• Economic and Environmental Geology
• /
• v.42 no.5
• /
• pp.413-426
• /
• 2009

The study was conducted to investigate the effects of indigenous bacteria on geochemical behavior of toxic heavy metals in contaminated paddy soil near an abandoned mine. The effects of sulfate amendment to stimulate microbial sulfate reduction on heavy metal behaviors were also investigated. Batch-type experiments were performed with lactate or glucose as a carbon source to activate indigenous bacteria in the soil under anaerobic condition for 100 days. Sulfate (250 mg/L) was artificially injected at 60 days after the onset of the experiments. In the case of glucose supply, solution pH increased from 4.8 to 7.6 while pH was maintained at 7~8 in the lactate solution. The initial low pH in the case of glucose supply likely resulted in the enhanced extraction of Fe and most heavy metals at the initial experimental period. Lactate supply exerted no significant difference on the amounts of dissolved Zn, Pb, Ni and Cu between microbial and abiotic control slurries; however, lower Zn, Pb and Ni and higher Cu concentrations were observed in the microbial slurries than in the controls when glucose supplied. Sulfate amendment led to dramatic decrease in dissolved Cr and maintenance of dissolved As, both of which had gradually increased over time till the sulfate injection. Black precipitates formed in solution after sulfate amendment, and violarite($Fe^{+2}{Ni^{+3}}_2S_4$) was found with XRD analysis in the microbial precipitates. Conceivably the mineral might be formed after Fe(III) reduction and microbial sulfate reduction with coprecipitation of heavy metal. The results suggested that heavy metals which can be readily extracted from contaminated paddy soils may be stabilized in soil formation by microbial sulfate reduction.

• The Korean Journal of Pesticide Science
• /
• v.4 no.3
• /
• pp.82-88
• /
• 2000

The objective of this study was to determine if wood vinegar of Quercus mongolica Fisch has herbicidal activity. Growth of plants, such as barnyard grass (Echinochloa crus-gulli P. Beauv), quackgrass (Agropyron smithii RYDB), canola (Brassica napus L.), velvetleaf (Abutilon avicennae), indian jointvetch (Aeschynomene indica), and common sorghum (Sorghum bicolor) grown on agar batch treated with 0.01% wood vinegar were similar to that of plant without wood vinegar. The growth of such plants, however, reduced at $0.1{\sim}1%$ concentrations, and inhibited totally at >5% concentration. In greenhouse study, soil-applied wood vinegar did not inhibit tile growth of canola, barnyard grass, large crabgrass, and Abutilon avicennae even at the highest concentration, 80L $80L^{-1}\;10a^{-1}$, while foliar-applied wood vinegar did inhibit the growth of plants at higher than 40L $80L^{-1}\;10a^{-1}$. Growth of canola, barnyard grass, large crabgrass, and Abutilon avicennae treated with wood vinegar (80L $80L^{-1}\;10a^{-1}$) was reduced by 71, 46, 24, and 47%, respectively. In field experiment conducted at Chunchon and Taebeck, biomass of weeds treated with wood vinegar at less than 40L $80L^{-1}\;10a^{-1}$ were close to that of weeds treated without wood vinegar, while biomass of weeds at 80L $80L^{-1}\;10a^{-1}$ was reduced by 34-36%, compared to that of control, at both sites. However, the herbicidal activity of wood vinegar was much lower than that of glyphosate. Results in this study show that wood vinegar of Quercus mongolica Fisch has herbicidal activity, although the herbicidal activity was lower than that of glyphosate, a commercial herbicide.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.8
• /
• pp.367-377
• /
• 2017

