• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5A
• /
• pp.743-750
• /
• 2000

In this paper, low-power block filtering architecture for digital If down sampler and up sampler is proposed. Software radio technology requires low power and cost effective digital If down and up sampler. Digital If down sampler and up sampler are accompanied with decimation filter and interpolation filter, respectively. In the proposed down sampler architecture, it is shown that the parallel and low-speed processing architecture can be produced by cancellation of inherent up sampler of block filter and down sampler. Proposed up sampler also utilizes cancellation of up sampler and inherent down sampler of block filtering structure. The proposed architecture is compared with the conventional polyphase architecture.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2014.06a
• /
• pp.77-78
• /
• 2014

A new MCMC method for optimization is presented in this paper, which is called the scanline block Gibbs sampler. Due to its slow convergence speed, traditional Markov chain Monte Carlo (MCMC) is not widely used. In contrast to the conventional MCMC method, it is more convenient to parallelize the scanline block Gibbs sampler. Since The main part of the scanline block Gibbs sampler is to calculate message between each edge, in order to accelerate the calculation of messages passing in scanline sampler, it is parallelized in GPU. It is proved that the implementation on GPU is faster than on CPU based on the experiments on the OpenGM2 benchmark.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.725-732
• /
• 2003

It was achieved that Rowecell test for this undisturbed sample was picked by Block sampler($\phi$:250mm, L:500mm) and hydraulic piston sampler($\phi$:76mm, L:850mm) in the marine clay of YONGYUDO and YEONGJONGDO in this research. Ratio of coefficient of consolidation was analyzed through comparison with C$\_$h/ by CPTu and C$\_$v/ and C$\_$h/ by existent consolidation test. According to analysis, coefficient of consolidation of block sample is fairly greater than coefficient of consolidation of piston sample. And the bigger diameter of undisturbed sample, sample disturbance could know decreasing. Coefficient of consolidation by Rowecell test measured more greatly than coefficient of consolidation by existent consolidation test. Rowecell test could know decreasing consolidation rate because of smear effect by Mandrel injection. Also, C$\_$h/ by CPTu shows deviation by each analysis method, selection of suitable analysis method judged by important leading in the coefficient of consolidation.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.25 no.4
• /
• pp.472-481
• /
• 2015

Objectives: Welding is a major task in shipbuilding yards that generates welding fumes. A significant amount of welding in shipbuilding yards is done on steel. Inevitably, manganese is present in the base metals being joined and the filler wire being used and, consequently, in the fumes to which workers are exposed. The objective of this work was to characterize manganese exposure associated with work area, total and particle size-selective mass concentration, and compare the mass concentrations obtained using a three-piece cassette sampler, size-selective impactor sampler and blood manganese concentrations. Materials: All samples were collected from the main work areas at one shipbuilding yard. We used a three piece cassette sampler and the eight stage cascade impactor sampler for the airborne manganese mass concentration of total and all size fractions, respectively. In addition, we used the results of health examination of workers sampled for airborne manganese. Results: The oder of high concentration of airborne manganese in shipbuilding processes was as follows; block assembly, block erection, outfitting installation, steel cutting, and outfitting preparation. The percentages of samples that exceeded the OES of the ministry of employment and labor by the cassette sampling method was 12.5%, however 59.1% of sampled workers by the impactor sampling method exceeded the TLV of the ACGIH. Conclusions: Even though the manganese concentrations in blood of workers exposed to higher airborne manganese concentration were higher than among those exposed to lower concentrations, there was no difference in blood manganese concentrations among work duration. The data analyzed here by characterizing size-selective mass concentrations indicates that the inhaled manganese of welders in shipbuilding yards could be mostly manganese-containing respirable particle sizes.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.639-646
• /
• 2000

It is important to estimate the mechanical properties of clay since it is directly related to the design and the construction of geotechnical structures. Site exploration, which is composed of boring, sampling, in-situ, or laboratory tests, is preformed to estimate the mechanical properties. However, mechanical properties of clay measured from laboratory test may be different from in-situ properties due to disturbances occurred during sampling, transportation, storage, and trimming. In this study, the degree of disturbance according to sampling method was estimated with the test results of CK/sub o/U triaxial compression test on Yangsan clay. The soil samples were obtained by three types of sampling method, j.e., 76mm-tube sampler, 76mm-piston sampler, and block sampler. In order to evaluate the quality of samples, volumetric strain, undrained shear strength, secant Young's modulus, and pore pressure coefficient at peak measured from each sample were compared with one another. From the test results, it was observed that mechanical properties of the block and piston samples were more reliable than those of tube samples. But it was observed that the water content of piston was similar to that of tube samples at given depths while the water content of block samples was 14.3∼15.8% smaller than that of piston and tube samples. In addition to the evaluation of the quality of samples, relationship between c/sub u// σ/sub vc/'and OCR was established from the results of the CK/sub o/U triaxial compression tests, which were carried out using SHANSEP method. And also undrained shear strength was analyzed using the in-situ test data such as Cone Penetration Test(CPT), Dilatometer Test(DMT), and Field Vane Test(FVT) and was compared with that evaluated from CK/sub o/U triaxial compression test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.10a
• /
• pp.429-436
• /
• 2005

