• Korean Chemical Engineering Research
• /
• 제60권1호
• /
• pp.86-92
• /
• 2022

최근 COVID-19 팬데믹 등 다양한 이유로 인해 바이오 헬스케어 시장이 전세계적으로 활성화되고 있다. 그 중, 생체정보 측정 및 분석 기술은 앞으로의 기술적 혁신성과 사회경제적 파급효과를 불러일으킬 것으로 예측된다. 기존의 시스템은 생체 신호를 받아 신호 처리를 하는 과정에서 신호 송×수신부, 운영체제, 센서, 그리고 인터페이스를 구동하기 위한 대용량 배터리를 필수적으로 요구한다. 하지만, 배터리 용량의 한계가 인해 시×공간적인 기기 사용의 제한을 야기하며, 이는 사용자의 헬스케어 모니터링에 필요한 데이터의 단절에 대한 원인으로 작용할 수 있으므로 헬스케어 디바이스의 큰 걸림돌 중의 하나이다. 본 연구에서는 생체정보 측정 장치에 접촉대전 효과(Triboelectric effects)와 전자기유도 효과(Electro-magnetic effects)를 융합하여, 외부 전원을 요구하지 않는 독립 구동이 가능한 시스템을 구성하여 시×공간적으로 사용 제한이 없는 소형 생체정보 측정 모듈을 설계 및 검증했다. 특히, 다양한 헬스케어 모니터링 중 족압 계측을 통해 사용자의 보행 습관 등을 파악할 수 있는 무선 족압 계측 모니터링 시스템을 검증했다. 보행 시 발생하는 접촉×분리 움직임에서 접촉대전 효과를 이용한 효과적인 압력 센서와 압력에 따른 전기적 출력신호를 통해 족압 센서를 만들고, 축전기를 이용한 신호처리 회로를 통해 이의 동적 거동을 계측할 수 있다. 또한, 출력된 전기신호의 무선 송×수신용 전원으로 사용하기 위해 전자기 유도 효과를 이용하여 보행 시 생기는 생체역학적 에너지를 전기에너지로 수확했다. 따라서, 이번 연구는 사용자가 제한적인 배터리 용량 때문에 생기는 충전에 대한 불편함을 줄일 수 있고, 뿐만 아니라 데이터 단절에 대한 문제점을 극복할 수 있는 방법으로서 큰 잠재력을 보여줌을 시사한다.

• 대한치과보철학회지
• /
• 제40권5호
• /
• pp.507-524
• /
• 2002

Load transfer of implant overdenture varies depending on anchorage systems that are the design of the superstructure and substructure and the choice of attachment. Overload by using improper anchorage system not only will cause fracture of the framework or screw but also may cause failure of osseointegration. Choosing anchorage system in making prosthesis, therefore, can be considered to be one of the most important factors that affect long-term success of implant treatment. In this study, in order to determine the effect of anchorage systems on load transfer in mandibular implant overdenture in which 4 implants were placed in the interforaminal region, patterns of stress distribution in implant supporting bone in case of unilateral vertical loading on mandibular left first molar were compared each other according to various types of anchorage system using three-dimensional photoelastic stress analysis. The five photoelastic overdenture models utilizing Hader bar without cantilever using clips(type 1), cantilevered Hader bar using clips(type 2), cantilevered Hader bar with milled surface using clips(type 3), cantilevered milled-bar using swivel-latchs and frictional pins(type 4), and Hader bar using clip and ERA attachments(type 5), and one cantilevered fixed-detachable prosthesis(type 6) model as control were fabricated. The following conclusions were drawn within the limitations of this study, 1. In all experimental models. the highest stress was concentrated on the most distal implant supporting bone on loaded side. 2. Maximum fringe orders on ipsilateral distal implant supporting bone in a ascending order is as follows: type 5, type 1, type 4, type 2 and type 3, and type 6. 3. Regardless of anchorage systems. more or less stresses were generated on the residual ridge under distal extension base of all overdenture models. To summarize the above mentioned results, in case of the patients with unfavorable biomechanical conditions such as not sufficient number of supporting implants, short length of the implant and unfavorable antero-posterior spread. selecting resilient type attachment or minimizing distal cantilever bar is considered to be appropriate methods to prevent overloading on implants by reducing cantilever effect and gaining more support from the distal residual ridge.

