• Journal of Energy Engineering
• /
• v.11 no.3
• /
• pp.254-261
• /
• 2002

The fabrication method for the main components of the polymer electrolyte membrane fuel cell stack such as electrodes, membrane-electrode assemblies, and bipolar plates was established for the effective electrode area of 240 ㎠. A counter-flow type 100-cell stack was fabricated by using the above components and then a maximum power of 7.44 kW for H$_2$/O$_2$ and 5.56 kW for H$_2$/air could be obtained at 70$\^{C}$ and 1 atm. It was seen that the distribution of the OCV for unit cells in the stack was uniform but the voltage deviation increased as the load increased due to the IR drop and the electrode polarization. The stack was applied to the power source of the fuel cell/battery hybrid electric golf car. It produced about 1 kW at a room temperature operation during the test run, which occupied about 43% of the total power required by the 2.3 kW motor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.1
• /
• pp.8-13
• /
• 2012

In this paper, Hybrid Electric Vehicle is directly designed and manufactured for base study of HEV's system and Green Car. Foundation design consists of power train design and the frame design. The power train concept includes motor, engine, generator and battery. And the concept of the frame is the single-seat of this self-made HEV. A frame installed in hybrid system contains suspension, steering wheel, seat, accelerating pedal, brake pedal, clutch handle and various chassis parts with bearings. Electromagnetic clutch is equipped to transmit engine power to drive axle. The control algorism make using LabVIEW to control of an engine and a motor depending on drive condition. A parallel type hybrid system is manufactured to control operation of a motor and an engine depending on vehicle speed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.352-359
• /
• 1999

This paper is a research for removing the alternators hunting which came about during the par-allel running. The four-pole six-phase alternator is equipped with the converter made out of twelve diodes to rectify all the waves. The hunting came about during the battery charging due to the hunting inducing point existed in r. p. m band 1575[rpm-1690[rpm] To remove the hunting inducing point We modified the four-pole six-phase alternator into the four-pole twevel-phase and increased the short-circuit ratio by decreasing the field coil pitch and increasing the field coil turns. But this method has two defects the first the alternator structure becomes complicating and the second the second the alternator equipped with the converter used in general purpose lately such as the car alternator can not be run in parallel wlthout modifying. To remove the defects the equalizing line was connected between the same phase of the alterna-tor to flow the synchronizing current which syncronize the phases of generator electromotive forces by which the alternator can be run in parallel without reference to the hunting inducing point and without modifying.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.471-473
• /
• 2013

This paper is analyzing the situation of the electric vehicle Industry and draw the policy implications to promote electric vehicle industry. Major automobile makers as GM, BMW, Nissan, Audi produce various electric vehicles. But in recent times, only few electric vehicle sold in the world. So, many automobile makers gave up the production of electric vehicles. and the fuel-cell vehicle will replace the electric vehicle as a environment car in the future. We should take the build up of eco system between vehicle makers and the small parts companies, construction of battery charging infrastructure, promotion of standardization activities, and the government's support to revive the electric vehicle industry.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.6
• /
• pp.738-745
• /
• 2014

Recently, various measures have been discussed for overcoming depletion of fossil fuels and environmental pollution. One of the measures is electric vehicles. But electric vehicles has some limitations from high cost of battery and low efficiency, so operation distance of electric cars is limited. Also there are difficulties that charging lines should be connected by an electric car whenever it charges. Thus, many studies have been conducted to overcome the limitation using conventional batteries of electric vehicles. As a result, the OLEV(On-Line Electric Vehicle) was developed. But the OLEV system is some limitations. The OLEV system causes power quality problems when it charges. Power quality problem cannot be ignored because OLEV systems are closely connected by distribution grids. In this paper, the OLEV system is designed by using PSCAD/EMTDC, and the power quality is measured and evaluated. Power quality is divided by two cases; harmonics and high-frequency. Harmonics were evaluated according to IEEE Std. 519-1992. But the evaluation of High-frequency could not take it because there was no standard. For this reason, the data measured by OLEV system was compared with the EN50065 regulation.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1792-1798
• /
• 2017

