• 대한치과교정학회지
• /
• 제40권2호
• /
• pp.87-94
• /
• 2010

전단결합강도를 강화하기 위해 레이저를 이용한 부식과 산을 이용한 부식의 비교 연구가 많이 진행되어왔다. 본 연구에서는 Er,Cr:YSGG laser와 전통적인 산부식법을 혼합한 방법의 전단결합강도의 변화에 대한 평가를 하고자 한다. 교정적인 목적으로 발치된 64개의 건전한 소구치를 이용하여 16개씩 4개의 군으로 나누었다. 첫 번째 군은 37% 인산을 15초 적용시키는 전통적인 부식 방법을 택하였고, 두 번째 군은 물방울레이저로 1.5 W로 10초간 부식시킨 후 전통적인 산부식 방법을 시행하였다. 세 번째 군은 두 번째 군과 같지만 산부식을 먼저 시행한 후 물방울레이저로 부식시켰다. 네 번째 군은 물방울레이저를 이용하여 1.5 W로 15초간 부식시켰다. 이후 전단결합강도의 측정 및 치아 표면의 특징 관찰, 그리고 접착제잔류지수를 평가하였다. 두 번째, 세 번째 군은 첫 번째, 네 번째 군에 대하여 전단결합강도가 높게 측정되었다. 하지만 두 가지 기법의 복합사용 순서를 달리한 두 번째, 세 번째 군 사이에는 통계적으로 유의한 차이가 나지 않았다. 기존 산부식을 이용한 브라켓 접착법보다 산부식과 Er,Cr:YSGG laser를 복합적으로 사용 시, 향상된 전단결합강도를 얻을 수 있다.

• 방사선산업학회지
• /
• 제6권1호
• /
• pp.31-40
• /
• 2012

There are two methods to fabricate the readout electronic to a large-area CMOS image sensor (LACIS). One is to design and manufacture the sensor part and signal processing electronics in a single chip and the other is to integrate both parts with bump bonding or wire bonding after manufacturing both parts separately. The latter method has an advantage of the high yield because the optimized and specialized fabrication process can be chosen in designing and manufacturing each part. In this paper, LACIS chip, that is optimized design for the latter method of fabrication, is presented. The LACIS chip consists of a 3-TR pixel photodiode array, row driver (or called as a gate driver) circuit, and bonding pads to the external readout ICs. Among 4 types of the photodiode structure available in a standard CMOS process, $N_{photo}/P_{epi}$ type photodiode showed the highest quantum efficiency in the simulation study, though it requires one additional mask to control the doping concentration of $N_{photo}$ layer. The optimized channel widths and lengths of 3 pixel transistors are also determined by simulation. The select transistor is not significantly affected by channel length and width. But source follower transistor is strongly influenced by length and width. In row driver, to reduce signal time delay by high capacitance at output node, three stage inverter drivers are used. And channel width of the inverter driver increases gradually in each step. The sensor has very long metal wire that is about 170 mm. The repeater consisted of inverters is applied proper amount of pixel rows. It can help to reduce the long metal-line delay.

• Restorative Dentistry and Endodontics
• /
• 제35권2호
• /
• pp.69-79
• /
• 2010

본 연구는 여러 레진 시멘트의 film thickness에 따른 상아질과 간접 레진 수복물 간의 미세인장 결합 강도를 측정하고, 각 레진 시멘트의 중합 수축 및 굴곡 강도, 탄성 계수를 비교 분석하며, 접착 계면 및 파단면의 주사전자 현미경 관찰을 통하여 레진 시멘트의 film thickness가 레진 간접 수복물의 접착 효율에 미치는 영향을 평가하고자 시행하였다. 복합 레진형 레진 시멘트인 Variolink II와 Duo-Link, 접착형 레진 시멘트인 Panavia F와 Rely X Unicem의 4가지 레진 시멘트를 사용하였고, 각각의 시멘트를 film thickness에 따라 < $50\;{\mu}m$ (control)의 대조군과 $50\;{\mu}m$ (T50), $100\;{\mu}m$ (T100), $150\;{\mu}m$ (T150)의 실험군으로 나누어 총 16개의 군으로 분류하였다. 데이터는 ANOVA와 Duncan's multiple comparison test (p < 0.05)를 이용하여 통계 분석하였으며 다음과 같은 결론을 얻었다; 1. Variolink Ⅱ는 모든 film thickness에서 접착형 레진 시멘트보다 높은 결합 강도를 나타냈지만(p < 0.05), Duo-Link는 대조군을 제외하고는 통계학적 유의차가 없었다(p > 0.05). 2. Film thickness가 증가할수록 복합 레진형 레진 시멘트의 결합 강도는 유의성 있게 감소(p < 0.05)하는 경향을 보인 반면, 접착형 레진 시멘트는 통계학적 유의차가 없었다(p > 0.05). 3. Panavia F는 통계학적으로 유의성 있게 낮은 중합 수축량을 나타냈다(p <0.05). 4. 굴곡 강도와 탄성 계수는 복합 레진형 레진 시멘트가 접착형 레진 시멘트보다 유의성 있게 높게 나타났다(p < 0.05). 5. FE-SEM 관찰 결과 결합 강도가 높은 복합 레진형 레진 시멘트는 균일한 접착층과 잘 발달된 resin tag 소견을 보였으나, 접착형 레진 시멘트는 불분명한 접착층과 resin tag 소견을 나타냈다. 파단면 관찰에서 복합 레진형 레진 시멘트는 혼합형 파괴 양상을 나타냈으나 접착형 레진 시멘트는 접착성 파괴 양상을 나타냈다.

