• Journal of Advanced Research in Ocean Engineering
• /
• 제4권4호
• /
• pp.174-184
• /
• 2018

We herein propose a new design procedure of a flexible container ship model where the vertical bending and torsional vibration modes are similar to its prototype. To achieve similarity in torsional vibration mode shapes, the height of the shear center of the model must be located below the bottom hull, similar to an actual container ship with large opening decks. Therefore, we designed a ship model by imparting appropriate stiffness to the hull, using urethane foam without a backbone. We built a container ship model according to this design strategy and validated its dynamic elastic properties using a decay test. We measured wave-induced structural vibrations and present the results of tank experiments in regular and freak waves.

• 한국도로학회논문집
• /
• 제14권5호
• /
• pp.47-55
• /
• 2012

PURPOSES: SUPERPAVE binder grade tests including Multiple Stress Creep and Recovery(MSCR) test are applied to evaluate rheological properties of four polymer modified binders. METHODS: To evaluate grade of four modified binders, PG testing protocols, such as DSR, BBR and MSCR are employed. RESULTS: It is observed that MSCR test shows different performance grades especially on modified binders. Both DMP and EG binder show similar high temperature performance to SBS 5% modified binder. CONCLUSIONS: Binder Grading system in Korea need to be reviewed to properly reflect the performnace of modified binders. The binders modified with DMP and EG can be possible alternatives SBS 5% modified binder considering its performance and cost.

• Steel and Composite Structures
• /
• 제43권2호
• /
• pp.139-152
• /
• 2022

Steel-reinforced concrete (SRC) L-shaped column is the vertical load-bearing member with high spatial adaptability. The seismic behavior of SRC L-shaped column is complex because of their irregular cross sections. In this study, the hysteretic performance of six steel truss reinforced concrete L-shaped columns specimens under the combined loading of compression, bending, shear, and torsion was tested. There were two parameters, i.e., the moment ratio of torsion to bending (γ) and the aspect ratio (column length-to-depth ratio (φ)). The failure process, torsion-displacement hysteresis curves, and bending-displacement hysteresis curves of specimens were obtained, and the failure patterns, hysteresis curves, rigidity degradation, ductility, and energy dissipation were analyzed. The experimental research indicates that the failure mode of the specimen changes from bending failure to bending-shear failure and finally bending-torsion failure with the increase of γ. The torsion-displacement hysteresis curves were pinched in the middle, formed a slip platform, and the phenomenon of "load drop" occurred after the peak load. The bending-displacement hysteresis curves were plump, which shows that the bending capacity of the specimen is better than torsion capacity. The results show that the steel truss reinforced concrete L-shaped columns have good collapse resistance, and the ultimate interstory drift ratio more than that of the Chinese Code of Seismic Design of Building (GB50011-2014), which is sufficient. The average value of displacement ductility coefficient is larger than rotation angle ductility coefficient, indicating that the specimen has a better bending deformation resistance. The specimen that has a more regular section with a small φ has better potential to bear bending moment and torsion evenly and consume more energy under a combined action.

• Steel and Composite Structures
• /
• 제16권2호
• /
• pp.221-231
• /
• 2014

The purpose of this study was to evaluate the cyclic behavior of steel column-tree moment connections used in steel moment resisting frames. These connections are composed of shop-welded stub beam-to-column connection and field bolted beam-to-beam splice. In this study, the effects of beam splice length on the seismic performance of column-tree connections were experimentally investigated. The change of the beam splice location alters the bending moment and shear force at the splice, and this may affect the seismic performance of column-tree connections. Three full-scale test specimens of column-tree connections with the splice lengths of 900 mm, 1,100 mm, and 1,300 mm were fabricated and tested. The splice lengths were roughly 1/6, 1/7, 1/8 of the beam span length of 7,500 mm, respectively. The test results showed that all the specimens successfully developed ductile behavior without brittle fracture until 5% radians story drift angle. The maximum moment resisting capacity of the specimens showed little differences. The specimen with the splice length of 1,300 mm showed better bolt slip resistance than the other specimens due to the smallest bending moment at the beam splice.

