• 전기학회논문지
• /
• 제64권1호
• /
• pp.196-200
• /
• 2015

The switching noise in the power electronics of the power conversion equipment (Power Conditioning System) for large energy storage devices are generated. Since the burst-level transient noise from being generated in the power system at a higher power change process influences the control circuit of the low voltage driver circuit. Noise may cause the malfunction of the control device even if no dielectric breakdown leads to a control circuit. To overcome this, this paper proposes the installation of an additional nano-surge protection device on the power supply DC output circuit of the battery management unit.

• 한국정보통신학회논문지
• /
• 제16권3호
• /
• pp.541-548
• /
• 2012

본 논문에서는 전기자동차의 보급 확대에 따른 충전 인프라 구축을 위해서 차량의 충전 시 충전상태를 모니터링 할 수 있는 충전 모니터링 시스템의 설계 방법을 제안하였다. 급속충전 기술은 현재 battery의 성능 및 안전성 등 다양한 요인에 따라 동작성능이 좌우되므로 모니터링 시스템에 의한 충전상태 파악은 충전 알고리즘의 개선, 전기자동차 BMS와 연동, 사용자와의 충전 프로세스 제어 등 다양한 작업환경과 연계되어 있다. 급속충전시스템의 동작상태를 CAN 프로토콜을 이용하여 배터리의 충전 상태 등을 실시간으로 감시가 가능한 시스템을 설계 제작하여 전기자동차용 battery를 최단시간에 최적화된 상태로 충전 가능하도록 CAN 통신기반 급속충전 모니터링 시스템을 설계하는 방법을 제안하고 시스템을 구현하여 성능을 확인하였다.

• 한국산학기술학회논문지
• /
• 제13권6호
• /
• pp.2484-2490
• /
• 2012

본 연구는 EV용 전기차동차의 차세대 에너지원인 리튬이온 배터리 팩을 관리하는 BMS의 성능 검증을 위한 시뮬레이터의 Cell simulation 보드와 이를 컨트롤 할 수 있는 임베디드 프로그램을 개발 하였다. 그리고 시뮬레이터의 속도를 향상시키고, 시스템 단가를 낮출 수 있는 Amplifier를 직렬로 연결하는 방식을 고안하여 OP amp와 트랜지스터를 직렬로 연결하였다. 또한, DAC를 채널마다 사용하여 채널간 절연(isolation)성능 을 기존 방식보다 향상 시켰다. 그리고 전류 제한 보호회로를 구성하여, 외란으로부터 보드를 보호 할 수 있도록 하였다. 개발된 시뮬레이터의 성능 검증을 위하여 각 셀에 5V부터 0.5V까지 0.5V의 크기로 전압을 강하 시키면서 총 10번의 실험을 하였다. 실험 데이터의 유의성 분석 결과, 모든 실험 조건에서 평균 0.001~0.004V 표준 편차로 출력되는 것을 확인하였으며, 이를 통하여 본 시뮬레이터가 높은 유의성 및 반복성을 가지는 시스템임을 확인 할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제32권1호
• /
• pp.58-63
• /
• 2019

Lithium-ion batteries used for IT, automobiles, and industrial energy-storage devices have battery management systems (BMS) to protect the battery from abnormal voltage, current, and temperature environments, as well as safety devices like, current interruption device (CID), fuse, and vent to obtain positive temperature coefficient (PTC). Nonetheless, there are harmful to human health and property and damage the brand image of the manufacturer because of smoke, fire, and explosion of lithium battery packs. In this paper, we propose a systematic protection algorithm combining battery temperature, over-current, and interconnection between protection elements to prevent copper deposition, internal short circuit, and separator shrinkage due to frequent and instantaneous over-current discharges. The parameters of the proposed algorithm are suggested to utilize the experimental data in consideration of battery pack operating conditions and malicious conditions.

• 한국전기전자재료학회논문지
• /
• 제31권1호
• /
• pp.61-67
• /
• 2018

High-power lithium batteries are suitable for equipment with high power output needs, such as for ESS's initial start-up. However, their management cost is increased by the installation of air-conditioning to minimize the risk of explosion due to internal temperature rise and also by a restriction on the number of charge/discharge cycles. High-capacity flow batteries, on the other hand, have many advantages. They can be used for over 20 years due to their low management costs, resulting from no risk of explosion and a high number of charge/discharge cycles. In this paper, we propose an ESS based on hybrid batteries that uses a lithium iron phosphate battery (LiFePO) at the initial startup and a vanadium redox flow battery (VRFB) from the end of the transient period, with a bi-directional PCS to operate two batteries with different DC voltage levels and using an efficient energy management control algorithm.

