• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.1035-1040
• /
• 2001

The effects of polymer-binder ratio and slag content on the properties of combined wet/dry-cured polymer-modified mortars using granulated blast-furnace slag (slag) are examined. As a result, the flexural and compressive strengths of polymer-modified mortar using slag reaches a maximum at a slag content of 40%, and is inclined to increase with increasing polymer-binder ratio. The water absorption, carbonation depth and chloride ion penetration depth tend to decrease with increasing polymer-binder ratio and slag content.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.803-806
• /
• 2005

The effect of coating method and binder content on the tensile adhesion strength, water absorption and cl- penetration depth of polymer-modified pastes using redispersible polymer powders and ceramic powder are examined. As a result, the tensile adhesion strength of the polymer-modified pastes tend to increase with increasing binder content and: number of coating. The water absorption and cl- penetration depth of the polymer-modified pastes tend to decrease with increasing binder content and number of coating.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 봄학술 발표회 논문집(II)
• /
• pp.73-76
• /
• 2005

This study aims to suggest a simple and convenient design for a mix proportion method for high performance concrete by determining the optimum fine aggregate ratio and minimum binder content based on the maximum density theory. The mix design method introduced in this study adopted the optimum fine aggregate ratio with a minimum void and binder content higher than the minimum binder content level. The research results reveal that the method helps to reduce trial and error in the mixing process and is a convenient way of producing high performance concrete with self filler ability. In an experiment based on the mix proportion method, when aggregate with the fine aggregation ratio of 41$\%$ was used, the minimum binder content of high performance concrete was 470kg/$m^{3}$ and maximum aggregate capacity was $0.657m^{3}/m^{3}$. In addition, in mixing high performance concrete, the optimal slump flow to meet filler ability was 65$\pm$5cm, V load flow speed ranged from 0.5 to 1.5.

• 유기물자원화
• /
• 제12권4호
• /
• pp.95-104
• /
• 2004

본 연구에서는 가연성 건설폐기물 재활용의 일환으로, 폐발포폴리스티렌의 스티렌 용액에 가교제 및 개시제를 첨가하여 제조한 결합재와, 폐목재 칩을 이용하여, 폐목재-플라스틱 복합패널을 제조하였다. 전열 프레스를 이용하여 다양한 결합재량 및 충전재-결합재 비를 갖는 복합패널 공시체를 제조하였으며, 그 겉보기 밀도, 흡수율, 흡수에 의한 팽창률, 휨강도, 내수성 등에 관한 일련의 실험을 행하였다. 폐목재-플라스틱 복합패널의 겉보기밀도는 결합재량 및 충전재-결합재비의 증가에 따라 증대하며, 그 휨강도 및 습윤 휨강도는, 결합재량 35%, 충전재-결합재비 0.8에 있어서 최대치에 이른다. 흡수율 및 흡수에 의한 두께 팽창률은, 결합재량 및 충전재-결합재비의 증가에 따라 현저하게 감소한다. 결합재량 30%이상의 경우, 충전재-결합재비에 관계없이, 복합패널의 24h 상온 수중($20^{\circ}C$) 침지 및 2h 끓는 물중($100^{\circ}C$)＋1h상온 수중($20^{\circ}C$) 침지에 의한 휨강도의 감소는 거의 발생하지 않으며, 높은 내수성을 발현한다.

• Elastomers and Composites
• /
• 제29권5호
• /
• pp.431-435
• /
• 1994

For recycling of the waste tires, polyurethane binder mixed with the scrapped rubber powders which obtained from tread part of waste tire. This study covered the effect of the binder contents on the mechanical properties of the blend. We also studied the change of the properties after aging on properties compared with those of before aging. The curing reaction of the binder was also investigated in this study. We obtained conclusions the suitable binder content was 15phr in this system.

• 한국세라믹학회지
• /
• 제29권3호
• /
• pp.241-251
• /
• 1992

The effects of slip composition and processing conditions on the fabrication of ceramic heat exchanger cores by doctor blade process were investigated. Since the effects of those two variables were inter-dependent, the effects of binder system, binder plus plasticizer, were extensively studied for a limited range of processing conditions and a pre-determined ceramic composition. The content of binder system and the ratio of binder to plasticizer were identified as main variables to affect densities and mechanical properties of green sheets, compressive properties and bond strengths of laminates, and shrinkages and their anisotropy of sintered laminates. However, sintered densities and water absorptions of laminates were not influenced by either the content of binder system or the ratio of binder to plasticizer, when the debinded laminates had a relatively high density (relative density of >55% in this study).

