• Proceedings of the Korean Vacuum Society Conference
• /
• 2009.02a
• /
• pp.131.2-131.2
• /
• 2009

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.57-58
• /
• 2006

As the power density and switching frequency increase, thermal analysis of power electronics system becomes imperative. The analysis provides valuable information on the semiconductor rating, long-term reliability. In this paper, thermal distribution of the Non Punchthrough(NPT) Insulated Gate Bipolar Transistor has been studied. For analysis of thermal distribution, we obtained results by using finite element simulator, Ansys and thermal distributions form experiments.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.4
• /
• pp.601-605
• /
• 2012

Insulated Gate Bipolar Transistors(IGBTs) have received wide attention because of their high current conduction and good switching characteristics. To reduce the power loss of IGBT, the onstate voltage drop should be lowered and the switching time should be shortened. However, there is trade-off between the breakdown voltage and the on-state voltage drop. The FLoatingIsland(FLI) structure can lower the on-state voltage drop without reducing breakdown voltage. In this paper, The FLI IGBT shows an on-state voltage drop that is 22.5% lower than the conventional IGBT, even though the breakdown voltages of each IGBT are almost identical.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.815-818
• /
• 1998

The Insulated Gate Bipolar Transistor has the characteristics of MOSFET and BJT. The characteristics of proposed device exhibit high speed switching, the voltage controlled property, and the low ON resistance. This hybrid device has been used and developed continuously in the power electronic engineering field. We can simulate many IGBT circuits, such as the motor drive circuit, the switching circuits etc, with PSpice. However, some problems in PSpice is that the IGBT is old-fashioned and is very difficult to get it. In this paper, the IGBT in PSpice is considered as the basic structure. We changed the valuse of base width, gate-drain overlaping area, device area, and doping concentration, then calculated MOS transconductance, ambipolar recombination lifetime etc. Using this resultant parameter, we could predict the transient response characteristicsof IGBT, for examplex, voltage overshoot, the rising curve of voltage, and the falling curve of current.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.857-860
• /
• 1991

This paper describes a High-Speed 8-bit Current-Mode BiCMOS A/D Converter. The characteristics of this A/D Converter are as fellows. First, as ADC is operating in current-mode we can obtain the properties of increase of converting speed, low noise, and wideband. Second, the properties of high switching speed in bipolar transistor and of high packing density, low power consumption in MOS trnsistor are combined. Finally we reduce chip area by designing it with subranging mode and improve the converting speed by performing subtraction directly, which doesn't need D/A convertings, using current switching element. This converter is composed of two 4-bit ADC, current soure array which provides signal and reference current, current comparator and encoding network.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.627-630
• /
• 1991

This study is about vector controlled inverter for high quality elevator drive that is to improve the settling accuracy of elevator car and passenger's comfort in commercial buildings. In this study, an instantaneous space vector control type inverter was used to reduce the torque ripple ant to improve the velocity follow-up. This method calculates Instantaneous actual output torque and flux of induction motor by voltage and current, then compares them with a reference values by a speed regulator. The outputs of comparators select a switching mode, for an optimal voltage vector. Also, this study used IGBT (Insulated Gate Bipolar-Transistor), a high speed switching element, to reduce sound noise level, and DSP (Digital Signal Processor) was used to improve the reliability of the control circuit by fully digitalization.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.338-340
• /
• 2001

Power factor improved for single-phase buck-converter is studied in the paper. To sinusoidal waveform the input current with a near-unity power factor over a wide variety of operating conditions, the output capacitor is operated with voltage reversibility for the supply by arranging the auxiliary diode and power switching device. Then the output voltage is superposed on the input voltage during on time duration of power switching devices in order to minimize the input current distortion caused by the small input voltage when changing the polarity. The tested setup, using two insulated gate bipolar transistors(IGBT) and a microcomputer, is implemented and IGBT are switched with 20[kHz], which is out of the audible band. Moreover, a rigorous state-space analysis is introduced to predict the operation of the rectifier. The simulated results confirm that the input current can be sinusoidal waveform with a near-unity power factor and a satisfactory output voltage regulation can be achieved.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1438-1444
• /
• 2007

Standard Gate Turn Off (GTO) Thyristor drive technology results in inhomogeneous turn-on and turn-off transients which in turn needs costly dv/dt and di/dt snubber circuits. Added to this GTO is bulky in size, needs external cooling, slower switching time etc. The development of high voltage Insulated Gate Bipolar Transistor (IGBT) have given new device advantage in the areas where they compete with conventional GTO technology. Indian Railway has developed first IGBT based traction converter and was commissioned in November 2006. Some of the supremacy of IGBT are smaller in size, no external cooling is required, built in power supply which enhances reliability, lower switching losses which leads to higher efficiency, reduced gate drive, high frequency operation in real time etc. These advantages are highlighted along with IGBT Traction system in operation.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.1011-1015
• /
• 2005

Fully digital controlled 20-bit magnet power supplies have been developed and successfully tested for closed orbit correction of PLS(Pohang Light Source). The new digital power supply has used fiber optics for 25kHz switching of IGBT drivers, and implemented DSP, ADC, Interlock, DCCT cards in a compact 3U-sized 19" chassis. Input/Output low-pass filters suppress harmonics of 60Hz line frequency and switching frequency noise effectively. Overall performance of the power supplies have been demonstrated as +/- 2ppm short-term stability(<1 min), and +/- 10ppm long-term stability(<36 hours). All the existing 12-bit 70 power supplies for vertical correction magnets will be replaced with new digital power supplies during 2005 summer shutdown period. In this paper, we will describe the hardware structure and control method of the digital power supply and the experimental results will be shown.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.522-531
• /
• 2016

This paper proposes a new NLC (Nearest Level Control) scheme for MMCs (Modular Multilevel Converters), which offers voltage ripple reductions in the DC capacitor of the SM (Sub-Module), the output voltage harmonics, and the switching losses. The feasibility of the proposed NLC was verified through computer simulations. Based on these simulation results, a hardware prototype of a 10kVA, DC-1000V MMC was manufactured in the lab. Experiments were conducted to verify the feasibility of the proposed NLC in an actual hardware environment. The experimental results were consistent with the results obtained from the computer simulations.