• 대한의용생체공학회:의공학회지
• /
• 제28권3호
• /
• pp.397-409
• /
• 2007

Owing to needs of biomechanical comprehension and analysis to obtain various medical treatment designs which are related with the spine in order to cure and diagnose LBP patients, the FE modeling and nonlinear analysis of lumbosacrum including a partial ilium and iliolumbar ligaments, were carried out. First, we investigated whether the geometrical configuration of vertebrae displayed by DICOM slice files is regular and normal condition. After constructing spinal vertebrae including a partial ilium, a sacrum and five lumbars (from L1 to L5)with anatomical shape reconstructed using softwares such as image modeler and CAD modeler, we added iliolumbar ligaments, lumbar ligaments, discs and facet joints, etc.. And also, we assigned material property and discretized the model using proper finite element types, thus it was completely modeled through the above procedure. For the verification of each segment, average sagittal ROM, average coronal ROM and average transversal ROM under various loading conditions(${\pm}10Nm$), average vertical displacement under compression(400N), ALL(Anterior Longitudinal Ligament) and PLL(Posterior Longitudinal Ligament) force at L12 level, strains of seven ligaments on sagittal plane at L45 level and maximal strain of disc fibers according to various loading conditions at L45 level, etc., they were compared with experimental results. For the verification of multilevel-lumbosacrum spine including partial ilium and iliolumbar ligaments, the cases with and without iliolumbar ligaments were compared with ROM of experiment. The results were obtained from analysis of the verified FE model as follows: I) Iliolumbar ligaments played a stabilizing role as mainly posterior iliolumbar ligaments under flexion and as both posterior and anterior iliolumbar ligaments of one side under lateral bending. 2) The iliolumbar ligaments decreased total ROM of 1-8% in total model according to various motion conditions, which changed facet contact forces of L5S level by approximately 0.8-1.4 times and disc forces of L5S level by approximately 0.8-1.5 times more than casewithout ilioligaments, under various loading conditions. 3) The force of lower discs such as L45 and L5S was bigger than upper discs under flexion, left and right bending and left and right twisting, except extension. 4) It was predicted that strains of posterior ligaments among iliolumbar ligaments would produce the maximum 16% under flexion and the maximum 10% under twisting. 5) It's expected that this present model applies to the development and design of artificial disc, since it was comparatively in agreement with the experimental datum.

• The Journal of Advanced Prosthodontics
• /
• 제9권5호
• /
• pp.371-380
• /
• 2017

PURPOSE. The aim of this study is to evaluate and compare the stress distribution in Locator attachments in mandibular two-implant overdentures according to implant locations and different loading conditions. MATERIALS AND METHODS. Four three-dimensional finite element models were created, simulating two osseointegrated implants in the mandible to support two Locator attachments and an overdenture. The models simulated an overdenture with implants located in the position of the level of lateral incisors, canines, second premolars, and crossed implant. A 150 N vertical unilateral and bilateral load was applied at different locations and 40 N was also applied when combined with anterior load at the midline. Data for von Mises stresses in the abutment (matrix) of the attachment and the plastic insert (patrix) of the attachment were produced numerically, color-coded, and compared between the models for attachments and loading conditions. RESULTS. Regardless of the load, the greatest stress values were recorded in the overdenture attachments with implants at lateral incisor locations. In all models and load conditions, the attachment abutment (matrix) withstood a much greater stress than the insert plastic (patrix). Regardless of the model, when a unilateral load was applied, the load side Locator attachments recorded a much higher stress compared to the contralateral side. However, with load bilateral posterior alone or combined at midline load, the stress distribution was more symmetrical. The stress is distributed primarily in the occlusal and lateral surface of the insert plastic patrix and threadless area of the abutment (matrix). CONCLUSION. The overdenture model with lateral incisor level implants is the worst design in terms of biomechanical environment for the attachment components. The bilateral load in general favors a more uniform stress distribution in both attachments compared to a much greater stress registered with unilateral load in the load side attachments. Regardless of the implant positions and the occlusal load application site, the stress transferred to the insert plastic is much lower than that registered in the abutment.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1997년도 추계학술대회
• /
• pp.511-514
• /
• 1997