• 대한기계학회논문집A
• /
• 제36권4호
• /
• pp.443-449
• /
• 2012

Ti-6Al-4V 재에 다양한 표면처리방법을 통하여 나노스킨화된 피로시험편을 제작하고 회전굽힘피로 시험과 축하중 인장압축피로시험을 수행하였다. 특히 S-N 곡선에서 초음파나노표면개질(UNSM)법은 국내특허기술로 다른 처리법들보다 우수한 결과를 보였고, UNSM 처리된 직경 5 mm 재는 6 mm 티타늄재를 대치 가능할 성능을 얻었다. UNSM 처리된 $10^6$ 사이클 이상의 장수명영역에서 피로강도가 크게 향상되는 시험결과를 얻었다. 균열발생 패턴의 분석을 통하여 Ti-6Al-4V 재는 응력의 작용형태에 따라 표면균열발생형(surface originating crack type)과 내부균열발생형(interior originating crack type)인 어안균열(fish eye crack)이 발생하는 메커니즘을 분석하였다.

• 한국응용과학기술학회지
• /
• 제36권1호
• /
• pp.200-207
• /
• 2019

본 연구에서는 "이온젤"이라고 불리는 고분자 기반의 PVA(polyvinyl alcohol)-$H_3PO_4$의 고체 전해질에 이온성 액체 $BMIMBF_4$ (1-buthyl-3-methylimidazolium tetrafluoroborate)를 첨가하여 제조한 전고체 전해질과 환원된 그래핀 옥사이드/전도성 고분자 복합재료 기반의 전극 재료를 이용하여 유연성을 갖는 슈퍼커패시터를 제작 하였으며, 유연성에 따른 전기화학적 특성을 분석하여 보았다. 환원된 그래핀 옥사이드/전도성 고분자 복합재료와 전고체 전해질 기반의 유연성 슈퍼커패시터의 전기화학적 특성을 유연성에 따라서 측정하기 위해서 프레스로 $0.01kg/cm^2$의 일정한 압력으로 최대 100회 까지 굽힘 시험(bending test)을 진행 하였으며, 0~100 회의 굽힘 시험 이후에 순환 전압전류법(CV), 전기화학적 임피던스 분광법(EIS) 및 전정류 충 방전법(GCD)을 통하여 비교 및 분석하여 보았다. 그 결과로, 유연성 슈퍼커패시터의 초기 전기용량은 43.9 F/g으로 확인 할 수 있었고, 이 값은 50회, 100회의 굽힘 시험 후에 각각 42.0F/g, 40.1F/g로 감소하는 현상을 확인할 수 있었다. 이러한 결과로 미루어 보아 물리적인 응력이 슈퍼 커패시터의 전기화학적 특성 감소에 영향을 주는 것으로 사료되며 또한, 굽힘 횟수에 따른 슈퍼커패시터의 전기화학적 특성 감소 원인을 확인하기 위해서 굽힘 시험 전과 후의 전극표면을 전자주사 현미경으로 관찰하여 보았다.

