• Restorative Dentistry and Endodontics
• /
• 제15권1호
• /
• pp.107-119
• /
• 1990

The purpose of this study was to evaluate the marginal adaptability of the amalgam restorations in applying the cavity varnish (Copalite$^{(R)}$) and dentin bonding agent (Scotchbond 2$^{(R)}$) under the scanning electron microscope. For this study, eighteen sound extracted human molars were selected. Class I cavities in 12 teeth and class V cavities in 6 teeth were prepared using an air turbine with No. 701 tungsten carbide bur and finished using a low speed handpiece with No. 557 fissure bur. The prepared specimens were then divided into three groups including 4 class I cavities and 2 class V cavities in each group and restored as follows ; Group I. All the prepared cavities were restored with amalgam only (Control). Group II. Two layers of Copalite$^{(R)}$ cavity varnish were applied to the cavities with a gentle stream of air after each application and cavities were restored with amalgam. Group III. The enamel cavity margins were etched with 37% phosphoric acid gel for 60 sec., rinsed for 30 sec. and dried. One layer of visible lightcured Scotchbond Dental Adhesive$^{(R)}$ was applied and immediately cured for 20 seconds with visible light-cure unit and cavities were restored with amalgam. All the specimens were cut at the neck of the teeth and the occlusal halves of specimens were sectioned buccolingually in the longitudinal axis centering the amalgam restorations, using the disk. The cut specimens were ground with sandpapers (400, 600, 800, 1000 grit), and cleaned for 5 minutes in the ultrasonic cleaner (Brason Co. U.S.A.). In the cut surfaces, the amalgam - tooth interfaces were examined under the scanning electron microscope (JSM, 35C type, JEOL). The obtained results were as follows ; 1. The amalgam-tooth interfaces were reduced more significantly in the Copalite$^{(R)}$ and Scotchbond 2$^{(R)}$ application group than in the control group. 2. In the class I cavities, the Scotchbond 2$^{(R)}$ application group showed the findings similar to the Copalite$^{(R)}$ application group in the cavity floor, and the marginal adaptability was better in the side wall than in the cavity floor. 3. In the class I cavities, the Scotchbond 2$^{(R)}$ application group showed better marginal adaptability in the occlusal margin than in the gingival margin. 4. The marginal adaptability was in the order of the Scothbond 2$^{(R)}$ application group, the Copalite$^{(R)}$ application group and the control group.

• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.929-933
• /
• 2010

3 차원 패키징을 위해 열가압 공정으로 제조된 Cu-Cu 접합 계면의 접합 특성을 평가하기 위해 4 점 굽힘 실험을 수행하였다. Cu가 코팅된 Si 웨이퍼 2 장을 $350^{\circ}C$에서 1 시간 동안 15kN 의 하중으로 접합시킨 후, 동일한 온도에서 1 시간동안 어닐닝을 수행하였다. 접합된 웨이퍼를 $30\;mm\;{\times}\;3\;mm$ 크기로 잘라 시험편을 준비하였다. 시험편의 중심에 깊이 $400\;{\mu}m$의 노치를 가공하였다. 시험기에 광학계를 부착하여 노치에서의 크랙 발생과 계면에서의 크랙 진전을 관찰하였다. 일정한 테스트 속도로 실험을 수행하여, 이에 상응하는 하중을 측정하였다. Cu-Cu 접합 계면 에너지는 $10.36\;J/m^2$ 으로 측정되었으며, 파괴된 계면을 분석하였다. 표면 분석 결과, $SiO_2$와 Ti의 계면에서 파괴가 일어났음을 확인하였다.

• Corrosion Science and Technology
• /
• 제7권1호
• /
• pp.50-60
• /
• 2008

The majority of the described experimental results deal with relatively pure aluminium. Variations were made in the pretreatment of the aluminum substrates and an investigation was performed on the resulting changes in oxide layer composition and chemistry. Subsequently, the bonding behavior of the surfaces was investigated by using model adhesion molecules. These molecules were chosen to represent the bonding functionality of an organic polymer. They were applied onto the pretreated surfaces as a monolayer and the bonding behavior was studied using infrared reflection absorption spectroscopy. A direct and clear relation was found between the hydroxyl fraction on the oxide surfaces and the amount of molecules that subsequently bonded to the surface. Moreover, it was found that most bonds between the oxide surface and organic functional groups are not stable in the presence of water. The best performance was obtained using molecules, which are capable of chemisorption with the oxide surface. Finally, it was found that freshly prepared relatively pure aluminum substrates, which are left in air, rapidly lose their bonding capacity towards organic functional groups. This can be attributed to the adsorption of contamination and water to the oxide surface. In addition the adhesion of a typical epoxy-coated aluminum system was investigated during exposure to water at different temperatures. The coating was found to quite rapidly lose its adhesion upon exposure to water. This rapid loss of adhesion corresponds well with the data where it was demonstrated that the studied epoxy coating only bonds through physisorptive hydrogen bonding, these bonds not being stable in the presence of water. After the initial loss the adhesion of the coating was however found to recover again and even exceeded the adhesion prior to exposure. The improvement could be ascribed to the growth of a thin oxyhydroxide layer on the aluminum substrate, which forms a new, water-stable and stronger bond with the epoxy coating. Two routes for improvement of adhesion are finally decribed including an interphasial polymeric thin layer and a treatment in boiling water of the substrate before coating takes place. The adhesion properties were finely also studied as a function of the Mg content of the alloys. It was shown that an enrichment of Mg in the oxide could take place when Mg containing alloys are heat-treated. It is expected that for these alloys the (hydr)oxide fraction also depends on the pre-treatment and on the distribution of magnesium as compared to the aluminium hydroxides, with a direct impact on adhesive properties.

