• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.130-143
• /
• 1997

A heat-pressed technique(IPS-Empress, Ivoclar) has been described to construct single unit crown, inlay/onlay and veneers using a partially pre-cerammed and pre-colored glass-leucite ingot that has the greateast strength by the combination of heat-pressed procedure through the smalldiameter sprue and heat treatment procedure. The purpose of this study was to evaluate the flexure strength of a heat-pressed ceramic material(IPS-Empress) without simulated firing treatments according to pontic designs. Two groups of 9 disks(1.4mm thick, 14mm in diameter) each using two types of sprues with different diameters($({\Phi}2.8\;,{\Phi}1.8)$) and numbers were prepared. The specimens were mounted in the testing jig. The flexural strengths were determined, by means of the bi-axial bending test, by loading the center of disk to failure using a universal testing machine(Zwick 145141, Zwick, Germany) at a cross-head speed of 1.0 mm/min. The means flexural strength value of one group using a sprue with ${\Phi}2.8$ was $140.4{\pm}8.0Mpa$. That of the other group using two sprues with ${\Phi}1.8$ was $151.8{\pm}10.3Mpa$. After analysis, results showed that there was a statistical difference between groups(t=2.33m p<0.05). No clnical implications were drawn from these data because of absence of simulated firing treatment.

• 대한치과보철학회지
• /
• 제35권1호
• /
• pp.144-164
• /
• 1997

The purpose of this study were to investigate the chemical composition, mean particle size, linear thermal expansion coefficient and metal-bonding strength of the regular opaque powder and core powder. In this study, 4 types of ceramic powders, namely Duceram Jacket Opaque powder, Duceram Opaque powder, Vita Hi-Ceram powder, Vita VMK Paint On-88 powder were used. Chemical composition was evaluated by EDS(Energy Dispersive X-ray Spectrophotometer, Oxford QX-2000, England), particle size was measured by MALVERN Instruments(MALVERN Instruments SB. OC., U.S.A.. ad linear thermal expansion coefficient was measured by dilatometer(Motoyama, Japan). Bond strength was measured by the Universal tsting machine(Istron Co., Ltd., U.S.A.). The Results were as follows : 1. Through recognition of the relative difference in chemical composition between the core powder and the regular opaque powder, the difference in the proportion of $Al_2O_3$ in each type of material is demonstrated ; Duceram Jaket Opaque powder : 30.16%, Duceram Opaque powder : 16.60%, Vita Hi-Ceram : 63.64%, Vita VMK Paint-On 88 : 16.16%. 2. There was no significant difference in the proportion of metal-bonding materials between the core powder and the regular opaque powder. 3. In the regular opaque powder, alkaline materials were incoporated in order to increase the coefficient of thermal expansion. 4. In the particle size analysis, there was no significant difference in mean particle size or in the particle size distribution between the core powder and the regular opaque powder. 5. In the thermal expansion test for temperature range of $25-600^{\circ}C$, the regular opaque powder had higher coefficient of thermal expansion than that of core powder. 6. In the 4 point flexural bending test, there was no statistically significant difference in the mean bond strength between the core powder and the opaque powder among the Duceram products.

• 한국항해항만학회지
• /
• 제29권10호
• /
• pp.871-876
• /
• 2005

기존의 기계적인 센서들보다 높은 민감도와 선형성을 가지는 반도체 압력 센서들은 크기가 작고 일괄공정에 의해 제작될 수 있는 반도체 공정 기술로 제작되므로 다양한 산업에서 적용되고 있다. 하지만 열과 반복적인 외부 하중은 센서의 수명에 치명적인 영향을 미치고 있고, 특히 외부에서 가해지는 열은 센서를 구성하는 구조물보다 신호를 전달하는 금속 배선의 피로 수명에 지대한 영향을 미치고 있으므로 이에 대한 영향성을 분석할 수 있는 프로세스를 확립하고, 이후 다양한 재료의 반복적인 열하중에 대한 피로 수명을 Manson & Coffin식에 따라서 평가하였다. 금속 배선의 밑단에서 피로수명이 가장 낮고, 굽힘하중은 피로 수명보다는 응력분포에 큰 영향을 미치고 있다.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• 대한치과보철학회지
• /
• 제32권2호
• /
• pp.249-267
• /
• 1994