This study examined the effects of the salinity of seafood wastewater on the sulfur denitrification process. An examination of the denitrification efficiency showed that the optimal EBCT was 1hr at an influent T-N concentration of 20mg/L or lower and 2-3hr at an T-N concentration of 30mg/L. An examination of the denitrification efficiency according to the nitrogen load showed that the legal effluent water quality criterion was satisfied when the influent load was maintained within $0.496kg/m^3/day$. On the other hand, the reactor volume increased when this was applied to the site. Therefore, the influent load should be within $0.372kg/m^3/day$ considering the denitrification and economic efficiency. At a load of $0.248{\sim}0.628kg/m^3{\cdot}day$, the k value was $0.0890{\sim}0.5032hr^{-1}$. The batch experimental results according to the $Cl^-$ concentration showed that at an influent nitrogen concentration of 30.0mg/L, the effect of the denitrification efficiency was not large below the salinity of $7,000mgCl^-/L$, but inhibition occurred above $9,000mgCl^-/L$. Calculations of the reaction rate constant according to the $Cl^-$ concentration showed that the reaction rate constant was $0.1049{\sim}0.2324hr^{-1}$ at a raw wastewater concentration of ${\sim}5,000mgCl^-/L$. In contrast, the k value was $0.1588hr^{-1}$ at $7,000mgCl^-/L$ and $0.1049hr^{-1}$ at $9,000mgCl^-/L$.

• Journal of Marine Bioscience and Biotechnology
• /
• v.1 no.2
• /
• pp.105-118
• /
• 2006

Isolation and Identification of fatty acid and volatile compounds in tuna fish oil were successfully carried out using supercritical carbon dioxide. Samples of the oil were extracted in a 56 ml semi-batch stainless steel vessel under conditions which ranged from 80 to 200 bar and 40 to $60^{\circ}C$ with carbon dioxide flows from 10 ml/min. Volatiles in the oil extracted from the samples with supercritical carbon dioxide were analyzed by gas chromatography, mass detector with canister system. The extracts were contained with various fatty acids, 57.0% of unsaturated fatty acids such as docosahexaenoic acid(DHA) and eicosapentaenoic acid(EPA), and 43.0% of saturated fatty acids. The aroma compounds in the oil showed over 129 peaks, of which 100 compounds were identified. Volatile components included 2,4-hepatadienal(fishy), dimethyldisulfide (unpleasant), dimethyltrisulfide (unpleasant) and 2-nonenal(fatty). The isolation efficiency of the volatile compounds from the samples was 99.4% at $50^{\circ}C$ and 200 bar.

• FLOWER RESEARCH JOURNAL
• /
• v.17 no.1
• /
• pp.1-8
• /
• 2009

This study was conducted to investigate the efficiency of water quality remediation and the inorganic ion removal characteristics by floating plant; water lettuce (Pistia stratiotes L.) in a batch reactor. Water lettuce can be used to remove N and P and other inorganic nutrients, by consuming them in the form of plant nutrient. The highest nutrient absorption of water lettuce was $112.5meL^{-1}\;N$ in Sonneveld-2S, $56.6meL^{-1}\;N$ in Sonneveld-1S, $31.8meL^{-1}\;N$ in sewage and P value was also the highest in Sonneveld-2S as $15.6meL^{-1}$ and in sewage as $5.0meL^{-1}$. These results indicated that using water lettuce held some promise in the context of purification of eutrophication. Also water lettuce had a preference for absorption N. Under Sonneveld-2S treatment, nitrogen percentage was the highest in plant tissue due to the highest concentration of nitrogen and removal by water lettuce. Under sewage, percentage of total N in both plant parts was high. Both above and underground parts, P percentage was less than N. It might be due to the fact that the absorption amount of P was less than N by water lettuce. It meaned that the ability of N removal by water lettuce was higher than that of P, relatively. In summary, these results show that the use of this plant was a viable option.