• 한국태양에너지학회 논문집
• /
• 제39권4호
• /
• pp.1-9
• /
• 2019

Modules using 6 inch cells have problems with loss due to empty space between cells. To solve this problem made by shingled structure which can generate more power by utilizing empty space by increasing the voltage level than modules made in 6inch cell. Thus, in this paper, the c-Si cutting cells were produced using nanosecond green laser, and then the ECA was sprayed and cured to perform cutting cell bonding. Three types of ECA materials (B1, B2, B3) with Ag as the main component were used, and experimental conditions varied from 5 to 120 seconds of curing time, 130 to $210^{\circ}C$ of curing temperature, and 1 to 3 of curing numbers. As a results of experiments varying curing time, B1 showed efficiency 19.88% in condition of 60 seconds, B2 showed efficiency 20.15% in 90 seconds, and B3 showed efficiency 20.27% in 60 seconds. In addition, experiments with varying curing temperature, It was confirmed highest efficiency that 20.04% in condition of $170^{\circ}C$ with B1, 20.15% in condition of $150^{\circ}C$ with B2, 20.27% in condition of $150^{\circ}C$ with B3. These are because the Ag particles are densely formed on the surface to make the conduction path. After optimizing the conditions of temperature and curing time, the secondary-tertiary curing experiments were carried out. as the structural analysis, conditions of secondary-tertiary curing showed cracks that due to damp heat aging. As a result, it was found that the ECA B3 had the highest efficiency of 20.27% in condition of 60 seconds of curing time, $150^{\circ}C$ of curing temperature, and single number of curing, and that it was suitable for the manufacture of Solar cell of shingled structure rather than ECA B1 and B2 materials.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.168-172
• /
• 2014

Under concentrated illuminations, the solar cells show higher efficiencies mainly due to an increase of the open circuit voltage. In this study, InGaP/InGaAs/Ge triple-junction solar cells have been grown by a low pressure metalorganic chemical vapor deposition. Photovoltaic characteristics of the fabricated solar cells are investigated with a class A solar simulator under concentrated illuminations from 1 to 100 suns. Ideally, the open circuit voltage should increase with the current level when maintained at the same temperature. However, the fabricated solar cells show degraded open circuit voltages under high concentrations around 100 suns. This means that the heat sink design is not optimized to keep the cell temperature at $25^{\circ}C$. To demonstrate the thermal degradation, changes of the device performance are investigated with different bonding conditions and heat sink materials.

• 펄프종이기술
• /
• 제47권6호
• /
• pp.164-169
• /
• 2015

Nowadays blending ratio of OMG (old magazine) in recovered paper used for manufacturing newspaper have been increased. When large amount of OMG is consumed in newsprint mill, brightness can be improved by inorganic pigments of coating layer. On the other hand decrease in yield of deinking process will be encountered because the pigments can be removed as reject of froth flotation process. Therefore selection of the optimal deinking agent is an important. Non-ionic surfactant have been used widely in newsprint mill. Non-ionic surfactant has amphoteric characteristics. Hydrophilic group is ethylene and propylene oxide that can induce hydrogen bonding with water molecules. In this regard, cloud point is an important parameter in order to control efficiency of deinking process because hydration of the hydrophobic group can be varied according to temperature of a system. In this study, deinking properties of ONP at high blending ratio of OMG was analyzed according to cloud points of non-ionic surfactants. $L^*$, $a^*$, $b^*$, brightness and effective residual ink concentration did not affected by the change of cloud points. Especially, flotation reject decreased significantly according to increase in cloud point of the non-ionic surfactant. Consequently, when a nonionic surfactant having a cloud point higher than the temperature of the system is used, properties of the deinked pulp can be maintained and yield of deinking process can be improved.

