• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.4
• /
• pp.510-525
• /
• 2000

The effects of pretreatment of Co-Cr alloy, including two adhesive primers that contain either MDP or MAC-10, and silicoating on the bond The result sobtained as follows; o Strength of 4-META/MMA-TBB resin were investigated using FT-IR, SEM, and EDAX. o In the SEM observation of surface morphologies, the sandblasted specimen exibited a very rough surface, whereas the surfaces of the two groups primed with either MDP or MAC-10 were covered with a layer of primer, and the surface morphology of the silicoated specimen remained almost the same after sandblasting. o Before the thermocycling tests, the group treated with MDP demonstrated the highest mean tensile bond strength and the sandblasted group showed the lowest bond strength. o After 20,000 thermocyling, the mean tensile bond strength of the sandblasted group exhibited a 50% reduction in bond strength, while the others showed a $20\sim30%$ reduction. o Observation of the metal-resin interface revealed that in all groups the resin permeated the rough surface formed by sandblasting thereby producing a mechanical bond between the metal and the resin. It was also found that thermocycling resulted in a gap formation at the metal-resin interface of the specimens, and the sandblasted group exhibited a larger gap width than the other groups. o In fracture mode, all specimens indicated a cohesive fracture within the resin before thermocycling. However, thermocyling produced adhesive failure at the edge of the resin-metal interface in most specimens. The sandblasted group, which exhibited the lowest bond strength after thormocycling, also demonstrated the largest area of adhesive failure.

• Journal of the Korean Ceramic Society
• /
• v.46 no.5
• /
• pp.456-461
• /
• 2009

Chemical composition and status of chemical bonding of the YAG($Y_3Al_5O_{12}$) ceramics after the exposure to fluorine plasma have been investigated using X-ray photoelectron spectroscopy, with the analysis on its erosion behavior. On the surface, F showed the maximum content, decreasing with depth, meanwhile the cation composition remained almost constant, irrespective of the position. The peaks due to Y in the reaction layer consisted of two kinds, showing the Y-O and Y-F bonds. These surface modifications under fluorine plasma seem to promote the erosion of the YAG ceramics. Excess addition of $Al_2O_3$ or $Y_2O_3$ into stoichiometric YAG produced 2nd phases of $Al_2O_3$ and $YAlO_3$, respectively, resulting in the slight difference in the local erosion rates. But, the overall average erosion rate was not sensitive to such excess additions of $Al_2O_3$ or $Y_2O_3$.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.253-257
• /
• 2017

Graphene is a monolayer carbon material which consists of $sp^2$ bonding between carbon atoms. Its excellent intrinsic properties allow graphene to be used in various research fields. Many researchers believe that graphene is suitable for electronic device materials due to its high electrical conductivity and carrier mobility. Through chemical doping, n- or p-type graphene can be obtained, and consequently graphene-based devices which have more comparable structure to common semiconductor-based devices can be fabricated. In our research, we introduced the dielectrophoresis process to the chemical doping step in order to improve the effect of chemical doping of graphene selectively. Under 10 kHz and $5V_{pp}$ (peak-to-peak voltage), doping was conducted and the Au nanoparticles were effectively formed, as well as aligned along the edges of graphene. Effects of the selective chemical doping on graphene were investigated through Raman spectroscopy and the change of its electrical properties were explored. We proposed the method to enhance the doping effect in local region of a graphene layer.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.220-224
• /
• 2011

