차원 구조해석 모델에서 구현하기가 매우 어렵다. 본 연구에서는 강바닥판 교량의 열영향해석을 위하여 일반적인 구조해석모델에 직접 적용할 수 있는 등가열원(EHS) 산정방법을 제안하였다. 강바닥판 교량의 구스아스팔트에 의한 열영향을 정확히 평가하기 위하여 (1) 기존의 실험결과를 이용하여 열전달해석에 필요한 물리량을 검증하고, (2) 정밀해석을 통해 3차원 교량모델에 적합한 등가열원을 산정하였으며, (3) 이를 해석모델에 적용하여 산정한 등가열원에 의한 수치해석방법의 타당성을 검증하였다. 본 연구에서 제안된 등가열원은 실제 강교량의 3차원 열전달 및 열응력 해석에 즉각 활용될 수 있으며, 등가열원산정기법은 용접잔류응력해석, 교량의 화재 해석 등 열영향을 받는 다른 공학적 해석에 응용될 수 있을 것으로 기대된다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제7권1호
• /
• pp.191-198
• /
• 2003

The pavement stiffness is scarcely used in structural analysis to design the superstructure of bridge. It is reasonable not to consider it in the case of asphalt concrete pavement over concrete deck because the pavement stiffness compared with the concrete deck plate can be ignored. However, sometimes, the pavement materials have a similar amount of elastic modulus to concrete and are applied to the orthotropic steel deck plate which has relatively less stiffness compared with the concrete deck plate. In this paper, the steel plate deck of a real bridge project was analyzed by considering the pavement stiffness by linear elastic FEM. It was assumed that a perfect bond between the steel plate deck and the pavement exited. The results indicated that the structural behavior of the orthotropic steel deck plate can be estimated enough to affect the evaluation result of structural capacity in some cases. Therefore, the investigations by experimental tests and more advanced numerical model are indispensible in figuring the design formula for considering the effects of pavement stiffness in the structural analysis of an orthotropic bridge.