• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.81-88
• /
• 2005

In soft grounds with deep bearing stratum, the PHC piles are generally joined by welding or prefabricated method. However, the existing joining methods have some problems in a side view of workability, quality and cost etc. In this study, a new joining method of PHC piles, which removes the problems of the existing methods, is developed. Static and dynamic load tests in fields as well as laboratory tests such as tensile and bending tests are conducted to investigate the workability and structural safety of PHC piles joined by the new method. The test results show that tensile and bending resistances of the joint part are higher than those of PHC pile itself. PHC piles with 400mm diameter are joined by the new method within 4 minutes while 25 minutes for welding method. Bearing capacities of the PHC piles joined by the new method are nearly the same as those of jointed PHC piles by welding method.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.2
• /
• pp.357-364
• /
• 2002

The study performed a series of flexural tests on Closed Cold-Formed Steel Sections for stud, joist, and roof truss. Results were compared with analytical values. Each 2.4-m long and 0.9-m wide specimen consisted of two steel beams set at 0.46 m interval. The steel beams were attached to the specimens using either plaster board or ply wood. Another specimens did not use any attachment material. Positive and negative bending tests were conducted to investigate the composite behavior, including the effects of plaster board or ply wood on the buckling behavior of steel beam. Full-scale roof truss tests were also performed to study the buckling behavior and failure mode of the truss members.

• Nuclear Engineering and Technology
• /
• v.53 no.5
• /
• pp.1580-1586
• /
• 2021

The application of induction bending processes to industrial pipe production is increasing. The induction bending process has the effect of reducing the number of inspections and preventing leaks by reducing the weld of the pipe. For these reasons, efforts have been made to apply an induction bending process to the pipe of the PGSFR under development in Korea and this is the first attempt in the SFR design. Since the PGSFR pipe has a relatively large diameter-to-thickness ratio, it is difficult to fabricate an induction bending pipe that meets the requirements. In addition, the material properties may change because the pipe heats to a very high temperature during the induction bending process. In this study, P91 pipes were fabricated by induction bending, and the results from analyzing the induction bending process' applicability to the P91 pipe of the PGSFR are examined. The various dimensional measurements of the pipes fabricated by the induction bending process were surveyed to determine whether the requirements of the ASME Code were met. The minimum thickness, ovality, and wall buckling measured in the fabricated pipe met all the requirements. Tensile, impact, and hardness tests at various locations of the fabricated pipe also satisfied the requirements.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.152-155
• /
• 2003

In order to examine the springback of aluminum alloy sheets, AL1050 and AL5052, in the warm forming which forms the sheet above room temperature, the stretch bending and draw bending tests in various working temperatures were carried out. While the springbacks of AL5052 and AL1050 are tremendously reduced over 150$^{\circ}C$ in the stretch bending test, the springbacks in the draw bending test are rapidly reduced in 150$^{\circ}C$-200$^{\circ}C$ for AL5052 and 200$^{\circ}C$-250$^{\circ}C$ for AL1050. Using the FEM program, the forming and springback processes are analyzed. Though springback amounts of analysis result are slightly bigger than those of experiment, they showed the same trend in the decreasing springback as the forming temperature increases.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.76-79
• /
• 2005

Bending deformation and energy absorption characteristics of aluminum-composite hybrid tube beams have been analyzed for improvement in the bending performance of aluminum space frame by using experimental tests combined with theoretical and finite element analyses. Hybrid tube beams composed of glass fabric/epoxy layer wrapped around on aluminum tube were made in autoclave with the recommended curing cycle. Basic properties of aluminum material used for initial input data of the finite element simulation and theoretical analysis were obtained from the true stress-true strain curve of specimen which had bean extracted from the Al tube beam. A modified theoretical model was developed to predict the resistance to the collapse of hybrid tube beams subjected to a bending load. Theoretical moment-rotation angle curves of hybrid tube beams were in good agreement with experimental ones, which was comparable to the results obtained from finite element simulation. Hybrid tube beams strengthened by composite layer on the whole web and flange showed an excellent bending strength and energy absorption capability.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.276-279
• /
• 2004