The objective of this study is to propose a finite element based design of the dental implant replacing unction and shape of natural teeth. For this, geometric actors were varied to investigate stress distribution of the alveolar bone around dental implant. In this study, the results were obtained based on the theory of linear elastic, with geometrically axisymmetric assumption. Geometric actors determining implant shape are ranged as 0.2mm-0.6mm, 0.04mm-0.1mm, 0.46mm-0.84mm or height of thread, radius of curvature of thread, and pitch, respectively. The stresses in the alveolar bone caused by biting force playa major role in determining implant stability. Especially, the stress concentration in the cortical bone causes bone resorption and finally makes the implant unstable. Therefore, the stress distributions were investigated on the side of the alveolar bone focusing on the area of cortical bone. The maximum von Mises stress was found to increase up to 6% as the height of thread increases, while its value was to decrease to 19% when the radius of curvature increase within the assigned ranges. For the variation of pitch, the larger size of pitch results in greater maximum von Mises stress when the length of the implant under consideration is fixed. The existence of the neck below the shoulder did not affect the stress distribution in the region of alveolar bone. However, the stresses on the side of the implant near the neck were found to be different by 20% approximately. Therefore, the neck can provide the stability of the implant against continuing biting movement. As a conclusion, the finite element based study shows a potential in designing the dental implant systematically.

• 대한치과교정학회지
• /
• 제41권5호
• /
• pp.354-360
• /
• 2011

Objective: To investigate the effects of different pilot-drilling methods on the biomechanical stability of self-tapping mini-implant systems at the time of placement in and removal from artificial bone blocks. Methods: Two types of artificial bone blocks (2-mm and 4-mm, 102-pounds per cubic foot [102-PCF] polyurethane foam layered over 100-mm, 40-PCF polyurethane foam) were custom-fabricated. Eight mini-implants were placed using the conventional motor-driven pilot-drilling method and another 8 mini-implants were placed using a novel manual pilot-drilling method (using a manual drill) within each of the 2-mm and 4-mm layered blocks. The maximum torque values at insertion and removal of the mini-implants were measured, and the total energy was calculated. The data were statistically analyzed using linear regression analysis. Results: The maximum insertion torque was similar regardless of block thickness or pilot-drilling method. Regardless of the pilot-drilling method, the maximum removal torque for the 4-mm block was statistically higher than that for the 2-mm block. For a given block, the total energy at both insertion and removal of the mini-implant for the manual pilot-drilling method were statistically higher than those for the motor-driven pilot-drilling method. Further, the total energies at removal for the 2-mm block was higher than that for the 4-mm block, but the energies at insertion were not influenced by the type of bone blocks. Conclusions: During the insertion and removal of mini-implants in artificial bone blocks, the effect of the manual pilot-drilling method on energy usage was similar to that of the conventional, motor-driven pilot-drilling method.

