• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.244-244
• /
• 2012

Polymer memory devices have attracted considerable attention because of their advantages such as low cost potential, good scalability, flexibility, simplicity in structure, and large capacity for data storage. Metal/poly (4,4'-aminotriphenylene hexafluoroisopropylidenediphthalimide) (6F-TPA PI)/metal system has been found to show an electrical bi-stable behavior. Here, we show a novel set-up of 6F-TPA PI/Al sample in which holes are injected by photoelectron emission process instead of direct charge carrier injection via metal electrode. In this process, an irreversible electrical phase transition of 6F-TPA PI is found, leading to a write-once-read-many (WORM) behavior. The photoelectron spectroscopy results measured before and after the switching process revealed that the irreversible electrical phase transition of 6F-TPA PI is attributed to the chemical modification of the carbonyl group in phthalimide moiety.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.297-298
• /
• 2011

Metal/poly (4,4'-aminotriphen-ylene hexafluoroisopropylidenediphthalimide) (TP6F PI)/metal structure exhibited an electrically volatile phase transition with high (OFF) or low (ON) resistive states when voltage between electrodes swept. Here, we demonstrate a noble set-up in which holes are injected by photoelectron emission process during the voltage sweep instead of direct charge carrier injection via metal electrode, which enables direct investigation into changed electronic structures of TP6F PI both in ON and OFF states using photoemission spectroscopy methods. In the I-V measurement, TP6F PI shows a non-volatile behavior. In spectroscopic results, this non-volatile behavior is leaded from the structural modification of the O=C double bond in phthalimide of TP6F PI by hole injection.

• Proceedings of the Botanical Society of Korea Conference
• /
• 1985.08b
• /
• pp.23-33
• /
• 1985

Plant cell culture is emerging to express bioactive foreign proteins because it has several advantages in that it is safe, economical, genetically stable and eukaryotic expression system comparing with other expression systems. However several limitations such as slow growth rate, low expression level and lack of well established down stream process need to be answered. As a preliminary approach to produce the immunologically interested molecules through the plant cell culture, we tested if granulocyte-macrophage colony stimulating factors (GM-CSFs) from both murine (mGM-CSF) and human (hGM-CSF) are produced as a biologically active form through plant cell culture. The murine and human GM-CSF genes were cloned into the plant expression vector, pBI121, and Ti-plasmid mediated transformation of tobacco leaves was conducted using Agrobacterium tumefaciens harboring both recombinant GM-CSF (rGM-CSF) genes. Cell suspension culture was established from the leaf-derived calli of transgenic tobacco plant. Northern blot analysis indicated the expression of the introduced mGM-CSF gene in both transgenic plant and cell suspension cultures. In addition, the biological activities of both murine and human GM-CSF from plant cell culture were confirmed by measuring the proliferation of the GM-CSF dependent FDC-PI and TF-1 cells, respectively.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.434-437
• /
• 2009

To realize the advantages of e-Paper, driving systems should be separated from panels to keep its superiority in thin, light, and flexible. For this purpose, this paper develops a panel hot-plugging driving system for R2R cholesteric LCD. Its performance is verified by implementing an e-Badge application. Satisfactory results are obtained.

• Journal of electromagnetic engineering and science
• /
• v.8 no.1
• /
• pp.28-33
• /
• 2008

We have proposed a novel DVB-H(Digital Video Broadcast for Handheld) antenna for folder-type mobile handheld terminal by using a coupling element, a stub, and an L-type matching circuit. The L-type matching circuit consisting of two chip inductors is used for achieving an improved impedance matching over the DVB-H frequency band ($470{\sim}702\;MHz$). Simulated results showed the stub worked to more knot the lower and upper frequency ends of the input impedance curve. The antenna exhibits a flat gain characteristic from 2 to 2.8 dBi over the DVB-H frequency band. The radiation patterns are a stable Figure-of-eight radiation pattern in the frequency range.

• Journal of Power Electronics
• /
• v.7 no.3
• /
• pp.203-212
• /
• 2007

In this paper, a proposed approach to improve the power factor of three-phase rectifiers and to stabilize the output voltage against load change is presented. The elements of the given control strategy are small size, low cost, high performance, and simplicity. The proposed control strategy of switches is based on a prototype of three bi-directional switched consisting of four diodes and one IGBT. A control technique and operational procedure are also developed, both theoretically and experimentally. The experimental results clearly verify the theoretical analysis from the prototype connected to grid unity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.926-929
• /
• 2012

The $Sr_{0.7}Bi-{2.3}Nb_2O_9$(SBNO) thin films were deposited on Si substrate by RF magnetron sputtering method at $300^{\circ}C$ of substrate temperature. And the SBNO thin films were annealed at $650{\sim}800^{\circ}C$ using RTA (rapid thermal annealing). The grain of SBNO thin films were increased with the increase of annealing temperature. The dielectric constant (100) of SBNO thin film was obtained by RTA above $750^{\circ}C$. The voltage dependence of dielectric loss showed a value within 0.03 in voltage ranges of -5~+5 V. Also, the dielectric constant characteristics showed a stable value with the increase of frequency.

• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.1071-1087
• /
• 2017

This paper introduces a DC/AC converter, which can be connected in parallel with a diode rectifier for regenerative applications. The DC/AC converter is supposed to transmit regenerative energy to the power grid when a motor is braking. Isolation transformers are not needed in the topology, which can reduce the size and cost. An analysis of the zero-order current existing in the system is carried out. In addition, algorithms to minimize the zero-order current, control the power factor and keep the DC bus voltage stable are discussed. A 55kW industrial prototype is built to verify the proposed analysis and control strategies.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2245-2251
• /
• 2013

In this paper, a design of a compact series-fed dipole pair(SDP) antenna with end-loaded rectangular patches is presented. In order to reduce the lateral size of a conventional SDP antenna, rectangular patches are end-loaded to the two dipole elements of the SDP antenna and a grooved ground plane is used by adding a patch at both ends of the ground plane. The effects of varying the length and width of the rectangular patches on the antenna performance such as input reflection coefficient are investigated. An optimized compact SDP antenna covering a frequency band ranging from 1.7 GHz to 2.7 GHz is designed and fabricated on an FR4 substrate. The total width of the fabricated prototype of the proposed antenna is reduced by approximately 14.3% compared to the conventional SDP antenna. Experimental results show that the antenna presents a 48.7% bandwidth in the range of 1.68-2.76 GHz and a stable gain of 5.6-6.0 dBi with minimal degradation. Moreover, a front-to-back ratio is improved by about 0.7 to 7.4 dB.

• Journal of IKEEE
• /
• v.16 no.1
• /
• pp.62-68
• /
• 2012

The planar microstrip antenna for the safety communication of life at sea is designed and manufactured to effectively receive the emergency wireless signal from the transmitter on the life vest. The proposed microstrip antenna in this paper is easy to make, light weight and cheap compared to other antennas because of printed antenna fabrication. To overcome the narrow bandwidth, large size and low gain characteristics of microstrip antenna, we use the IDMA(Identical Dual Patch Microstrip Antenna with Air-Gap) structure. The proposed antenna was fabricated with the use of 1.6mm FR4 and measured with the 28.7MHz(6.6%) of bandwidth and 3.04dBi of gain at the frequency of 426MHz. To validate the proposed antenna, we experimented the possible distance range at sea using the commercial UHF transceiver module and obtained over 5km distance for stable communication. This antenna can be widely applied to application of the UHF wireless mobile communication.