In this study, we have compared with the differences between the extent of sampling disturbance and consolidation characteristics by experiments, which are consolidation test and have been performed with Kwang-Yang clay samples. The effects on sampling disturbance to consolidation characteristics of soft clay have been inverstigated by using soil samples obtained from large block sampling and piston sampling methods. Through a few experiments, we've got important results which are that the consoilidation parameter of large block sample(Pc, Cc, Cv) is much larger than the value of parameter of piston sample. We've also found the fact that the large block sample using the large size sampler is much better than piston sample in the quality of goods to lessen the effects on disturbance of sampling. When compared to the parameter of consolidation along with the methods of experiment, we found that the result performed by large size consolidation test is the greatest one and CRS is much better than standard consolidation test to seek for proper parameter.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.37 no.5
• /
• pp.115-123
• /
• 2000

In this paper, a block FIR(Finite Impulse Response) filtering architecture is proposed for IF digital down converter. Digital down converter consists of digital mixers. decimation filters and down samplers. In this proposed structure, it is shown that a efficient parallel decimation filter architecture can be produced by cancellation of inherent up sampling of the block filter and following down sampler Furthermore. it is shown that computational complexity of the proposed architecture is reduced by exploiting the block FIR structure and zero values of the digital mixers.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.95-102
• /
• 1999

It is important to estimate the magnitude of settlement and the time of primary consolidation in geotechnical engineering projects. For these purposes, site explorations and laboratory tests are usually performed. However, the mechanical properties determined from laboratory tests on the samples obtained by different sampling techniques show different trends. In this study, three types of consolidation test were carried out on the soil samples obtained by three different sampling techniques (76mm tube, 76mm piston, and block samples), to verify the effect of sample disturbance on consolidation properties. It was found that sampling methods have influence on the $\varepsilon$ - log $\sigma$'$_{v}$ relationship. While insignificant difference of compression indices from the samples obtained by different sampling techniques was observed in compression region, these values showed a different trend in precompression region. The values of $c_{v}$ and k of block samples had a tendency to be larger than those of piston and tube samples. At consolidation pressure larger than $\sigma$'$_{p}$, however, these properties became similar regardless of sampling methods. The block and piston samples gave slightly higher values of $C_{a/}$ $C_{c}$ than tube samples. In the results of I $L_{EOP}$ and CRS test, it was observed that the values of $\sigma$'$_{p measured}$/$\sigma$'$_{p best estimated}$ of Yang-San clay decreases when strain becomes larger than 1.0% and that precompression strain of block samples is in the range of 1.5~2.0% while those of piston and tube samples are 1.75~3.75%. It was also shown that the values of $\sigma$'$_{p}$ of block samples exceed those of piston and tube samples by about 6~10%.6~10%.%.%.%.%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.13-13
• /
• 2009

본 연구는 MLCC 구성성분의 증발/비등에 의한 저분자물질의 제거가 bar 수축에 미치는 영향도를 평가하기 위해, 압착 bar에서 발생하는 고농도의 out gas를 정량하기 위한 최적 system을 구축하고자 하였다. gas 포집에 범용적으로 사용하는 Purge & Trap sampler 대신 Heating block를 사용하여 gas를 발생시키고 동시에 solvent에 용해시킴으로써 고농도의 시료가 희석될 수 있는 전처리 장치를 디자인하였다. 그 결과 고농도 gas 주입에 의한 장비오염과 peak saturation 문제가 해결되었고, gas phase의 시료를 liquid phase로 상전이 시켜 autosampler를 이용한 정확한 량의 시료 주입이 가능하였다. System의 Gage Linearity와 Bias는 각각 1.7%와 1.3%로 개선이 필요없는 수준의 정확도를 가졌다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.177-178
• /
• 2013

Steel structures of the seaside area are naturally led to surface corrosion due to incoming salt. Signature measures for this are to replace steel with steel material with a high corrosion-resistance and to block salt and other deteriorative factors beforehand through finishing work such as surface coating. However, the variety in steel materials, finishing type, and construction methods makes adhesive weight of incoming salt different depending on each type. For this research, measurement results derived from an enhancement experiment on artificial incoming salt adhesive to 4 steel finishing types and 2 material types identified a difference of adhesive weight by each sampler.