• 한국안전학회지
• /
• 제31권3호
• /
• pp.34-41
• /
• 2016

The purpose of this paper is to conduct ETA on six items of ESS: the whole system, battery, BMS, PCS, ESS and cable. To achieve that, ESS work flow and its components are categorized. Based on performance, human, environmental, management, and safety, this paper drew initiation events (IE) and end states (ES). ETA is applied to the main functions of each item, and the end states that may occur in one initiation event are suggested. In addition, detailed classification was performed to induce various end states on the basis of the suggested initiation events ; loss of grid electricity of ESS, loss of battery electricity(DC) of battery, impairment of electric function of BMS, loss of grid electricity(AC) of PCS, loss of data of EMS, Mechanical damage of cable, event sequence analysis conducted on the basis of event trees. If the suggested IEs and ESs are applied on the basis of ESS event cases, it is expected to prevent the same kinds of accident and operate ESS safely.

• 한국전기전자재료학회논문지
• /
• 제25권11호
• /
• pp.930-937
• /
• 2012

Newly developed Series hybrid low-floor articulated vehicle which can meet both road and railway running conditions. It has the rated driving speed of 80 km/h and three driving modes with hybrid(engine+battery) driving mode, engine driving mode, battery driving mode. The battery driving mode requires the several 10 km running without additional charging operation. The vehicle has been equipped with LPB (lithium polymer battery) pack for the series hybrid propulsion system. LPB pack consists of 168 cells (3.7 V in a cell, 80 Ah) in series, DC Circuit breaker, mechanical rack, BMS (battery management system). This paper has shown the design process of LPB pack and application to the vehicle. Driving results in the road was successful to be satisfied with the requirement of the series hybrid vehicle.

• 대한전자공학회논문지SD
• /
• 제49권3호
• /
• pp.1-7
• /
• 2012

본 논문에서는 모바일 정보기기의 배터리 전력 관리를 제어하는 IBS(Intelligent Battery sensor), BMS(Battery Management System) 등의 PMIC(Power Management IC) 기술에 적합한 9b 2MHz 사이클릭 폴딩 ADC(Analog-to-Digital Converter)를 제안한다. 제안하는 ADC는 응용기술에 적합한 고해상도를 만족시키는 동시에 폴딩 신호처리를 사용함으로써 고속 동작이 가능하다. 또한 폴딩 블록의 하나의 단만을 반복적으로 순환하는 구조로 설계되기 때문에 전체 크기가 줄어들 뿐 아니라 전력소모도 최소화 할 수 있다. 제안하는 시제품 ADC는 0.35um 2P4M CMOS 공정으로 제작되었으며, 측정된 INL 및 DNL은 각각 ${\pm}1.5/{\pm}1.0\;LSB$ 이내로 들어온 것을 확인하였다. 또한 2MS/s 동작 속도에서 SNDR 및 SFDR 이 각각 최대 48dB, 60dB이고, 전력 소모는 3.3V 전원 전압에서 110mW 이며 제작된 ADC의 칩 면적은 $10mm^2$이다.

• 전기학회논문지P
• /
• 제63권1호
• /
• pp.40-45
• /
• 2014

This study examines the system and process of battery stored energy in vehicles and suggest the effective area for the use of V2G(vehicle-to-grid) from Jeju Smart Grid Demonstration Project. V2G means technology of electric power transmission from the battery of electric-drive vehicles to state grid. As for the increasing of effectiveness for demand-side control, V2G is a very good alternative. In the U.S., the utilization of electric vehicles is under 40% on average. In this case, we can use he battery of electric vehicle as role of frequency regulation or generator of demand-side resource. V2G, which is the element of Smart Transportation, consists of electric vehicle battery, BMS(battery management system), OBC(on-board charger), charging infrastructure, NOC(network operating center) and TOC(total operation center). V2G application has been tested for frequency regulation to secure the economical efficiency in the United States. In this case, the battery cycle life is not verified its disadvantage. On the other hand, Demand Response is required by low c-rate of battery in electric vehicle and It can be small impact on the battery cycle life. This paper concludes business area of demand response is more useful than frequency regulation in V2G application of electric vehicles in Korea. This provides the opportunity to create a new business for power grid administrator with VPP(virtual power plant).

• 전기학회논문지
• /
• 제63권8호
• /
• pp.1085-1091
• /
• 2014

A model based SOC estimation scheme using parameter identification is described and applied to a Lithium-ion battery module that can be installed in electric vehicles. Simulation studies are performed to verify the effect of sensor faults on the SOC estimation results for terminal voltage sensor and load current sensor. The sensor faults should be detected and isolated as soon as possible because the SOC estimation error due to any sensor fault seriously affects the overall performance of the BMS. A new fault detection and isolation(FDI) scheme by which the fault of terminal voltage sensor and load current sensor can be detected and isolated is proposed to improve the reliability of the BMS. The proposed FDI scheme utilizes the parameter estimation of an input-output model and two fuzzy predictors for residual generation; one for terminal voltage and the other for load current. Recently developed dual polarization(DP) model is taken to develope and evaluate the performance of the proposed FDI scheme. Simulation results show the practical feasibility of the proposed FDI scheme.