• 한국산학기술학회논문지
• /
• 제12권3호
• /
• pp.1078-1084
• /
• 2011

스포츠화의 설계에서 신발 앞축 부분의 굽힘강성은 매우 중요한 설계인자이지만, 측정하기가 어렵다. 본 논문은 이러한 굽힘강성을 측정하는 장비를 소개한다. 장비는 알루미늄 프레임 구조와 AC 모터, 2개의 로드셀, 엔코더와 제어용 하드웨어로 구성되어있으며, 신발의 굽힘 모멘트를 측정하는 메카니즘을 소개하였다. 유용성을 입증하기 위하여, 신발의 소재와 디자인이 굽힘강성에 미치는 영향을 관찰하는데 사용되어 졌다. 실험을 위하여 신발 중창소재의 경도와 두께를 달리하여 완성신발 시편을 제작하였다. 이들 시편으로 굽힘실험을 수행하고, 최소자승법을 사용하여 굽힘강성을 구하였다. 실험결과 PU 중창으로 만든 신발이 PH 중창으로 만든 신발보다 굽힘강성이 높았으며, 중창의 두께가 중창의 경도보다 굽힘강성에 미치는 영향이 크다는 것을 알아낼 수 있었다. 따라서, 이러한 실험결과를 바탕으로, 본 측정장비는 유용한 실험결과를 도출할 수 있었으며, 이 장비를 통하여 측정된 신발의 굽힘강성은 신발 설계의 유용한 설계인자로 활용될 수 있다고 사료된다.

• Journal of Mechanical Science and Technology
• /
• 제20권2호
• /
• pp.234-241
• /
• 2006

A functional external fixator system for bone deformity near the joints using worm gear was developed for curing the angle difference in fracture bones while the lengthening bar was developed for curing the differences in length, also in fracture bones. Both experiments and FE analysis were performed to compare the elastic stiffness in several loading modes and to improve the functional external fixator system for bone deformity near joints. The FE model using compressive and bending FE analysis was applied due to the angle differentiations. The results indicate that compressive stiffness value in the experiment was 175.43N/mm, bending stiffness value in the experiment was 259.74 N/mm, compressive stiffness value in the FEA was 188.67 N/mm, and bending stiffness value in the FEA was 285.71 N/mm. Errors between experiments and FEA were less than $10\%$ in both the 'compressive stiffness and the bending stiffness. The maximum stress (157 MPa) applied to the angle of the clamp was lower than the yield stress (176.4 MPa) of SUS316L. The degree of stiffness in both axial compression and bending of the new fixator are about 2 times greater than other products, with the exception of EBI (2003).

• 한국항공우주학회지
• /
• 제42권5호
• /
• pp.390-397
• /
• 2014

BO-105 헬리콥터는 무힌지 로터 허브시스템이 적용되었으며, 블레이드의 루트 영역이 무힌지 허브 시스템의 플렉셔에 해당한다. 따라서 본 블레이드를 이용한 훨타워 시험 수행을 대비하여 굽힘 강성이 낮은 플렉셔 부분에 대한 굽힘 강성 보강을 수행하였다. 플렉셔 굽힘 강성 보강 수행을 위해 플렉셔 부분의 단면 형상을 모델링하여 굽힘 강성을 계산하였으며, 이를 바탕으로 강성 보강을 위한 복합재의 두께를 선정하였다. 보강된 플렉셔의 실제 굽힘 강성을 확인하기 위하여 강성보강 전 형상에 대한 강성 측정 시험과 강성보강 이후 형상에 대한 강성 측정 시험을 수행하여 결과를 비교하였다.

• Steel and Composite Structures
• /
• 제38권6호
• /
• pp.637-656
• /
• 2021

The component-based method is widely used to analyze the initial stiffness of joint in steel structures. In this study, an analytical component model for determining the column face stiffness of square or rectangular hollow section (SHS/RHS) subjected to tension was established, focusing on endplate connections. Equations for calculating the stiffness of the SHS/RHS column face in bending were derived through regression analysis using numerical results obtained from a finite element model database. Because the presence of bolt holes decreased the bending stiffness of the column face, this effect was calculated using a novel plate-spring-based model through numerical analysis. The developed component model was first applied to predict the bending stiffness of the SHS column face determined through tests. Furthermore, this model was incorporated into the component-based method with other effective components, e.g., bolts under tension, to determine the tensile stiffness of the T-stub connections, which connects the SHS column, and the initial rotational stiffness of the joints. A comparison between the model predictions, test data, and numerical results confirms that the proposed model shows satisfactory accuracy in evaluating the bending stiffness of SHS column faces.

• Geomechanics and Engineering
• /
• 제34권6호
• /
• pp.611-621
• /
• 2023

This paper presents the results of a numerical investigation of the effect of geotextile reinforcement on underlying buried pipe behavior using PLAXIS 3D. In this study, variable parameters such as the in-plane stiffness of the geotextile, the pipe stiffness, the soil stiffness, the footing width, the geotextile width, and the location of the geotextile reinforcement layer are investigated. Deflections and bending moments acting on the pipe are evaluated for different combinations of variables and are presented graphically. It is observed that with an increase in the in-plane stiffness of the geotextile reinforcement, there is a tendency for a decrease in both deflections in the pipe and bending moments acting on the pipe. Conversely, with an increase in the pipe stiffness, geotextile reinforcement efficiency decreases. In the investigated region of soil stiffness, for the given pipe and geotextile stiffness, an optimum efficiency of geotextile is observed in medium dense soils. Further, it is shown that relative lengths of geotextile and footing has an important role on geotextile efficiency. Lastly, it is also demonstrated that relative location of geotextile layer with respect to the buried pipe plays an important role on the geotextile efficiency in reducing the bending moments acting on the pipe and deflections in the pipe. In general, geotextiles are more efficient in reducing the bending moments as opposed to reducing deflections of the pipe. Numerical validation is done with an experimental study from the literature to observe the applicability of the numerical model used.

