• International Journal of Safety
• /
• 제10권1호
• /
• pp.16-21
• /
• 2011

In this thesis, appearance inspection, compressive strength of concrete test, arrangement of bar inspection, survey, and bearing stress analysis were performed on a damaged coping of reinforced concrete pier to investigate the damage cause. According to the performed a series of inspections, it was found that the coping of pier was damaged during PSC (Pre-stressed Concrete) beam construction. In this thesis, the repair method for damaged pier was studied. The repair procedure used in this thesis was follows : chipping for damaged part, clean by high-pressure, installation of wire mesh, coating of surface hardening, construction of section restoration material, copula grinding, and prevent coating for far-infrared radiation.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.29-30
• /
• 2011

A Green Frame is a composite Rahmen precast concrete structure that utilizes the advantages of the steel frame and the reinforced concrete. Compared to bearing wall structure, the precast concrete structure may raise construction cost If the precast concrete members are produced in plant. Thus, if the precast concrete members can be produced in site, the cost-effectiveness and quality shall be increased. Various site conditions must be considered and reviewed to ensure a space for the in-situ production. Therefore, this study focuses on the basic study on the arrangement of in-situ production module of composite precast concrete members.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.659-662
• /
• 2009

Railway has been pointed to the efficiency of transportation, rapid transit, and comfortable train ride. the construction of railway near the downtown area and station building are increasing for maximization of utilization and convenience. but the heavy of transportation and rapid transit lead to increase noise and vibration. the noise and vibration of railway may cause the civil appeal, decline in the serviceability and insufficiency of environmental standard. In this study, floating slab system which is one of the solution to avoid noise and vibration in railway has been introduced, and analyzed floating Slab Track into arrangement of reduction material of vibration. As a result of analysis, It was estimated the bearing installation though slab have not a negative factor and terminal arrangement of reduction material of vibration have advantage for static behavior.

• Advances in concrete construction
• /
• 제13권 2호
• /
• pp.153-162
• /
• 2022

Prefabricated exterior wall panel is the main non-load-bearing component of assembly building, which affects the comprehensive performance of thermal insulation and durability of the building. It is of great significance to develop new prefabricated exterior wall panel with durable and lightweight characteristics for the development of energy-saving and assembly building. In the prefabricated sandwich insulation hanging wall panel, the selection of material for the outer layer and the arrangement of the connector of the inner and outer wall layers affect the mechanical performance and durability of the wall panels. In this paper, high performance cement-based composites (HPFRC) are used in the outer layer of the new type wall panel. FRP bars are used as the interface connector. Through experiments and analysis, the influence of the arrangement of connectors on the mechanical behaviors of thin-walled composite wall panel and the panel with window openings under two working conditions are investigated. The failure modes and the role of connectors of thin-walled composite wallboard are analyzed. The influence of the thickness of the wall layer and their combination on the strain growth of the control section, the initial crack resistance, the ultimate bearing capacity and the deformation of the wall panels are analyzed. The research work provides a technical reference for the engineering design of the light-weight thin-walled and durable composite sandwich wall panel.

• 대한토목학회논문집
• /
• 제41권5호
• /
• pp.523-531
• /
• 2021

일반적으로 기초는 여러 개의 단일말뚝이 상부 구조체에 의해 연결된 상태로 군말뚝을 의미한다. 하지만, 군말뚝에 상부 하중 재하 시 지반에 작용하는 응력 범위는 단일말뚝에 비해 더 넓은 폭과 깊이로 확장되고, 중복되기 때문에 전체적인 지지력은 감소할 수 있다. 이러한 지지력 감소비를 군말뚝 효율이라 하나 일반적인 말뚝과 지반의 접촉 조건에 따른 영향을 분석한 연구는 부족한 실정이다. 따라서 본 연구에서는 지반 구성 및 군말뚝의 배치, 간격, 지반과 말뚝간의 접촉 특성을 해석 변수로 설정하고, 군말뚝 효율 및 군말뚝을 구성하는 개별말뚝의 거동을 분석하였다. 해석 결과, 지반 종류에 따라 마찰계수 증가 시 군말뚝 효율은 수렴 또는 감소하는 경향을 보였으며, 이를 통해 최적 군말뚝 효율을 분석하였다. 또한, 개별말뚝 분석을 통한 하중 감소비 파악 결과, 군말뚝 내부에 위치한 말뚝의 경우 하중을 상대적으로 적게 받았으며, 이는 내부 지반에 대한 영향인 것으로 판단된다.