Die-upset magnets from a mechanically-milled Pr(Co,In)$_5$-type alloy are known to have a peculiar texture; the easy magnetization axis (c-axis) is perpendicular to the pressing direction. This peculiar texture is thought to be linked closely to the anisotropic mechanical properties of Pr(Co,In)$_5$-type hexagonal compounds. The hardness of the Pr(Co,In)$_5$-type crystal was measured using selectively grown grains in an annealed $Pr_{17}Co_{82}In_1$ alloy button, and the crystallographic orientation was determined by observing the magnetic domain image. The hardness (549 VHN) on the plane with a 'cogwheel'-type domain image was significantly higher than that (510 VHN) on the plane with a 'cigar'-type domain image, indicating that the inter-layer bonding force between the (000l) basal planes is stronger than that between the (hki0) planes. This suggests that the most probable slip plane is the (hki0) plane parallel to the c-axis. During die-upsetting of the Pr(Co,In)$_5$-type alloys the deformation proceeds by (hki0) plane slip, and the c-axis rotates to ultimately become oriented perpendicular to the pressing direction. It is proposed that the peculiar texture in the die-upset Pr(Co,In)$_5$-type magnets is probably developed by slip deformation of the (hki0) plane of the Pr(Co,In)$_5$-type grains.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.25 no.1
• /
• pp.76-92
• /
• 1998

The purpose of this study was to evaluate the possible efficacy of Nd-YAG laser as a dentin conditioner by observing the laser irradiation dentin surface under scanning electron micrograph and measuring shear bond strength of restored light-cured glass ionomer mold. Fifty intact premolars were prepared for shear bond strength tests. The teeth were randomly divided into five groups as follows; Group I. no treatment Group II. 10% poly acrylic acid, 20 sec Group III. laser treatment 2 w, 20 Hz, 2 sec Group IV. laser treatment 2 w, 20 Hz, 5 sec Group V. laser treatment 2 w, 20 Hz, 10 sec Samples of each group were restored with light-cured glass ionomer cement after dentin conditioning and then measuring the shear bond strength of each specimen were measured using universal testing machine. Additional ten premolars were prepared for SEM analysis The result from the this study can be summarized as follows. 1. Shear bond strength of polyacrylic acid-treated group (II) was significantly higher than other groups (p<0.05). 2. No statistically significant difference could be found between three laser-treated groups (III, IV, V) in shear bond strength(p>0.05) 3. According to the result of observation under SEM, Polyacrylic acid was shown to have removed the smear layer effectively and opened the dentinal tubules, whereas the laser has produced the irregular surface mainly composed of melted and fused structure. The microcracks found in laser-treated groups increased in number with irradiation time and formed the regular mesh-type in 10 sec-irradiation group. 4. The ultrastructural change of dentin surface created by laser irradiation was found to the improper for bonding of the glass ionomer restorative materials. And the lower shear bond strength of laser irradiated group might have been due to the failure to form the suit able dentin surface for the glass ionomer to penetrated into and form the proper micromechanical retention.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.60-65
• /
• 2014

Fe-based amorphous coatings were fabricated on a soda-lime glass substrate by the vacuum kinetic spray method. The effect of the gas flow rate, which determines particle velocity, on the deposition behavior of the particle and microstructure of the resultant films was investigated. The as-fabricated microstructure of the film was studied by field emission scanning electron microscopy (FE-SEM) and high resolution transmission electron microscopy (HR-TEM). Although the activation energy for transformation from the amorphous phase to crystalline phase was lowered by severe plastic deformation and particle fracturing under a high strain rate, the crystalline phases could not be found in the coating layer. Incompletely fractured and small fragments 100~300 nm in size, which are smaller than initial feedstock material, were found on the coating surface and inside of the coating. Also, some pores and voids occurred between particle-particle interfaces. In the case of brittle Fe-based amorphous alloy, particles fail in fragmentation fracture mode through initiation and propagation of the numerous small cracks rather than shear fracture mode under compressive stress. It could be deduced that amorphous alloy underwent particle fracturing in a vacuum kinetic spray process. Also, it is considered that surface energy caused by the formation of new surfaces and friction energy contributed to the bonding of fragments.

• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.1
• /
• pp.41-46
• /
• 2010

The interfacial adhesion strengths between screen-printed Ag film and epoxy resin-coated polyimide were evaluated by $180^{\circ}$ peel test method. Measured peel strength value was initially around $164.0{\pm}24.4J/m^2$, while the heat treatment during 24h at $120^{\circ}C$ increase peel strength up to $220.8{\pm}19.2J/m^2$. $85^{\circ}C/85%$ RH temperature/humidity treatment decrease peel strength to $84.1{\pm}50.8J/m^2$, which seems to be attributed to hydrolysis bonding reaction mechanism between metal and adhesive epoxy resin coating layer.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.449-454
• /
• 2002

A rectangular straight microchannel, integrated with the resistance temperature detectors(RTDs) for temperature sensing and a micro-heater for generating the Temperature gradient along the channel, was fabricated. Its dimension is 57${\mu}{\textrm}{m}$(H)$\times$200${\mu}{\textrm}{m}$(W)$\times$48,050${\mu}{\textrm}{m}$(L), and RTDs were placed at the inner-channel wall. Si wafer was used as a substrate. For the fabrication of RTDs, 5300$\AA$ thick Pt/Ti layer was sputtered on a Pyrex glass wafer. Finally, the glass wafer was bonded with Si wafer by anodic bonding, so that the RTDs are located inside the microchannel. Temperature coefficient of resistance(TCR) values of the fabricated Pt-RTDs were 2800~2950ppm$^{\circ}C$ and the variation of TCR value In the range of O~10$0^{\circ}C$ was less than 0.3％. Therefore, it was proved that the fabricated Pt-RTDs without annealing were excellent as temperature sensors. The temperature distribution in the microchannel was investigated as a function of mass flow rate and heating power. The temperature increase rate diminished with decreasing the applied power and increasing the mass flow rate. It was confirmed from the comparison with the simulation results that the temperature measured inside the microchannel is more accurate than measuring the temperature measured at the outer wall. The proposed temperature sensing method and microchannel are expected to be useful in microfluidics researches.

• Journal of Sensor Science and Technology
• /
• v.2 no.1
• /
• pp.19-27
• /
• 1993

Capacitive pressure sensor for low pressure measurements has been fabricated by using $n^{+}$ epitaxial layer electrochemical etching stop and glass-to-silicon electrostatic bonding technique. The sensor had hybrid configuration of a sensor chip, which consists of sensor capacitor and reference capacitor, and two output signal detection IC chips. A fabricated sensor, with a $1.0{\times}1.0 mm^{2}$ square size and a $10{\mu}m$ thick flat diaphragm, showed a 7.1 pF zero pressure capacitance, and 5.2 % F.S, sensitivity in 10 KPa pressure range. By using a capacitance to voltage converter, the thermal zero shift of 0.051 %F.S./$^{\circ}C$ and the thermal sensitivity shift of 0.12 %F.S./$^{\circ}C$ for temperature range of $5{\sim}45^{\circ}C$ were obtained.

• Polymer(Korea)
• /
• v.28 no.4
• /
• pp.305-313
• /
• 2004

A vacuum pressure-difference technique for making a nano-precision replica is investigated for various applications. Master patterns for replication were fabricated using a nano-replication printing (nRP) process. In the nRP process, any picture and pattern can be replicated from a bitmap figure file in the range of several micrometers with resolution of 200nm. A liquid-state monomer is solidified by two-photon absorption (TPA) induced by a femto-second laser according to a voxel matrix scanning. After polymerization, the remaining monomers were removed simply by using ethanol droplets. And then, a gold metal layer of about 30nm thickness was deposited on the fabricated master patterns prior to polydimethylsiloxane molding for preventing bonding between the master and the polydimethylsiloxane mold. A few gold particles attached on the polydimethylsiloxane stamp during detaching process were removed by a gold selecting etchant. After fabricating the polydimethylsiloxane mold, a nano-precision polydimethylsiloxane replica was reproduced. More precise replica was produced by the vacuum pressure-difference technique that is proposed in this paper. Through this study, direct patterning on a glass plate, replicating a polydimethylsiloxane mold, and reproducing polydimethylsiloxane replica are demonstrated with a vacuum pressure-difference technique for various micro/nano-applications.