• 마이크로전자및패키징학회지
• /
• 제16권3호
• /
• pp.31-37
• /
• 2009

3차원 소자 집적을 위한 저온접합 공정 개발을 위해 Cu-Cu 열 압착 접합을 $300^{\circ}C$에서 30분간 실시하고 $N_2+H_2$, $N_2$분위기에서 전 후속 열처리 효과에 따른 정량적인 계면접착에너지를 4점굽힘시험법을 통해 평가하였다. 전 열처리는 100, $200^{\circ}C$의 $N_2+H_2$ 가스 분위기에서 각각 15분간 처리하였고, 계면접착에너지는 2.58, 2.41, 2.79 $J/m^2$로 전 열처리 전 후에 따른 변화가 없었다. 하지만 250, $300^{\circ}C$의 $N_2$ 분위기에서 1시간씩 후속 열처리 결과 2.79, 8.87, 12.17 $J/m^2$으로 Cu 접합부의 계면접착에너지가 3배 이상 향상된 결과를 얻을 수 있었다.

• 대한금속재료학회지
• /
• 제48권12호
• /
• pp.1116-1122
• /
• 2010

Metal interconnections of multilayer Al/Ni and TiW/seed-Ni/Ni were formed on glass, and the adhesion strength and nanoindentation response of the composite layers were evaluated. The Al/Ni multilayer was formed by an anodic bonding of glass to Al and subsequent electroless plating of Ni, while the TiW/Ni multilayer was fabricated by sputter deposition of TiW and seed-Ni onto glass and electroless plating of Ni. Because of the diffusion of aluminum into glass during the anodic bonding, anodically bonded glass/Al joint exhibited greater interfacial strength than the sputtered glass/TiW one. The Al/Ni on glass also showed excellent resistance against delamination by bending deformation compared to the TiW/seed-Ni/Ni on glass. From the nanoindentation experiment of each metal layer on glass, it was found that the aluminum layer had extremely low hardness and elastic modulus similar to the glass substrate and played a beneficial role in the delamination resistance by lessening stress intensification at the joint. The indentation data of the multilayers also supported superior joint reliability of the Al/Ni to glass compared to that of the TiW/seed-Ni/Ni to glass.

• Restorative Dentistry and Endodontics
• /
• 제36권5호
• /
• pp.409-418
• /
• 2011

연구목적: 이 연구는 상아질 표면에 Er:YAG 레이저를 조사하지 않는 군, 레이저를 조사한 군, 레이저를 조사한 후 부가적인 산처리를 한 군으로 분류하여 2단계 단일병 전부식 접착시스템과 자가부식 프라이머 접착시스템을 이용하여 복합레진을 접착하였을 때 이러한 표면처리가 복합레진의 미세전단 결합강도와 결합계면에 미치는 영향을 비교하기 위하여 시행하였다. 연구 재료 및 방법: 32개의 발거된 대구치의 교합면측 상아질을 이용하였고, 상아질의 표면처리는 1군과 4군에서 각각 인산과 자가부식 프라이머로 하였으며, 2군과 5군은 Er:YAG 레이저로 에칭처리하였고, 3군과 6군은 레이저로 에칭한 후 다시 각각 인산과 자가부식 프라이머로 하였다. 1군, 2군, 3군은 Single Bond 2와 Z 250 (3M ESPE)을 이용하였고, 4군, 5군, 6군은 Clearfil SE Bond와 Clearfil AP-Z (Kuraray)을 이용하여 상아질 면에 Tygon tube를 접착하였다. 각 군의 미세전단 결합강도를 측정한 후 통계 처리하였고, 또한 6개의 시편에서 복합레진과 상아질 계면을 주사전자현미경하에서 관찰하였다. 결과: Single Bond 2를 사용한 군에서 2군의 결합강도는 1군과 3군보다 통계학적으로 낮게 나타났으며, Clearfil SE Bond를 사용한 군에서 4군, 5군, 6군의 결합강도는 각각 통계학적으로 유의한 차이를 나타내었다(p < 0.05). 2군과 5군은 아주 짧고 가는 레진테그가 관찰되었고, 3군과 6군은 길고 가는 레진테그와 레진테그의 측지가 관찰되었다. 결론: 레이저로 에칭 처리한 상아질에 대한 부가적인 산 처리나 자가부식 프라이머의 처리는 상아질의 접착력을 향상시켰다.

