• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04b
• /
• pp.3-5
• /
• 2008

The $SrBi_2Ta_2O_9$ thin films are deposited on Pt-coated electrode(Pt/$TiO_2/SiO_2$/Si) using RF magnetron sputtering method. The ferroelectric properties of SBT capacitors with annealing temperatures were studied. Through the x-ray diffraction analysis and the scanning electron microscopy (SEM), it could be observed that crystallization of the SBT thin film started around $650^{\circ}C$ and complete crystallization was accomplished around $750^{\circ}C$ and grains grew from a small spheric form to rod-like. For the leakage current density of the SBT capacitor depending upon various annealing atmospheres, capacitor annealed in the oxygen atmosphere showed the most excellent characteristic, and they were respectively about $2.13\times10^{-9}[A/cm^2]$ at 5V and 340.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.277-278
• /
• 2007

In this study, in order to develop multilayer piezo-actuator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3,\;Na_2CO_3$, ZnO as sintering aids and their piezoelectric and dielectric properties were investigated according to the Bi substitution. Bi substitution enhanced electromechanical coupling factor$(k_p)$ and dielectric constant$({\varepsilon}_r)$. However, mechanical quality factor was deteriorated. At the sintering temperature of $870^{\circ}C$ and Bi substitution of 1mol%, density, electromechanical coupling factor$(k_p)$, mechanical quality factor$(Q_m)$, Dielectric constant$({\varepsilon}_r)$ and piezoelectric constant$(d_{33})$ of specimen showed the optimum value of $7.878g/cm^3$, 0.608, 835, 1603 and 397pC/N, respectively.

• Journal of Pharmacopuncture
• /
• v.18 no.1
• /
• pp.63-71
• /
• 2015

Objectives: This study was carried out to analyze the single-dose toxicity of Eun-Bi San pharmacopuncture injected into the muscle of Sprague-Dawley (SD) rats. Methods: All experiments were performed at Biotoxtech, an institution certified to conduct non-clinical studies under the Good Laboratory Practice (GLP) regulations. Six week old SD rats reared by ORIENTBIO were chosen for this pilot study. The reason SD rats were chosen is that they have been widely used in safety tests in the field of medicine, so the results can be easily compared with many other databases. The Eun-Bi San pharmacopuncture was made in a clean room at the Korean Pharmacopuncture Institute (KPI, K-GMP). The constituents of the Eun-Bi San pharmacopuncture are Angelicae gigantis radix, Strychni semen and Glycyrrhizae radix. These were extracted at low temperature and low pressure in an aseptic room at the KPI. Doses of Eun-Bi San pharmacopuncture, 0.25, 0.5 and 1.0 mL, were administered to the experimental groups, and a dose of normal saline solution, 1.0 mL, was administered to the control group. This study was performed under the approval of the Institutional Animal Ethics Committee of Biotoxtech Co., Ltd. Results: No deaths or abnormalities occurred in any of the four groups. No significant changes in weight, hematological parameters or clinical chemistry between the control group and the experimental groups were observed. To determine if abnormalities existed in any organs and tissues, we used microscopy to examine representative histological sections of each specified organ; the results showed no significant differences in any of the organs or tissues. Conclusion: The results of this study suggest that treatment with Eun-Bi San pharmacopuncture is relatively safe and that its clinical use may be beneficial. Further evaluations and studies on this subject will be needed to provide more concrete evidence in support of these conclusions.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.27 no.6
• /
• pp.373-381
• /
• 2015

As offshore structures such as offshore wind and offshore platforms have been installed frequently in ocean, scour effects are considered important. To test the scour effect, numerical simulation of scour has been carried out. However, the test was usually conducted under the uni-directional flow without bi-directional current flow in western sea of Korea. Thus, in this paper, numerical simulations of scour around offshore jacket substructure of HeMOSU-1 installed in western sea of Korea are conducted using FLOW-3D. The conditions are uni-directional and bi-directional flow considering tidal current. And these results are compared to measured data. The analysis results for 10,000 sec show that under uni-directional conditions, maximum scour depth was about 1.32 m and under bidirectional conditions, about 1.44 m maximum scour depth occurred around the structure. Meanwhile, about 1.5~2.0 m scour depths occurred in field observation and the result of field test is similar to result under bi-directional conditions.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.29-34
• /
• 2003