• Steel and Composite Structures
• /
• 제48권1호
• /
• pp.43-57
• /
• 2023

The impacts of waste tire rubber (WTR) on the bending conduct of reinforced concrete beams (RCBs) are investigated in visualization of experimental tests and 3D finite element model (FEM) using both ANSYS and SAP2000. Several WTR rates are used in total 4 various full scale RCBs to observe the impact of WTR rate on the rupture and bending conduct of RCBs. For this purpose, the volumetric ratios (Vf) of WTR were chosen to change to 0%, 2.5%, 5% and 7.5% in the whole concrete. In relation to experimental test consequences, bending and rupture behaviors of the RCBs are observed. The best performance among the beams was observed in the beams with 2.5% WTR. Furthermore, as stated by test consequences, it is noticed that while WTR rate in the RCBs is improved, max. bending in the RCBs rises. For test consequences, it is clearly recognized as WTR rate in the RCB mixture is improved from 0% to 2.5%, deformation value in the RCB remarkably rises from 3.89 cm to 7.69 cm. This consequence is markedly recognized that WTR rates have a favorable result on deformation values in the RCBs. Furthermore, experimental tests are compared to 3D FEM consequences via using ANSYS software. In the ANSYS, special element types are formed and nonlinear multilinear misses plasticity material model and bilinear misses plasticity material model are chosen for concrete and compression and tension elements. As a consequence, it is noticed that each WTR rates in the RCBs mixture have dissimilar bending and rupture impacts on the RCBs. Then, to observe the impacts of WTR rate on the constructions under near-fault ground motions, a reinforced-concrete building was modelled via using SAP2000 software using 3-D model of the construction to complete nonlinear static analysis. Beam, column, steel haunch elements are modeled as nonlinear frame elements. Consequently, the seismic impacts of WTR rate on the lateral motions of each floor are obviously investigated particularly. Considering reduction in weight of structure and capacity of the members with using waste tire rubber, 2.5% of WTR resulted in the best performance while the construction is subjected to near fault earthquakes. Moreover, it is noticeably recognized that WTR rate has opposing influences on the seismic displacement behavior of the RC constructions.

• 한국전산구조공학회논문집
• /
• 제33권2호
• /
• pp.137-144
• /
• 2020

본 논문에서는 시공단계에서 서포트가 필요 없는 UHPC 충전형 상현재를 활용한 트러스 데크플레이트 시스템을 제안하고자 한다. 제안된 시스템은 기존의 시스템과 동일한 절대 층고를 유지하면서 증대된 강성과 강도를 보유하며 효과적으로 처짐을 제어한다. 제안된 시스템 및 기존의 시스템의 구조 성능을 평가하기 위해 4.6m의 순 스팬을 갖는 5개의 실험체를 제작하였고 점진적으로 하중을 증가시키며 4점 휨 실험을 수행하였다. 실험을 토대로 실험체별 하중-처짐 그래프를 도출하였고 변수에 따른 비교 및 분석을 진행하였다. 그리고 실험을 기준으로 수행한 비선형 3차원 유한요소해석결과와의 비교를 진행하였다. 비교 및 분석 결과, 기존의 트러스 데크플레이트를 제외한 모든 실험체들이 시공단계 하중에서 건축구조설계기준 및 강구조설계기준에서 제한하는 처짐 기준을 만족하였으며, 실험과 유한요소해석의 결과가 서로 유사한 것을 확인하였다.

• 터널과지하공간
• /
• 제31권6호
• /
• pp.428-439
• /
• 2021

뿜칠 멤브레인은 폴리머로 구성된 재료로서 지보 또는 차수 목적으로 기존 방수포와 같은 재료를 대체 할 수 있을 것으로 기대되는 뿜어 붙이는 방식의 재료이다. 이전의 해외 연구에서 기존 시멘트계 지보 재료들에 추가로 뿜칠 멤브레인을 시공할 경우 숏크리트와 같은 지보재의 시공 두께를 줄일 수 있을 것으로 기대하고 있으나 국내에서는 아직까지 실험이나 분석 결과가 많이 보고되고 있지 못하다. 본 연구에서는 고성능 숏크리트에 뿜칠 멤브레인을 바깥면에 타설하여 3점 휨시험을 수행하고 고성능 숏크리트와 뿜칠 멤브레인이 시공된 경우를 비교하여 분석하였다. 실내 표준 시험과 실대형 휨시험을 통해 산정된 값을 서로 비교한 결과 휨강도 측면에서는 큰 차이를 보이지 않았으나 휨인성 부분에서 차이를 보이는 것으로 나타났다.

• 한국지진공학회논문집
• /
• 제20권1호
• /
• pp.71-77
• /
• 2016

In this study, the seismic performance of connections between filled composite beam (CG beams) and forming angle composite (FAC) column was experimentally evaluated. First, the bending tests were conducted on two CG beams and the axial tests were conducted on two FAC columns. Then, based on these preliminary test results, the cyclic loading test were performed on two interior connections between CG beam and FAC column. The main difference of two specimens is the plate shape of the CG beam. The test results showed that both specimens achieved the maximum story drift capacity over 0.04 radian which is required for special moment frame.