• 한국정밀공학회지
• /
• 제22권3호
• /
• pp.162-169
• /
• 2005

The functional external fixator system fur bone deformity near joints in legs using the worm gear was developed for curing the difference angles in fracture bone and the lengthening bar for curing the difference length in fracture bone. Both experiments and FE analysis were performed to compare the elastic stiffness in several loading modes and to improve the functional external fixator system for the bone deformity. The FE model using the compressive and bending FE analysis was applied to the FE analysis due to the angle differences. The results show that the compressive stiffness value in experiment was 175.43N/mm; the bending stiffness value in experiment was 259.74N/mm; compressive stiffness value in FEM was 188.67N/mm; bending stiffness value in FEA was 285.71N/mm. The errors between experiments and FEA were less than 10%. The maximum stress (157MPa) to the angle of clamp was lower than the yield stress (176.4MPa) of SUS316L. The stiffnesses in both axial compressive and bending of the new fixator are about 2 times higher than other products except EBI (2003).

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1248-1251
• /
• 2004

The functional external fixator system for bone deformity near joints in legs using the worm gear was developed for curing the difference angles in fracture bone and the lengthening bar for curing the difference length in fracture bone. Both experiments and FE analysis were performed to compare the elastic stiffness in several loading modes and to improve the functional external fixator system for bone deformity near joints in legs. The FE model using the compressive and bending FE analysis was applied the FE analysis due to the angle differences. The results show that the compressive stiffness value in experiment was 175.43N/mm, the bending stiffness value in experiment was 259.74N/mm, compressive stiffness value in FEM was 188.67N/mm, bending stiffness value in FEA was 285.71N/mm. The errors between experiments and FEA were less than 10％. The maximum stress (157MPa) to the angle of clamp was lower than the yield stress (176.4MPa) of SUS316L. The stiffnesses in both axial compressive and bending of the new fixator are about 2 times higher than other products except EBI (2003).

• 한국산학기술학회논문지
• /
• 제18권11호
• /
• pp.762-769
• /
• 2017

준등방성 라미네이트내의 확장강성 계수는 방사방향으로균일하지만, 굽힘강성 계수는 플라이 적층순서에 의해 방사방향으로 변화한다. 이 논문에서는 복합재 광학에서 사용되는 단방향섬유 복합재료와 무작위로 분포된 단섬유 복합재료로 이루어진 세 가지 유형의 준 등방성 라미네이트 반사경내의 굽힘강성 계수의 방사방향의 변화량을 비교하였다. 단섬유 복합재료 반사경 방사방향의 확장강성 계수와 굽힘강성 계수는 균일하게 나타나는 반면, 단방향섬유 복합재료 반사경의 경우에는 굽힘강성 계수의 방사방향으로의변화량이 11%에서 많게는 26%까지 변화하는 것으로 나타났다. 또한 강성계수의 차이로 인한 굽힘-비틀림-커플링 효과 등 강성 민감도 또한 큰 것으로 나타났다. 이러한 요소는 정밀성이 요구되는 광학분야에 복합재 반사경의 적용을 어렵게 할 커다란 문제점으로 인식되며, 이러한 복합재료의 이방성 성질로 인한 필연적인방사형 방향으로의 강성계수의 변화 및 그 영향성을 줄이기 위해서는 단섬유나 무작위로 공간에 흩어져있는 섬유 복합재료를 사용하는 것이 복합재 반사경내에 존재하는 굽힘강성 계수의 변화를 제거하는 하나의 방법이다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1274-1277
• /
• 2004

The objective of this research work is to investigate into characteristics of bending stiffness and failure for the ISB ultra-lightweight panel with internally structured material. The expanded metal with a pyramid shape and woven metal are employed as an internally structured material. In order to investigate the characteristics, the specific stiffness and failure map are estimated using the results of three-points bending test. From the results of the experiment, the influence of design parameters of ISB panel on the specific stiffness and failure mode has been found. In addition, it has been shown that ISB panel with expanded metal is prefer to that with woven metal from the view point of optimal design for ISB panel.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.162-172
• /
• 2005

The objective of this research works is to investigate into characteristics of bending stiffness and failure for the ISB ultra-lightweight panel with internally structured material. The expanded metal with a crimped pyramid shape and woven metal are employed as an internally structured material. Through three-points bending test, the force-displacement curve and failure shape are obtained to examine the deformation pattern, characteristic data, such as maximum load, displacement at maximum load, etc, and failure pattern of the ISB panel. In addition, the influence of design parameters fur ISB panel on the specific stiffness, the specific stiffness per unit width, failure mode and failure map has been found. Finally, it has been shown that ISB containing expand metal with the crimped pyramidal shape is prefer to that containing woven metal from the view point of optimal design for ISB panel.