• ETRI Journal
• /
• v.26 no.6
• /
• pp.657-660
• /
• 2004

We propose a fine phase tuner and a rounding processor for a numerically controlled oscillator (NCO), yielding a reduced phase error in generating a digital sine waveform. By using the fine phase tuner presented in this paper, when the ratio of the desired sine wave frequency to the clock frequency is expressed as a fraction, an accurate adjustment in representing the fractional value can be achieved with simple hardware. In addition, the proposed rounding processor reduces the effects of phase truncation on the output spectrum. Logic simulation results of the NCO using these techniques show that the noise spectrum and mean square error (MSE) for eight output bits of a 3.125 MHz sine waveform are reduced by 8.68 dB and 5.5 dB, respectively, compared to those of the truncation method, and 2.38 dB and 0.83 dB, respectively, compared to those of Paul's scheme.

• Journal of the military operations research society of Korea
• /
• v.6 no.2
• /
• pp.27-46
• /
• 1980

Computer model for calculating the maximum detection range of the pulse radar used for surface surveillance is developed, and the detailed procedures of each theoretical step are discussed. The quantity of radar antenna's receiving energy, transmitting energy and noise level are compared in this model. All the calculation steps are programmed in BASIC language. Finally, I have found the output of this model well matched with the some experimental results.

• Journal of the Korean Solar Energy Society
• /
• v.27 no.1
• /
• pp.55-61
• /
• 2007

This paper describes the procedure and calculation results of basic design and transient variation of performance of 1 MWe large scale solar thermal power plant (STPP) by using the commercial software of THERMOFLEX and TRNSYS, respectively. In order to simulate the transient variation of STPP, the results of basic design are necessary. The design standard of the STPP is 1 MWe generation with solar only at high DNI condition and then 0.6 MWe output power for 1 hour using stored energy when the DNI becomes lower unable to operate normally. The results of basic design show the important design data of flow rates, water/steam conditions at each equipments and the estimated efficiency of STPP. In addition, dynamic simulation results of STPP are predicted and plotted for one year and three different days weather data of Daejeon.

• Economic and Environmental Geology
• /
• v.39 no.6 s.181
• /
• pp.787-801
• /
• 2006

Focused in the characteristic of R&D on Geoscience and Mineral Resources as basic research area, we survey on methods of public works' economic impact analysis including cost-benefit analysis and resent technology evaluation methods and suggest apply-methods to conduct economic impact analysis on R&D of geoscience and mineral resources. To conduct economic impact analysis on the basic research area, it need to identification research's out-come not just output. In this perspective, we propose a method, Input-Output-Outcome Roadmapping to identify the outcome of R&D and show the relation of input, output, and outcome of R&D. Furthermore, noticing the different effects of R&D from public works, we directly evaluate the use-value of the academic theory or geological maps through Contingent Valuation Method(CVM) and others developed as evaluation methods on environmental goods. In indirect application methods, it can evaluate the partial of the pubic works' benefit with assuming R&D factors if R&D is a part of public works. If not, we evaluate the R&D's value as reductions of costs or additions of benefit with finding related public works.

• Journal of Biomedical Engineering Research
• /
• v.38 no.4
• /
• pp.183-189
• /
• 2017

Electrosurgical Unit(ESU) is medical equipment that cut or coag tissues using electrical energy. It is used in hospitals' outpatient clinic room and operating room. Improper use of an ESU may cause fatal injuries to the patient, such as burns. So, before using an ESU, make sure that it is supplying enough energy for cut and coag by measuring the output power and checking the output power cable. In this study, we developed a simple ESU power measurement system PW100 that allows anyone to check the basic output power. And PW100 can check the state of the cable associated with the output power before using ESU. Then, we compared the measured output power of the PW100 with an ESU Analyzer which was commercialized, and compared the performance. In the experiment, the output power measured by the PW100 was lower value than an ESU Analyzer's that. However, the PW100's output power measured in the 5% error range and showed stable reproducibility by a low %RSD value.