Event Data Recorder(Car Black-Box) with WiFi dongle have been released, and the platform of the majority is the Linux platform. This is because the platform development is possible in little investment cost by reducing the source licensing costs by taking advantage of the open source. But utilizing Linux platform has the limitations of boot-up time and consuming processing power due to the limitation of battery capacity, to be cost-competitive to minimize the use of memory. In this paper, the real-time operating system(RTOS) is utilized to optimize these portions. MP4 encoder and Muxer are developed to be about ten seconds boot up and minimized memory. It has the advantages of operating at lower power consumption than the Linux utilizing WiFi dongle. Utilizing a WiFi dongle is to provide a progressive download feature on smart phones to lower product prices. But RTOS has the weakness in WiFi. Porting TCP /IP, Web and DHCP server and combination with the USB OTG Host interface by implementing the protocol stack are developed for WiFi. And also SPI NOR flash memory is utilized for faster boot time and cost reductions, low processing power to be consume. As the results, the developed proved the 10 seconds booting time, 24 frame rate/sec. and 10% lower power consumption.

• Journal of Information Processing Systems
• /
• v.16 no.3
• /
• pp.677-687
• /
• 2020

This paper deals with the electrical shock that can occur in a car wireless charging system. The recently released the Wireless Power Consortium (WPC) standard specifies that the receiver must be protected from the radio power generated by the transmitter and presents two scenarios in which the receiver may be subjected to electrical shock due to the wireless power generated by the transmitter. The WPC also provides a hardware approach for blocking the wireless power generated by the transmitter to protect the receiver in each situation. In addition, it presents the hardware constraints that must be applied to the transmitter and the parameters that must be constrained by the software. In this paper, we analyze the results of the electric shock in the vehicle using the WPC certified transmitter and receiver in the scenarios presented by WPC. As a result, we found that all the scenarios had electrical shocks on the receiver, which could have a significant impact on the receiver circuitry. Therefore, we propose wireless power transfer limit (WPTL) algorithm to protect receiver circuitry in various vehicle charging environments.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.8 no.2
• /
• pp.89-94
• /
• 2014

This research notes dramatic increase of wheelchair usage along with rapidly aging population and handicapped people in Korea. Differentiated from existing electronic wheelchairs, we have invented an electronic wheelchair that is collapsible even when the battery is installed and a guardian can ride along with a patient. It is also easy to put in a small space such as car trunks. Additionally, we have improved stoic design to be preferable for patients. The model ensures there's neither abrupt acceleration nor sudden stop and, lastly, is much cheaper than other imported models.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.05a
• /
• pp.503-506
• /
• 2014

This research notes dramatic increase of wheelchair usage along with rapidly aging population and handicapped people in Korea. Differentiated from existing electronic wheelchairs, we invented an electronic wheelchair that is collapsible even when the battery is installed and a guardian can ride along with a patient, It is also easy to put in a small space such as car trunks. We simulated to wheelchair body for Stress, Strain, fatigue Analysis. Additionally, we improved stoic design to be preferable for patients. The model ensures there's neither abrupt acceleration nor sudden stop and lastly, is much cheaper than other imported models.

• Transactions of Materials Processing
• /
• v.32 no.6
• /
• pp.367-375
• /
• 2023

Composite materials, known for their excellent mechanical properties and lightweight characteristics, are applied in various engineering fields. Recently, efforts have been made to develop an automotive battery protection panel using a plain-woven composite composed of glass fiber and polypropylene to reduce the weight of automobiles. However, excessive warpage occurs during the GF/PP compression molding process, which makes car assembly challenging. This study aims to develop a model that predicts the warpage during the compression molding process. Obtaining out-of-plane properties such as elastic or shear modulus, essential for predicting warpages, is tricky. Existing mechanical methods also have limitations in calculating these properties for woven composite materials. To address this issue, finite element analysis is conducted using representative volume elements (RVE) for woven composite materials. A warpage prediction model is developed based on the estimated physical properties of GF/PP composite materials obtained through representative volume elements. This model is expected to be used for reducing warpages in the compression molding process.