• 대한치과기공학회지
• /
• 제33권4호
• /
• pp.349-357
• /
• 2011

Purpose: In this study, for the reasons of observing the changes when using bonding agent with Ni-Cr alloy and Co-Cr alloy and using VM13 and Vintage MP ceramic which have the disparity in coefficient of thermal expansion, it is carried out to evaluate the characteristics of the bonding agent through the analysis of the interface between metal and ceramic and the analysis of bond strength by variable. Methods: The surface treatment was performed on the two kinds of alloy(Ni-Cr alloy and Co-Cr alloy) specimens, which were sandblasted and were treated with bonder application. The metal-ceramic interfaces were analyzed with EPMA in order to ionic diffusion, and the shear test was performed. Results: As a result of observation of metal-ceramic interfacial properties, it was observed that Cr atoms were spread from the alloy body to the ceramic floor in the specimen of Group B. It was also seen that Cr, W atoms were spread from the alloy body to the ceramic floor in the specimen of Group S. In consequence of observing Shear bond strength, it was calculated that the specimen of BSV was 27.75(${\pm}11.21$)MPa, BSM was 27.02(${\pm}5.23$)MPa, BCV was 30.20(${\pm}5.99$)MPa, BCM was 27.94(${\pm}10.76$)MPa, SSV was 20.83(${\pm}2.58$)MPa, SSM was 23.98(${\pm}3.94$)MPa, SCV was 32.32(${\pm}4.68$)MPa, and SCM was 34.54(${\pm}10.63$)MPa. Conclusion: In the metal-ceramic interface of Bellabond plus sample group, diffusion of Cr atoms was incurred and diffusion of C Cr atoms and W atoms in the sample group of $Starloy{(R)}\;C$ was observed. Using bonding agent showed the higher bond strength than using the sand blasting treatment. In the Bellabond plus alloys, the specimen group with the use of binding materials showed higher shear bond strength, but didn't show statistically significant differences (p>0.05). In the $Starloy{(R)}\;C$ alloys, the specimen group with the use of binding materials showed higher shear bond strength and statistically significant differences(p<0.05). In terms of VM13 ceramic, it was in the Bellabond plus alloys that the high shear bond strength was showed, but there's no statistically significant differences(p>0.05). In terms of Vintage MP ceramic, it was in the $Starloy{(R)}\;C$ alloys that the high shear bond strength was showed and statistically significant differences(p<0.05). Metal-ceramic to fracture of the shear strength measurements and an analysis of all aspects of military usage fracture of the composite, respectively.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.59-60
• /
• 2002

In this digest, we briefly review our current molecular dynamics (MD) simulations that utilize both the reactive empirical bond order potential (REBO) and the adaptive intermolecular REBO (AIREBO) potential energy functions. The AIREBO potential includes intermolecular interactions, so that self·assembled monolayers, and liquids, can be modeled. We have examined the mechanical and tribological properties of model self assembled monolayers and amorphous carbon films. Self-assembled monolayers are modeled by covalently bonding hydrocarbon chains to diamond substrates. Because the REBO potentials can model chemical reactions, specific compression and sliding induced chemical reactions were identified.

• 한국정밀공학회지
• /
• 제10권3호
• /
• pp.152-160
• /
• 1993

This paper presents experimental study of the static and dynamic fracture toughness behavior of a A1-6061 aluminum alloy reinforced alumina( .delta. -A1$_{2}$0$_{3}$) whiskers with 5%, 10%, 15% volume fraction. The static fracture tests using three-point bending specimen were performed by UTM25T. And drop weight impact tester performing dynamic fracture tests was used to measure dynamic locads applied to a fatigue-precracked specimes. The oneset of crack initiation was detected uwing a strain gage bonded near a crack tip. The value of static fracture toughness $K_{IC}$ and dynamic fracture toughness $K_{ID}$ were decided on the basis of linear elastic fracture mechanics. The effects of fiber volume fraction and loading on fracture toughness were investigated. The distribution of whiskers, bonding state and fracture interfaces involved in void, fiber pull-out state were investigated by optical microscopy(OM) and scanning electron microscopy(SEM)

• 대한전자공학회논문지
• /
• 제25권1호
• /
• pp.27-32
• /
• 1988

Electron Spectroscopy for Chemical Analysis(ESCA) allowes the determination of the elemental composition and the bonding state of the surface atomes in the interface between two materials. In the binding energies of ESCA spectrum, there are zero error, voltage scaling error and random error. Accurate analysis of the intensity energy response functions and accurate calibration of the energy scale are essential to use X-ray photoelectron spectron meter. At the results of the calibration of the ESCA spectra in the copper and cordierite (Mg2Al4Si5kO18) interfaces, the errors relative to the copper are -3.03 eV for the zero error -z,-197 ppm for the voltage scaling error -V and 6.9 meV for the random error -R. The method of the calibration is able to apply for the binding energy calibration of the another ESCA spectra.