• Journal of Soil and Groundwater Environment
• /
• v.14 no.4
• /
• pp.23-32
• /
• 2009

The sorption of europium (Eu (III)) onto kaolinite and the influence of humic acids over a range of pH 3 ~ 11 has been studied by batch adsorption experiment (V/m = 250 : 1 mL/g, $C_{Eu(III)}\;=\;1\;{\times}\;10^{-5}\;mol/L$, $C_{HA}\;=\;5{\sim}50\;mg/L$, $P_{CO2}=10^{-3.5}\;atm$). The concentrations of HA and Eu(III) in aqueous phase were measured by UV absorbance at 254nm (e.g., $UV_{254}$) and ICP-MS after microwave digestion for HA removals, respectively. Results showed that the HA sorption onto kaolinite was decreased with increasing pH and their sorption isotherms fit well with the Langmuir adsorption model (except pH 3). Maximum amount ($q_{max}$) for the HA sorption at pH 4 to 11 was ranged from 4.73 to 0.47 mg/g. Europium adsorption onto the kaolinite in the absence of HA was typical, showing an increases with pH and a distinct adsorption edge at pH 3 to 5. However in the presence of HA, Eu adsorption to kaolinite was significantly affected. HA was shown to enhance Eu adsorption in the acidic pH range (pH 3 ~ 4) due to the formation of additional binding sites for Eu coming from HA adsorbed onto kaolinite surface, but reduce Eu adsorption in the intermediate and high pH above 6 due to the formation of aqueous Eu-HA complexes. The results on the ternary interaction of kaolinte-Eu-HA are compared with those on the binary system of kaolinite-HA and kaolinite-Eu and adsorption mechanism with pH was discussed.

• Journal of the Korean Society of Radiology
• /
• v.15 no.6
• /
• pp.919-926
• /
• 2021

In this study, we wanted to find out the optimal angle as a modified tangential projection of the patella. In the experiment, we used Kyoto Kagaku's PBU-50 phantom. In the supine position, the F-T angle was set to 95°, 105°, 115°, 125°, 135°, 145°, and Patella tangential projection images were obtained by varying the X-ray tube angle by 5° so that the angle between the X-ray centerline and tibia at each angle was 5~20°. Image J was used for image analysis and the congruence angle, lateral patellofemoral angle, patellofemoral index and contrast to noise ratio(CNR) were also measured. SPSS 22 was used for statistical analysis, and the mean values of congruence angle, patellofemoral angle, patellofemoral index, and CNR were compared with Merchant method through one-way batch analysis and corresponding sample t-test. As a result of the study, in the case of congruence angle, the angle of incidence of the knee-angle X-ray centerline was 105°-72.5° (20° tangential irradiation), 115°-72.5°, 77.5° (15, 20° tangential irradiation), 125°-82.5° (20° tangential irradiation), lateral patellofemoral angle is 115°-72.5°, 77.5° (15, 20° tangential irradiation), 125°-72.5° (10° tangential irradiation), patellofemoral index is 115°-72.5° (15° tangential irradiation) and 125°-72.5° (10° tangential irradiation) were not significantly different from Merchant method (p> .05). In case of CNR, it is not different from Merchant method at 105°-67.5°, 72.5° (15, 20° tangential irradiation), 115°-67.5°, 72.5°, 77.5° (10, 15, 20° tangential irradiation). (P> .05). Based on the results of this study, high diagnostic value images can be obtained by setting the knee angle and the angle of incidence of the X-ray tube to 115°-72.5° (15° tangential irradiation) during the modified tangential examination of the knee bone. It was confirmed.

• Food Engineering Progress
• /
• v.14 no.3
• /
• pp.208-216
• /
• 2010

Lab scale experiments were conducted in order to assess the applicability of $CaCO_{3}$-alginate beads as neutralizer for the high cell density cultivation and prepare the direct vat inoculation cultures of isolated sourdough lactic acid bacteria. With increasing the amount of bead and decreasing the diameter of bead in acidic solution, the neutralizing effect of $CaCO_{3}$-alginate bead became higher. In batch process with $CaCO_{3}$-alginate beads, Lactobacillus amylovorus DU-21 isolated from sourdough showed the highest viable cell counts and optical density in MRS broth. The values of viable cell counts and optical density were 9.996 log CFU/mL and 3.97, respectively. Experiments on the conditions which increase viability during lyophilization were carried out and the following results were obtained; 15% glycerol revealed the high cryoprotective effect on the concentrated cultures during lyophilization among the two cryoprotective agents. Consequently, $CaCO_{3}$-alginate beads and 15% glycerol were found to be useful not only to cultivate Lactobacillus amylovorus DU-21 but also to preserve strain.