• 청정기술
• /
• 제21권4호
• /
• pp.235-240
• /
• 2015

본 연구에서는 열변색 물성을 향상시키기 위한 방안의 하나로 0~0.5 at % 범위의 티타늄을 도핑한 이산화 바나듐(Ti-VO₂)을 제조하였다. Ti-VO₂ 입자들은 바나딜설페이트, 중탄산암모늄, 사염화 티타늄 등을 사용하여 바나듐 화합물 전구체를 제조한 후 열분해법을 이용하여 제조하였다. 제조된 시료들의 결정 구조, 형상, 화학적 구조 및 열변색 특성은 X-선 회절분석기, 전계방사 주사전자현미경, X-선 광전자 분광기, 시차주사열량분석기, 자외선-가시광선-근적외선 분광기 등을 이용하여 분석하였다. 제조된 Ti-VO₂ 입자들은 단사 결정계를 지니고 있고, 또한 티타늄이 이산화 바나듐 결정내에 잘 도핑되어 있음을 확인할 수 있었다. 티타늄 도핑량이 증가함에 따라 최종 Ti-VO₂ 입자들의 크기가 작아지고 상전이 온도가 낮아졌으며, 또한 NIR switching efficiency는 증가하였다.

• Bulletin of the Korean Chemical Society
• /
• 제31권10호
• /
• pp.2923-2928
• /
• 2010

This study examined the synthesis of the crystal structure of bis(2,2'-bipyridine)nitrato zinc (II) nitrate, $[Zn(bipy)_2(NO_3)]^+NO_3^-$ using a microwave treatment at 300 W and 60 Hz for the application to dye-sensitized solar cells. The simulated complex structure of the complex was optimized with the density functional theory calculations for the UV-vis spectrum of the ground state using Gaussian 03 at the B3LYP/LANL2DZ level. The structure of the acquired complex was expected a penta-coordination with four nitrogen atoms of bipyridine and the oxygen bond of the $NO_3^-$ ion. The reflectance UV-vis absorption spectra exhibited two absorptions (L-L transfers) that were assigned to the transfers from the ligand ($\sigma$, $\pi$) of $NO_3$ to the ligand ($\sigma^*$, $\pi^*$) of pyridine at around 200 - 350 nm, and from the non-bonding orbital (n) of O in $NO_3$ to the p-orbital of pyridine at around 450 - 550 nm, respectively. The photoelectric efficiency was approximately 0.397% in the dye-sensitized solar cells with the nanometer-sized $TiO_2$ at an open-circuit voltage (Voc) of 0.39 V, a short-circuit current density (Jsc) of $1.79\;mA/cm^2$, and an incident light intensity of $100\;mW/cm^2$.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.533-538
• /
• 2014

Today, silicon and epoxy resin are used as materials of conversion lenses for white LEDs on the basis of their good bonding and transparency in LED packages. But these materials give rise to long-term performance problems such as reaction with water, yellowing transition, and shrinkage by heat. These problems are major factors underlying performance deterioration of LEDs. In this study, in order to address these problems, we fabricated a conversion lenses using glass, which has good chemical durability and is stable to heat. The fabricated conversion lenses were applied to a remote phosphor type. In this experiment, the conversion lens for white LED was coated on a glass substrate by a screen printing method using paste. The thickness of the coated conversion lens was controlled during 2 or 3 iterations of coating. The conversion lens fabricated under high heat treatment temperature and with a thin coating showed higher luminance efficiency and CCT closer to white light than fabricated lenses under low heat treatment temperature or a thick coating. The conversion lens with $32{\mu}m$ coating thickness showed the best optical properties: the measured values of the CCT, CRI, and luminance efficiency were 4468 K, 68, and 142.22 lm/w in 20 wt% glass frit, 80 wt% phosphor with sintering at $800^{\circ}C$.

• 마이크로전자및패키징학회지
• /
• 제29권1호
• /
• pp.71-75
• /
• 2022

Graphene oxide를 ZnCl₂:NaCl 전해질과 함께 교반한 후 순환 전압전류법에 의해 전기화학적으로 제막하여 유기태양전지용 전자수송층 제막과정을 단순화하고 이를 갖는 유기태양전지를 제작하였다. 소자의 구조는 FTO/ZnO:graphene 전자수송층/P3HT:PCBM 광활성층/PEDOT:PSS 정공수송층/Ag이다. ETL의 형태 및 화학적 특성은 주사전자현미경(scanning electron microscopy, SEM), X선 광전자 분광법(X-ray photoelectron spectroscopy, XPS), 라만 분광법으로 확인하였다. XPS 측정결과 ZnO 금속산화물 및 탄소결합이 동시에 확인되었고, 라만 분광법에서 ZnO와 graphene 피크를 확인하였다. 제작한 태양전지의 전기적 특성을 솔라시뮬레이터로 측정하였고 0.05 V/s의 속도로 2회 제막한 ETL 소자에서 1.94%의 가장 높은 광전변환효율을 나타내었다.