The purpose of this study was to compare the fatigue, physical properties, flexibility and surface roughness of titanium used in removable partial dentures with those of a type IV and alloy and a cobalt- chromium alloy. Fatigue testing subjected the test specimen to rapid cycling at a given stress until failure occurred by using a small-sized, electrodynamic type bending fatigue testing machine. The S-N curves for the framework materials were generated. For tensile testing, a tensile bar as described in the ADA Specification No.14 was subjected to tensile loading until failure occurred. Load-displacement curves were generated for 18 gauge round specimen and tapered half round specimen. Then the flexibilities were calculated. The surface roughnesses were compared by analyzer. Through analyses of the data, the following conclusions were obtained. 1. The fatigue property of titanium was higher than that of a type IV gold alloy$(p\leq0.05)$, but there was no significant difference between titanium and a cobalt-chromium alloy $(p\geq0.05)$. 2. The yield strength, the ultimate tensile strength and Victors hardness of titanium were higher than those of a type IV gold alloy but lower than those of a coalt-chromium alloy$(p\leq0.05)$. 3. The percentage of elongation and reduction of area of titanium were the highest $(p\leq0.05)$. 4. The surface roughness of titanium was the greatest$(p\leq0.05)$. 5. The flexibility of titanium was lower than that of a type IV gold alloy but higher than that of a cobalt-chromium alloy$(p\leq0.05)$.

• 한국전산구조공학회논문집
• /
• 제26권3호
• /
• pp.199-205
• /
• 2013

본 논문에서는 와이어 하네스의 피로 내구 수명을 예측하기 위해 와이어, 번들, 실차단계의 유한요소 해석 방법론이 연구되었고 이를 위한 피로 내구 시험 기기가 개발되었다. 와이어 하네스 시스템을 구성하는 5가지 종류의 와이어에 대한 응력-수명 그래프를 얻기 위해 개발된 피로 시험기를 이용하여 반복 굽힘 움직임을 인가하였다. 와이어를 구성하는 도선과 피복의 재료 모델링을 위해 혼합의 법칙이 적용된 등가모델을 이용하였다. 번들 해석과 시험을 통하여 와이어 간의 접촉조건과 번들의 테이핑조건이 정립되었다. 와이어 및 번들 단계의 결과들은 실차 단계의 해석에 적용되었다. 실차단계의 해석을 위해 번들과 그로맷으로 구성된 와이어 하네스 시스템을 수치적으로 모델링 하였으며, 차량 문의 개폐조건이 와이어 간의 접촉조건과 함께 적용되었다. 유한요소 해석을 이용한 실차 모델의 피로 내구 해석을 통해 70만회 이상의 피로 수명이 도출 되었으며, 실차 조건의 시험 결과와비교하여 타당성을 검증하였다.

• 대한치과교정학회지
• /
• 제48권2호
• /
• pp.107-112
• /
• 2018

Objective: The aim of this study was to examine the properties of fiber-reinforced composite and stainless steel twisted retainers for orthodontic retention. Methods: Three different span lengths (5.0, 8.0, and 14.0 mm) of fiber-reinforced composite were investigated. The three fiber-reinforced composite retainer groups were subdivided according to the storage condition (dry and wet), resulting in a total of six groups. Each stainless steel and fiber-reinforced composite group was comprised of six specimens. The three-point bending flexural test was conducted using a universal testing machine. ANOVA was used to assess differences in the maximum load and maximum stress according to the span length, material, and storage condition. Post-hoc comparisons were performed if necessary. Results: The maximum stress and maximum load were significantly (p < 0.001) associated with the span length, material, and storage condition. The significant interaction between the material and span length (p < 0.001) indicated the differential effects of the material for each span length on the maximum stress and maximum load, with the difference between materials being the highest for the maximum span length. Conclusions: Our findings suggest that fiber-reinforced composite retainers may be an effective alternative for orthodontic retention in patients with esthetic concerns or allergy to conventional stainless steel wires.