• Journal of Information Technology Services
• /
• v.17 no.1
• /
• pp.47-58
• /
• 2018

In this study, we define Fintech services as review previous literatures and identify the traditional Fintech service market for analysing the economic effects of the Fintech Industry by using the 2014 Input-Output Table. We can identify the current market of Fintech industry which consists of VAN, PG, financial SW, mobile banking and Fintech R&D and we conduct Input-Output analysis by using non-competitive import model. The Input-Output analysis results show that production inducement effect and front/rear chain effect of the Fintech Industry are below average of other industries. This is because the Fintech technology and industry were emerging in Korea at that time (2014), and thus the ripple effects are not significant. Especially, due to the existing white risk financial regulation, new business opportunities have not been open to adapt new ICT-financial technologies. Therefore, when the business ecosystem is build through deregulation and platforms of the financial sector, it is expected that the Fintech Industry will have a high ripple effect. In this study, we identify the current market of Fintech industry from ICT indusries and conduct Input-Output analysis. The economic effects of the Fintech industry are not remarkable, but it is significant to identify the emerging market and present the basic analysis of issued research field.

• The Journal of the Korea Contents Association
• /
• v.19 no.9
• /
• pp.11-25
• /
• 2019

In Korea, there is a high demand for the operation of differentiated programs in basic research considering the characteristics of academic fields. The results of this study shows that the higher the level of research competence, the higher the quality of research outputs. The results also tell us that the quality level of the research outputs is different according to the field of study. Based on the results, we propose a method to differentiate the selection rate of each discipline in the system that operates the individual basic research projects by the level of research capacity.

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.433-439
• /
• 2005

We have developed a biosensor reading system using a white light source and a color-sensor. To reduce the environmental effect, we used the ratio of specific color intensity to the entire white light intensity. Also we could improve the responsibility of the system by controlling the amplification of the color sensor output.

• Restorative Dentistry and Endodontics
• /
• v.48 no.4
• /
• pp.41.1-41.17
• /
• 2023

Objectives: This scientometric and bibliometric analysis explored scientific publications related to hydraulic calcium silicate-based (HCSB) sealers used in endodontology, aiming to describe basic bibliometric indicators and analyze current research trends. Materials and Methods: A comprehensive search was conducted in Web of Science and Scopus using specific HCSB sealer and general endodontic-related terms. Basic research parameters were collected, including publication year, authorship, countries, institutions, journals, level of evidence, study design and topic of interest, title terms, author keywords, citation counts, and density. Results: In total, 498 articles published in 136 journals were retrieved for the period 2008-2023. Brazil was the leading country, and the universities of Bologna in Italy and Sao Paolo in Brazil were represented equally as leading institutions. The most frequently occurring keywords were "calcium silicate," "root canal sealer MTA-Fillapex," and "biocompatibility," while title terms such as "calcium," "sealers," "root," "canal," "silicate based," and "endodontic" occurred most often. According to the thematic map analysis, "solubility" appeared as a basic theme of concentrated research interest, and "single-cone technique" was identified as an emerging, inadequately developed theme. The co-occurrence analysis revealed 4 major clusters centered on sealers' biological and physicochemical properties, obturation techniques, retreatability, and adhesion. Conclusions: This analysis presents bibliographic features and outlines changing trends in HCSB sealer research. The research output is dominated by basic science articles scrutinizing the biological and specific physicochemical properties of commonly used HCSB sealers. Future research needs to be guided by studies with a high level of evidence that utilize innovative, sophisticated technologies.

• Fashion & Textile Research Journal
• /
• v.14 no.2
• /
• pp.269-276
• /
• 2012

The aim of this study is to develop clothing size system according to each size interval for obese girls aged 10~12 by classifying the upper bodies. The criteria for subjects in this study were girls who had over 1.46 of the R$\ddot{o}$hrer Index. A total of 229 schoolgirls who met these criteria were enrolled. Results are as follows; 1st, 5 factors were extracted by factor analysis and 3 clusters were categorized by cluster analysis, cylinder-type, inverted triangle-type and inverted trapezoid-type. And 2nd, as a consequence of size system establishment, the basic body sizes and reference body sizes were different according to types even in commonly-appeared size names at sections of respective types. The research findings above suggest that it is necessary to figure out the obesity types according to height and bust girth sizes representing basic sizes and to design the patterns in consideration of the characteristics of obese body shapes. And it may be used as a basic data to decide the desirable output of production according to respective body types.