• Clean Technology
• /
• v.25 no.1
• /
• pp.91-97
• /
• 2019

Oxidative desulfurization (ODS) has received much attention in recent years because refractory sulfur compounds such as dibenzothiophenes can be oxidized selectively to their corresponding sulfoxides and sulfones, and these products can be removed by extraction and adsorption. In this work, The oxidative desulfurization of marine diesel fuel was performed in a batch reactor with hydrogen peroxide ($H_2O_2$) in the presence of various supported heteropoly acid catalysts. The catalysts were characterized by XRD, XRF, XPS and nitrogen adsorption isotherm techniques. Based on the sulfur removal efficiency of promising silica supported heteropoly acid catalysts, the ranking of catalytic activity was: $30\;H_3PW_{12}/SiO_2$ > $30\;H_3PMo_{12}/SiO_2$ > $30\;H_4SiW_{12}/SiO_2$, which appears to be related with their intrinsic acid strength. The $30\;H_3PW_{12}/SiO_2$ catalyst showed the highest initial sulfur removal efficiency of about 66% under reaction conditions of $30^{\circ}C$, $0.025g\;mL^{-1}$ (cat./oil), 1 h reaction time. However, through the recycle test of the $H_3PW_{12}/SiO_2$ catalyst, significant deactivation was observed, which was attributed to the elution of the active component $H_3PW_{12}$. By introducing cesium cation ($Cs^+$) into the $H_3PW_{12}/SiO_2$ catalyst, the stability of the catalyst was improved with changing the solubility, and the $Cs^+$ ion exchanged catalyst could be recycled for at least five times without severe elution.

• Economic and Environmental Geology
• /
• v.52 no.1
• /
• pp.1-12
• /
• 2019

Batch experiments for the soil washing coupled with the magnetic separation process were performed to remediate the soil contaminated with metal and oil wastes. The soil was seriously contaminated by Zn and TPH (total petroleum hydrocarbon), of which concentrations were 1743.3 mg/kg and 3558.9 mg/kg, respectively, and initial concentrations of Zn, Pb, Cu, and TPH were higher than the 2nd SPWL (soil pollution warning limit: remediation goal). The soil washing with acidic solution was performed to remove heavy metals from the soil, but Pb and Zn concentration of the soil maintained higher than the 2nd SWPL even after the soil washing with acidic solution. The 2nd soil washing was repeated to increase the Pb and Zn removal efficiency and the Zn and Pb removal efficiencies additionally increased by only 8 % and 5 %, respectively, by the 2nd soil washing (> 2nd SPWL). The small particle separation from the soil was conducted to decrease the initial concentration of heavy metals and to increase the washing effectiveness before the soil washing and 4.1 % of the soil were separated as small particles (< 0.075 mm in diameter). The small particle separation lowered down Zn and Pb concentrations of soil to 1256.3 mg/kg (27.9 % decrease) and 325.8 mg/kg (56.3 % decrease). However, the Zn concentration of soil without small particles still was higher than the 2nd SPWL even after the soil washing, suggesting that the additional process is necessary to lower Zn concentration to below the 2nd SPWL after the treatment process. As an alternative process, the magnetic separation process was performed for the soil and 16.4 % of soil mass were removed, because the soil contamination was originated from unreasonable dumping of metal wastes. The Zn and Pb concentrations of soil were lowered down to 637.2 mg/kg (63.4 % decrease) and 139.6 mg/kg (81.5 % decrease) by the magnetic separation, which were much higher than the removal efficiency of the soil washing and the particle separation. The 1st soil washing after the magnetic separation lowered concentration of both TPH and heavy metals to below 2nd SPWL, suggesting that the soil washing conjugated with the magnetic separation can be applied for the heavy metal and TPH contaminated soil including high content of metal wastes.