• 대한의용생체공학회:의공학회지
• /
• 제25권6호
• /
• pp.531-536
• /
• 2004

외고정장치를 이용한 골절 치료에서, 골절 부위에서의 절골편간 운동은 골절의 치유과정에 다양한 영향을 미친다고 알려져 있고, 이 미세 운동은 외고정장치-절골편 시스템의 강성과 밀접한 관련이 있다. 그렇기 때문에 최적의 골절 치유 과정을 부여하기 위하여 외고정장치 시스템의 구성 인자와 강성과의 연관성에 대한 이해가 필요하다. 본 연구에서는 장골 골절의 외고정술에 대한 유한요소 해석에서 외고정장치 시스템의 구성인자가 시스템 강성에 미치는 영향을 조사하였다. 이를 위하여, 시스템 정렬, 재료 비선형성, 조인트 유연성 및 가골형성 등을 해석 인자로 선정하였다. 개발된 유한요소 모델은 실험 결과와 유사한 시스템 강성을 나타내었고, 조인트 유연성 및 재료 비선형성의 고려는 시스템 강성 결과를 더욱 정확하게 반영하였다. 시스템 비정렬상태, 조인트 유연성 및 재료 비선형성은 시스템 강성의 감소를, 그리고 골절 부위의 가골형성은 시스템 강성의 증가를 나타내었다. 본 연구 결과는 외고정술시 시스템 강성을 증가시키기 위한 프레임 구성이나 기구 설계 등의 도구로 사용될 수 있을 것으로 기대된다.

• 구강회복응용과학지
• /
• 제37권1호
• /
• pp.48-60
• /
• 2021

치아의 병적 이동으로 전치가 정출되고 수직 피개가 깊은 치주염 환자에서는 치주 염증 치료와 더불어 정출된 전치의 위치 개선이 필요하다. 그러나 깊은 수직 피개로 교정 장치 부착이 어렵고, 역학적으로 전치 압하보다 구치 정출이 더욱 쉽게 발생하는 문제점이 있다. 특히 골격적 장안모를 보이는 환자에서 구치 정출을 통한 상대적 전치 압하는 안모의 악화를 야기하므로, 치료 계획에서부터 이를 차단하기 위한 설계가 필요하다. 본 증례에서는 전치가 정출되어 과개 교합을 보이는 치주염 환자에서, 철저한 치주 치료와 하악 전치에 부착한 cute bracket과 골성 고정원을 이용한 고정원 보강으로 하악 전치의 양호한 압하 치료 결과를 얻을 수 있었으며, 8년간 경과 관찰하여 이를 보고하고자 한다.

• 대한치과보철학회지
• /
• 제53권2호
• /
• pp.120-127
• /
• 2015

목적: 4종의 임플란트 나사산이 골유착 중간과정과 완료 이후 단계에서 보이는 응력분산 특성을 평가하고자 한다. 재료 및 방법: 실린더형 몸체(외경 4.1 mm 길이 10 mm)에 이전연구에서 식립 특성이 우수하게 평가되었던 V-자형 나사산과 다른 3종(buttress형, reverse buttress형, square형)의 나사산을 가진 4종의 임플란트가 악골에 매식된 복합체 모델을 CAD 프로그램으로 제작하였다. 지대주 상부에 100 N의 힘을 임플란트 장축과 30도 방향으로 부하하고 인접골 응력분포를 유한요소 해석하였다. 응력분산 특성이 골유착 진척 상태에 따라 달라질 수 있다는 가정하에 임플란트/골 계면을 골유착 미숙단계와 골유착 완료단계의 두 가지로 구분하여 분석하였다. 골유착 미숙단계는 임플란트/골 계면을 비선형 contact 조건(마찰계수 0.3)으로 모사하였고, 골유착이 완료된 단계에 대해서는 계면이 충분히 결합된 것으로 간주하여 접합(bonding) 조건을 부여하였다. 결과: 골유착 정도에 따라 임플란트의 응력분산 특성이 달라졌다. 골유착 미숙단계에서는 골응력과 나사산에 따른 응력 특성의 차이도 상대적으로 컸고 골유착 완료단계에서는 골응력의 절대값과 나사산간 차이가 모두 감소하였으며, V-자형 나사산의 응력분산 특성은 골유착 미숙 및 완료단계에서 모두 4종 나사산의 중간 정도였다. 이로부터 나사산 디자인의 차이는 임플란트 식립후 골유착이 진행되는 과정까지 영향을 미치며, 일단 골유착이 완료되면 나사산의 영향은 급격히 감소할 것임을 추론할 수 있었다. 결론: V-자형 나사산의 응력분산 특성은 골유착이 이루어지는 단계와 완료된 이후 단계 전기간 동안 4종 나사산의 중간 정도였다.