Concrete is one of the principal materials for the structure and it is widely used all over the world. but it shows extremely brittle failure under bending and tensile load. Recently to improve such a poor property. High Performance Fiber Reinforced Cementitious Composites (HPFRCC) have been developed. and it are defined by an ultimate strength higher than their first cracking strength and the formation of multiple cracking during the inelastic deformation process. This study is to develop the hybrid HPFRCC with high ductility and strain capacity in bending and tensile load. and the three-point bending test on hybrid HPRFCC reinforced with micro and macro fibers is carried out in this paper. As the results of the bending tests. hybrid HPFRCCs reinforced with PVA40+SF and PVA100+PVA660 showed the high ultimate bending stress, multiple cracks and displacement hardening under bending load.

• Journal of Biosystems Engineering
• /
• v.18 no.1
• /
• pp.30-36
• /
• 1993

Cucumbers being living biological materials are generally vulnerable to external forces, especially, bending force during the processes, because they have usually longish shape. Understanding the mechanical and viscoelastic properties of cucumber is important to analyze various characteristics which might be helpful in determining design parameters for the processing equipment such as sorting, packaging and transporting machine. The objectives of this study were to determine ultimate bending strength, deflections, and hysteresis losses for the cucumbers from the bending tests. Within the range of loading rate from 20 to 100mm/min, the ultimate bending strength of the cucumber samples were 525-630kPa at the Gyeousalicheongjang and the Baekdadagi, and 476~618kPa at the Cheongjangmadi, respectively, but the ultimate bending deflection ratio of the Cheongjangmadi showed the highest value among the tested samples. The effect of loading rate on the physical properties of the cucumber was relatively significant, all considered physical properties and degree of elasticity of the cucumber increased with the loading rate, but the hysteresis loss decreased with it.

• Journal of Aerospace System Engineering
• /
• v.4 no.1
• /
• pp.23-26
• /
• 2010

In this study, it was performed damage assesment of small scale composite aircraft developing. This aircraft adopted the sandwich structure to skin of wing. This study aims to investigate the residual strength of sandwich composites with Nomex honeycomb core and carbon fiber face sheets after the open hole damage by the experimental investigation. The 4-point bending tests were used to find the bending strength, and the open hole was applied to introduce the simulated damage on the specimen. The bending strength test results after open hole was compared with the results of no damaged specimen test. The FEM analysis is assessed via an experimental 4-point bending test.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.61-67
• /
• 2000

Gears are the most commonly used parts in automotive and industrial applications. One of most common modes of gear failures is tooth breakage, which is usually produced by the bending fatigue failure. It is important to manufacture the gears which can withstand the applied stresses in view of safety and economic requirement. This paper deals with bending fatigue strength for cold forged bevel gear. Especially, to compare fatigue characteristics for manufacturing processes difference, bending fatigue tests of bevel gears made by three different processes respectively. Results indicate that the fatigue strength of bevel gear is improved by cold forging process. Intergranular fracture is found on fatigue fracture surface, and dimples are observed on final fracture surface. The fatigue failure cannot be considered as a deterministic quantity, but must be characterized statistically. This study proposes a method to estimate bending fatigue lift of the bevel gear using the probability-load-life and Weibull analysis.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.325-326
• /
• 2023

This paper presents an experimental study on the bending behavior of Kagome truss composite beams reinforced by fiber-reinforced composites (FRC). Two types of FRCs, i.e., high ductile FRC with a high tensile ductility and high strength FRC with high compressive strength were used; and three Kagome truss composite beams reinforced by FRCs were manufactured. In order to investigate the bending behavior of beams, bending tests were carried out. Test results showed that types of FRCs and reinforcement methods significantly influenced the bending behavior of Kagome truss composite beams.