• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.9
• /
• pp.101-109
• /
• 2001

The simulated die casting process in which the traditional plaster casting process is combined with rapid prototyping technology is being used to produce Al, Mg and Zn die casting prototypes. Because of lower mechanical properties induced by the large grain structure and incomplete filling, conventional plaster casting is not suitable for the simulated die casting process. A plaster casting process with pressurized vibration was developed for the simulated die casting process[5]. In this paper, numerical simulation for the filling stage of the process has been performed to show the effect of the pressurized vibration for complete filling. Treatment of boundary condition based on the finite element method has been proposed for imparted pressurized vibration in the plaster casting process.

• The Korean Journal of Ceramics
• /
• v.7 no.2
• /
• pp.70-73
• /
• 2001

Phase transformation of TiSi$_2$ confined in sub-micron area of which the size is around or smaller than the grain size of C49 TiSi$_2$ phase is studied. It has been known that the C49 to C54 phase change is massive transformation that occurs abruptly starting from C54 nuclei located at triple point grain boundaries of C49 phase. When the C49 phase is confined in sub-micron area, however, the massive phase transformation is observed to be hindered due to the lack of the triple point grain boundaries of C49 phase. Heat treatment at higher temperatures starts to decompose the C49 phase, and the resulting decomposed Ti atoms diffuse to, and react with, the underneath Si material to form C54 phase that exhibits spherical interface with silicon. The newly formed C54 grains can also trigger the massive phase transformation to convert the remaining undecomposed C49 grains to C54 grains by serving as nuclei like conventional C54 nuclei located at triple point grain boundaries.

• The Pure and Applied Mathematics
• /
• v.19 no.2
• /
• pp.147-169
• /
• 2012

We introduce a Heaviside-function formulation of the interaction between incompressible two-phase fluid and a non-deformable solid. Fluid and solid interact in two ways : fluid satises the Dirichlet boundary condition imposed by the velocity field of solid, and solid is accelerated by the surface traction exerted by fluid. The two-way couplings are formulated by the Heaviside function to the interface between solid and fluid. The cumbersome treatment of interface is taken care of by the Heaviside function, and the interaction is discretized in a simple manner. The discretization results in a stable and accurate projection method.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.154-160
• /
• 1998

This study describes a theoretical and experimental investigation of gas wave propagation in the pipe system. Most calculations of compressible flows in the pipe have been based on the method of characteristics. This technique has propensity to truncate waves and is difficult to apply to non-perfect gas. A method that describes the application of a two-step Lax-Wendroff acheme to solution of the unsteady one-dimentional flow in the pipe was developed. Theoretical calculations using both the method of characteristics and the two-step Lax-Wendroff method are presented including a realistic model for heat transfer and friction processes. In the present work, account is taken of the nonlinear behavior. For sections of parallel pipe, an one dimensional unsteady homentropic analysis is employed, and a numerical solution is obtained with the aid of a digital computer, using the method of characteristics and two-step Lax-Wendroff method. This analysis is then combined with boundary models, based on a quasi-steady flow approach, to give a complete treatment of the flow behavior in the pipe system.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.4
• /
• pp.355-361
• /
• 2012

This paper presents an experimental study on the detection and location of nonlinear scattering source due to the presence of fatigue crack in a laboratory specimen. The proposed technique is based on a combination of nonlinear elastic wave spectroscopy(NEWS) and time reversal(TR) focusing approach. In order to focus on the nonlinear scattering position due to the fatigue crack, we employed only one transmitting transducer and one receiving transducer, taking advantage of long duration of reception signal that includes multiple linear scattering such as mode conversion and boundary reflections. NEWS technique was then used as a pre-treatment of TR for spatial focusing of reemitted second harmonic signal. The robustness of this approach was demonstrated on a cracked specimen and the nonlinear TR focusing behavior is observed on the crack interface from which the second harmonic signal was originated.

• Journal of Korea Foundry Society
• /
• v.10 no.5
• /
• pp.399-407
• /
• 1990

The effect of thermal cycling and isothermal exposure on the high temperature microstructural stability of unidirectionally solidified $Al-CuAl_2$ eutectic composite has been studied. A coarsening procedures of lamellar eutectic structures were initiated at growth fault region because of diffusion through low angle boundary at this region. It was considered that thermally induced residual stresses produced by thermal cycling were high enough to increase the dislocation density in Al-rich matrix phase. However, it was also considered that dislocations generated by these high thermal stresses were annihilated at high temperature by stress relaxation. Consequently, the thermal cycling up to 1440 cycles between 20 and $520^{\circ}C$ did not affect the microstructural stability.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.663-668
• /
• 2001

Strength evaluation was carried out for the cylinder liner of a low-speed marine engine. Calculation of temperature distribution, nonlinear structural analysis, material test, and fatigue strength evaluation are briefly introduced in this paper. Strengths of five liner models are compared, and the effect of materials experiencing different heat treatment is evaluated. Structural analysis including boundary and material non-linearities was performed for axisymmetric liner models. High cycle (fatigue limit) and low cycle (fatigue life) fatigue analyses are carried out. As results, localized high stress was occurred next to the mount line. Maximum stresses are varied significantly with respect to different liner models and different materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.144-147
• /
• 2002

In this study, springback analysis of side rear member is carried out. Side rear member is one of the parts which shows severe springback problems. Forming, trimming, flanging and springback stages can be analyzed successively. From forming analysis, we identified the possible spots in which tearing may occur and can prevent failure. In springback analysis we used the boundary conditions same as applied to the blank on the checker so that the computational result can be compared with experimental one. Form .the comparison, springback analysis can yield relatively good results in a qualitative sense. However, in order to get good deformation result quantitatively, there still remains unsettled tasks in the forming analysis with very small die radius. It is found that we have to develop the element with better bending characteristics and precise contact treatment.

• Transactions of Materials Processing
• /
• v.4 no.3
• /
• pp.267-281
• /
• 1995

Preform design is one of the critical fields in metal forming. The finite element method(FEM) has been effective in designing preforms and process sequence, for which the backward tracing scheme of the rigid-plastic FEM has been explored. In this work a program using the backward tracing scheme by the rigid-plastic FEM is developed for three-dimensional plastic deformation, which is an extension of the scheme from two-dimensional cases. The calculation of friction between workpiece and die, and handling of boundary conditions during backward tracing require sophisticated treatment. The developed program is applied to upsetting of a rectangular block and to side pressing of a cylindrical workpiece. The results of the two applications show feasibility of the program on three-dimensional plastic deformation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.311-315
• /
• 2002

The coupled finite/boundary element method is used in numerical analysis for acoustic radiation from the vibration of rectangular composite plate which is simply supported. This analysis is validated using the Wallace equation for an isotropic plate. Active control of sound fields has been carried out using 3 pairs of piezoelectric sensor/actuator and a pair of viscoelastic material by passive constrained layer damping treatment. The results show that the optimal placement of piezoelectric sensor/actuator and VE patch is required to control the sound fields from a vibrating composite plate.