• 대한치과기공학회지
• /
• 제31권4호
• /
• pp.37-43
• /
• 2009

This study evaluated the effect of concentration of glass fiber reinforcement on the flexural properties of auto and heat polymerized denture base resin. The test specimens($64{\times}10{\times}3.3mm$) were made of auto and heat polymerized resin(Vertex, Dentimax, Netherlands). Glass fiber(ER 270FW, Hankuk Fiber Glass, Korea) were used to reinforce the denture base resin. The 2.6%, 5.3% and 7.9% volume pre-impregnated fiber were located at the bottom of specimen. The test specimens(n=7) of each group were stored in distilled water at $37^{\circ}C$ for 50 hours before test. The flexural strength and modulus were measured by an universal testing machine(Z020, Zwick, Germany) at a crosshead speed of 5 mm/min in a three-point bending mode. The data was analyzed by one-way ANOVA and the Duncan's multiple range test(${\alpha}$=0.05). The difference of auto polymerized resin groups and heat polymerized resin groups were statistically analyzed by t-test(${\alpha}$=0.05). Glass fiber showed significant reinforcing effects on auto and heat polymerized resin. For flexural strength and modulus, auto polymerized resin was the highest in 7.9% volume, while heat polymerized resin was the highest in 5.3% volume. In this study, glass fiber at 7.9% volume ratio showed most effective reinforcing effect on auto polymerized resin and glass fiber at 5.3% volume ratio showed most effective reinforcing effect on heat polymerized resin in terms of flexural strength and flexural modulus.

• 대한기계학회논문집
• /
• 제17권2호
• /
• pp.237-247
• /
• 1993

본 연구에서는 CFRP 적층재를 구조재료로 사용할 경우 우수한 인장강도를 갖 지만, 충격하중에 취약한 특성을 갖기 때문에 구조안정성에 관한 큰 문제의 하나로 충 격손상을 받은 적층판의 잔류 압축강도가 현저히 저하되는 것이 문제점으로 지적되어 왔다.특히, 충격손상에 의한 압축강도의 저하는 인장강도보다 압축강도에 중점을 두는 항공기의 강도설계에서 중요한 문제가 되므로, 저속충격에 의한 복합재료 구조체 의 충격파괴의 문제를 잘 이해하는 것이 요구된다. 지금까지의 연구에 의하면 CFRP 복합적층재의 손상은 주로 층간박리현상과 손상역의 크기변화를 실험적으로 고찰하였 다.

• 대한구순구개열학회지
• /
• 제7권2호
• /
• pp.93-106
• /
• 2004

본 연구의 목적은 편측성 구순구개열 (UCLP) 환자에서 술전 비치조 정형장치 (presurgical nasoalveolar molding appliance, PNAM) 와 구순 봉합수술의 치조골 정형효과를 3차원 (3-D) 분석을 통하여 평가하는 것이다. 연구대상은 16명의 UCLP 환자 (평균 파열부거리: 10.46mm) 이며 PNAM 장치에 의한 치료와 rotation-advancement법에 의한 구순 봉합수술을 받았다 처음 내원시 (평균연령: $37.0{\pm}27.89$ 일), PNAM 치료를 받고 난 후이며 구순봉합수술 1달 전 (평균연령: $119.25{\pm}40.18$ 일), 구순봉합수술 2달 후 (평균연령: $190.81{\pm}42.78$ 일)에 상악의 인상을 채득하였다. 그 후 laser scanning machine (Orapix, Dimennex, Seoul, Korea) 과 3-D view software (3Dxer, Dimennex) 를 사용하여 3-D모형을 제작하였다. 선, 각도, 정중선변이, 거리, 면적 항목을 3-D 모형상에서 계측하고, 각 시기별의 차이를 비교하기 위하여 Wilcoxon signed rank test를 사용하여 분석하였다. PNAM치료 동안과 구순 봉합수술 후에도 치조골 후방부는 안정된 구조물이었다. PNAM치료에 의한 파열부 거리의 감소는 대분절 (greater segment) 의 내측 굴곡 (bending) 에 의하여 발생하였다. 대분절 (greater segment)의 전방 성장은 PNAM치료에 의하여 억제되었으나, 구순 봉합수술 후에 회복되었다. 구순 봉합수술 후에 대분절과 소분절 사이의 전방부 각도의 증가는 구순 반흔 (lip scar) 의 압력에 의한 치조골 정형 효과 때문으로 생각된다. 정중선변이는 PNAM치료에 의하여 개선되었다. PNAM치료 동안과 구순 봉합수술 후에 구개부 (palatal segment) 의 면적은 계속 증가하였다. 치조골 면적과 거리 항목의 증가는 후방부에서 크게 나타났다. 이러한 결과는 PNAM치료에 의한 치조골 정형효과는 주로 전방부에서 발생하며, 치조골의 성장은 구순 봉합수술 후에 후방부에서 주로 발생한다는 것을 의미한다.