In this paper, we fabricated an 1.8 ㎓ differential VCO using a commercial 0.5 ${\mu}{\textrm}{m}$ SiGe BiCMOS process technology, The fabricated VCO consumes 16 ㎃ at 3 V supply voltage and has a 1.2 $\times$ 1.6 $mm^2$TEX>chip area. A phase noise measured at 100 KHz offset carrier is -110 ㏈c/Hz and a tuning range is 1795 MHz~1910 MHz when two varactor diodes are biased from 0 V to 3 V.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.131-137
• /
• 1996

Typical size distribution of emission particulates is bi-modal in shape with particles in the fine mode (< 2.0 $\mu\textrm{m}$) and the coarse mode. An experimental study of pressure drop across the industrial gas cleaning filters has been conducted using particle mixture of fine alumina and coarse Arizona dusts with a rotating aerosol disperser to generate the bi-modal test aerosol. Pressure drop increased linearly with increasing mass loading. The pressure drop was found to be strongly dependent upon the mass ratio of fine to coarse particles. The smaller the mass ratio of fine to coarse particles and the higher face velocity are, the faster pressure drop rises. The fine particles and the greater inertia of the particle moving fast would cause a denser cake formation on the filter surface, resulting in a greater specific resistance to the gas flow.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.14 no.4
• /
• pp.1460-1478
• /
• 2020

This paper proposes a novel anti-collision protocol for large-scale RFID tags identification, named Bi-response Collision Tree Protocol (BCT). In BCT, two group of tags answer the reader's same query in two response-cycles respectively and independently according to the bi-response pattern. BCT improves the RFID tag identification performance significantly by decreasing the query cycles and the bits transmitted by the reader and tags during the identification. Computation and simulation results indicate that BCT improves the RFID tag identification performance effectively, e.g. the tag identification speed is improved more than 13.0%, 16.9%, and 22.9% compared to that of Collision Tree Protocol (CT), M-ary Collision Tree Protocol (MCT), and Dual Prefix Probe Scheme (DPPS) respectively when tags IDs are distributed uniformly.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.149-152
• /
• 2001

A Single-phase bi-directional inverter Using a diode bridge-type resonant circuit to implement ZVT(Zero Voltage Transition) switching is Presented. It is shown that the ZACE(Zero Average Current Error) algorithm based polarized ramptime current control can provide a suitable interface between diode bridge-type resonant circuit DC link and the inverter. The current control algorithm is analyzed about how to design the circuit with analyzed switch which m ZVT operation for the main power switch The simulation and experimental results would be shown to verify the proposed current algorithm, because the main power switch is turn on with ZVT and the bi-directional inverter is operated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.62-65
• /
• 2001

$SrBi_2Ta_2O_{9}$ thin films were etched in inductively coupled $Cl_{2}$/$CF_{4}$/Ar plasma. The maximum etch rate was 1060 $\AA\textrm{m}$/min in $Cl_{2}$/$CF_{4}$/Ar (80). The chemical reactions on the etched surface were studied with x-ray photoelectron spectroscopy. The etching of SBT thin films in $Cl_{2}$/$CF_{4}$/Ar were etched by chemically assisted reactive ion etching. The small addition of $Cl_2$ into $CF_4$(20)/Ar(80) plasma will decrease the fluorine radicals and the increase Cl radical.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2001.02a
• /
• pp.25-28
• /
• 2001

Bi-2212 HTS tube was fabricated by centrifugal forming process(CFP). As a variation of melt casting process(MCP) or centrifugal casting technique, the centrifugal forming process is a flexible method for manufacturing Bi-2212 bulk tubes and has been optimized to achieve smooth surface and uniform thickness. At this process, the slurry was prepared in the mixing ratio of 10:1 between Bi-2212 powder and binder and initially charged into the rotating mold under the speed of 300~450 rpm Heat-treatment was performed at the temperature ranges of 860 ~ $890^{\circ}C$ in air for partial melting. The HTS tube fabricated by centrifugal forming process at $890^{\circ}C$ under the rotating speed of 450 rpm was highly densified and the plate-like grains with more than 20$\mu$m were well oriented along the rotating axis. The measured Tc and Jc at 10K were around 85K and 3,000A/cm2 respectively.