• 한국분말재료학회지
• /
• 제5권4호
• /
• pp.286-292
• /
• 1998

Ni$_3$Al intermetallic compound has been tested as a binder phase, in order to improve the oxidation resistance and the mechanical properties of TiC-Ni cermet at a high temperature. The wettability of $Ni_3Al$ on TiC and the optimum sintering condition were investigated in TiC-(30, 40) vol% $Ni_3Al$ cermets with the sintering temperature (1380~$1430^{\circ}C$) and time (30~99 min). The results are summarized as follows: 1) Ni$_3$Al showed good wettability on TiC above 1400$^{\circ}C$ ; 2) The shrinkages of the specimens increased with the sintering temperature, the sintering time and the binder content, whereas the relative densities were decreased; 3) Any other phase did not appeared in the microstructures of all sintered cermets. The grain sizes of TiC became larger as the sintering temperature and the sintering time as well as the binder content increased; 4) The hardness of the cermets decreased with increase in the sintering temperature and the sintering time as well as the binder content; 5) The transverse-rupture strength of the cermets increased with the sintering temperature and the sintering time, whereas it decreased with the binder content.

• 한국세라믹학회지
• /
• 제27권3호
• /
• pp.355-360
• /
• 1990

One of the possible ways to make a flexible wire of high-Tc superconductiong ceramics is the extrusion of a mixture slurry of superconducting powder with an appropriate polymer binder. The fabrication procedure for $YBa_2Cu_3O_{7-{\delta}}$ superconducting coils with this plastic mass is described. The major factors limiting the formation of extruded wire are the binder content, powder size, and entrapped gas in the mixture slurries. The optimum content of binder for both good flexbility and strength of wire was estimated to be 30wt%. The finer the powder size is, the more homogeneous structure the extruded wire has. The vacuum degassing before extrusion was necessary to remove the entrapped gas in as-extruded wire. The formability of wire depends greatly on the wire radius and binder content. After burning out the binder and the successive sintering, the contacts between the superconducting grains could be made. The resistivity vs. temperature behavior measured in the final wire showed the transition temperature of 90K with narrow transition width. However, the critical current densities of these wires are much lower in comparison to those of conventional bulk specimens.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.799-802
• /
• 2005

The effects of binder content and ceramic powder content on the water absorption, carbonation depth and cl- penetration depth of polymer-modified pastes using redispersible polymer powders and ceramic powder are examined. As a result, the water absorption .of the polymer-modified pastes using redispersible polymer powders tend to decrease with increasing binder content and ceramic powder content. Regardless of the type of redispersible polymer powder, the carbonation depth and cl- penetration depth of the polymer-modified pastes with ceramic powder tend to decrease with increasing binder content and ceramic powder content.

• 한국도로학회논문집
• /
• 제14권4호
• /
• pp.51-61
• /
• 2012

PURPOSES : This study deals with the working life of polymer concrete, which is typically used as a repair or overlay material for portland cement concrete pavements. METHODS : In the scope of this study, laboratory testing was conducted on fresh MMA modified UP polymer concrete, which uses an MMA monomer for viscosity adjustment and strength improvement of UP resin. The experimental variables were temperature (-20 to $+20^{\circ}C$) and binder components (MMA, MEKPO, and DMA). RESULTS : The result showed that the optimum binder ratios for polymer concrete production were 12, 11, and 10 wt.% when the MMA contents were 20, 30, and 40 wt.%, respectively. The working life of polymer concrete depending on temperature and binder components could be expressed by a logarithmic functional formula. The coefficient of variation for each binder component was the highest for DMA content while the lowest for MEKPO content. Also, the contents of each binder component for ensuring the working life of 60 minutes were proposed. CONCLUSIONS : Ultimately, the present study derived a linear regression equation estimating 60 minutes working life based on the setting times of each binder component.