• 한국지진공학회논문집
• /
• 제23권1호
• /
• pp.31-42
• /
• 2019

In this study, the results of an analytical investigation on the seismic behavior of two residential 4-story bearing wall buildings with pilotis, each of which has symmetric or unsymmetric wall arrangement at their piloti level, are presented. The dynamic characteristics and lateral resistance of the piloti buildings were investigated through linear elastic and nonlinear static analyses. According to the results, the analytical natural period of vibration of the piloti buildings were significantly shorter than the fundamental period calculated in accordance with KBC 2016. In the initial elastic behavior, the walls resisting in-plane shear contributed to the lateral stiffness and strength, while the contribution of columns resisting flexural moments in double curvature was limited. However, after the shear cracking and yielding of the walls occurred, the columns significantly contributed to the residual strength and ductility. Based on those investigations, design recommendations of low-rise bearing wall buildings with piloti configuration are given.

• Architectural research
• /
• 제19권4호
• /
• pp.109-115
• /
• 2017

This study is done to evaluate how existence of shear-span ratio and shear reinforcing bar effects on shear performance from through shear experiment using PVA fiber reinforced ferroconcrete building. Ratio of shear-span was set 1, 1.7, and arrangement of shear reinforcing bar was set with KCI2012 regulation. In result, subject with less shear-span ratio, and shear reinforcing bar with arrangement of bar shows high stiffness. Subjects with high shear-span ratio show large difference depending on existence of shear reinforcing bar. Therefore, theoretical shear strength followed by CEB code underestimates experimental shear strength by 43.9%. Shear strength of the deep beam with headed bars is more affected by the bearing strength of head than the bond strength of bar.

• Fisheries and Aquatic Sciences
• /
• 제2권1호
• /
• pp.25-31
• /
• 1999

Developmental morphology of the red alga, Osmundea crispa (Hollenberg) Nam from California was studied on the basis of liquid-preserved and herbarium specimens. Vegetative axial segment of the species produces two pericentral cells and one trichoblast. Spermatangial filaments (branches) are derived from apical and epidermal cells in pocket-shaped apical pit with an ostiole-like upper opening. Procarp-bearing segment of female trichoblast produces five pericentral cells, of which the fifth functions as supporting cell of carpogonial branch. Tetrasporangial production occurs in random epidermal cells in apical pit of branchlets, and two presporangial cover cells show parallel arrangement to stichidial axis. As this vegetative and reproductive development is included in the generic delineation of Osmundea Stackhouse, O. crispa among the known Osmundea species is characterized by habit forming compact cushion-like clump with angular to terete thallus. It is also distinguished from O. hybrida (AP. de Candolle) Nam without the compressed thallus by the number of pericentral cells in procarp-bearing segment and shape of spermatangial pit. Taxonomic implication of the shape of spermatangial pit is also included.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2187-2193
• /
• 2014

In this paper, we propose a method for suppressing shaft voltage by modifying the rotor shape and the permanent magnets in interior permanent magnet type high voltage motors. The shaft voltage, which adversely affects the bearing by occurring bearing current, is induced by parasitic components and the leakage flux in motor-driven systems as well as inherent linkage flux between main magnetic flux and shaft according to rotor configuration. Thus, shaft voltage should be analyzed and considered under inverter-driven and non-inverter-driven conditions because inherent linkage flux can analyze under non-inverter-driven condition. In this study, we designed re-arrangement magnet and re-structuring rotor to minimize the shaft voltage. In addition, we optimized the proposed models. The shaft voltage suppression effect of the designed model was validated experimentally and by comparative finite element analysis.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.46-52
• /
• 2001

One of the important technical issues is how to decrease thermal expansion of ballscrew in proportion to the increase of machining speed. when measuring force of stretch of ballscrew, since not only actual expansion and the value of bending have to be considered, it's impossible to definite the exact value of expansion. In addition, support bearings of ballscrew gain considerable force in axial direction. It also generates thermal expansion on the ballscrew, and deteriorates the bearings. In conclusion, it's impossible to give the pretension enough to absorb the all elongation due to thermal expansion generated during machine running. If gave, bed, column and saddle are all bent to change machine accuracy, and the support bearings of ballscrew are damaged. The purpose of this paper is to study the pretension of support bearing of ballscrew in machine tool.