• 대한치과보철학회지
• /
• 제46권3호
• /
• pp.290-297
• /
• 2008

STATEMENT OF PROBLEM: Implant-supported fixed cantilever prostheses are influenced by various biomechanical factors. The information that shows the effect of implant number and position of cantilever on stress in the supporting bone is limited. PURPOSE: The purpose of this study was to investigate the effect of implant number variation and the effect of 2 different cantilever types on stress distribution in the supporting bone, using 3-dimensional finite element analysis. MATERIAL AND METHODS: A 3-D FE model of a mandibular section of bone with a missing second premolar, first molar, and second molar was developed. $4.1{\times}10$ mm screw-type dental implant was selected. 4.0 mm height solid abutments were fixed over all implant fixtures. Type III gold alloy was selected for implant-supported fixed prostheses. For mesial cantilever test, model 1-1 which has three $4.1{\times}10$ mm implants and fixed prosthesis with no pontic, model 1-2 which has two $4.1{\times}10$ mm implants and fixed prosthesis with a central pontic and model 1-3 which has two $4.1{\times}10$ mm implants and fixed prosthesis with mesial cantilever were simulated. And then, 155N oblique force was applied to the buccal cusp of second premolar. For distal cantilever test, model 2-1 which has three $4.1{\times}10$ mm implants and fixed prosthesis with no pontic, model 2-2 which has two $4.1{\times}10$ mm implants and fixed prosthesis with a central pontic and model 2-3 which has two $4.1{\times}10$ mm implants and fixed prosthesis with distal cantilever were simulated. And then, 206N oblique force was applied to the buccal cusp of second premolar. The implant and superstructure were simulated in finite element software(Pro/Engineer wildfire 2.0). The stress values were observed with the maximum von Mises stresses. RESULTS: Among the models without a cantilever, model 1-1 and 2-1 which had three implants, showed lower stress than model 1-2 and 2-2 which had two implants. Although model 2-1 was applied with 206N, it showed lower stress than model 1-2 which was applied with 155N. In models that implant positions of models were same, the amount of applied occlusal load largely influenced the maximum von Mises stress. Model 1-1, 1-2 and 1-3, which were loaded with 155N, showed less stress than corresponding model 2-1, 2-2 and 2- 3 which were loaded with 206N. For the same number of implants, the existence of a cantilever induced the obvious increase of maximum stress. Model 1-3 and 2-3 which had a cantilever, showed much higher stress than the others which had no cantilever. In all models, the von Mises stresses were concentrated at the cortical bone around the cervical region of the implants. Meanwhile, in model 1-1, 1-2 and 1-3, which were loaded on second premolar position, the first premolar participated in stress distribution. First premolars of model 2-1, 2-2 and 2-3 did not participate in stress distribution. CONCLUSION: 1. The more implants supported, the less stress was induced, regardless of applied occlusal loads. 2. The maximum von Mises stress in the bone of the implant-supported three unit fixed dental prosthesis with a mesial cantilever was 1.38 times that with a central pontic. The maximum von Mises stress in the bone of the implant-supported three-unit fixed dental prosthesis with a distal cantilever was 1.59 times that with a central pontic. 3. A distal cantilever induced larger stress in the bone than a mesial cantilever. 4. A adjacent tooth which contacts implant-supported fixed prosthesis participated in the stress distribution.