• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.12
• /
• pp.1185-1192
• /
• 2012

The typical operating temperature of an automotive fuel cell is lower than that of an internal combustion engine, which necessitates a refined strategy for thermal management. In particular, the performance of the cooling module has to be higher for a fuel cell system because the temperature difference between the fuel cell and the surrounding is lower than in the case of the internal combustion engine. Even though the cooling system of an automotive fuel cell determines the operating temperature and temperature distribution of the fuel cell, it has attracted little research attention. This study presents the mathematical model of a cooling system for an automotive fuel cell system using Matlab/$Simulink^{(R)}$. In particular, a radiator model is developed for design optimization from the development stage to the operating stage for an automotive fuel cell. The cooling system model comprises a fan, pump, and radiator. The pump and fan model have an empirical relation, and the dynamics of the pump and fan are only explained by motor dynamics. The basic design study was conducted, and the geometric setup of the radiator was investigated. When the control logic was applied, the pump senses the coolant inlet temperature and the fan senses the coolant out temperature. Additionally, the cooling module is integrated with the fuel cell system model so that the performance of the cooling module can be investigated under realistic operating conditions.

• Membrane Journal
• /
• v.5 no.1
• /
• pp.35-43
• /
• 1995

For several years lots of attempts have been made to establish the liquid membrane-based techniques for separations of gas mixtures especially containing carbon dioxide. A more effective system to separate $CO_{2}$ from flue gases, a circulatory hollow-fiber membrane absorber(HFMA) consisting of absorption and desorption modules with vacuum mode, has been considered in this study. Gas-liquid mass transfer has been modeled on a membrane module with non-wetted hollow-fibers in the laminar flow regime. The influence of an absorbent flow rate on the separation performance of the circulatory HFMA can be predicted quantitatively by obtaining the $CO_{2}$ concentration profile in a tube side. The system of $CO_{2}/N_{2}$ binary gas mixture has been studied using pure water as an(inert) absorbent. As the absorbent flow rate is increased, the permeation flux(i.e., defined as permeation rate/membrane contact area) also increases. The enhanced selectivity compared to the previous results, on the other hand, shows the decreasing behavior. It has been found obviously that the permeation flux depends on the variations of pressure in gas phase of desorption module. From an accurate comparison with the results of conventional flat sheet membrane module, the advantageous permeability of this circulatory HFMA can be clearly ascertained as expected. Our efforts to the theoretical model will provide the basic analysis on the circulatory HFMA technique for a better design and process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.157-163
• /
• 2016

BIM is currently applied in some domestic construction firms, but it is not being actively utilized due to changes in working environments and qualms about new studies. In order to utilize a BIM model in the design phase, process information is needed during construction, but the input system and utilization method of the process information's state are not complete. Therefore, we propose a BIM template for construction progress management that can show basic BIM information as the construction progresses in an easy and convenient way. This method will facilitate the adoption of BIM and enhance the productivity of construction companies. To this end, we designed a progress explorer for step-by-step progress and work schedules, and we generated three-dimensional views and a progress list by applying unit information (primary units, part units, and detail units) of the work breakdown structure (WBS) to the parameters. To use the BIM template, work progress information is input to the BIM modeling objects through Dynamo. We also used Dynamo for quick and easy calculation of the quantity of materials needed for construction work. To test the BIM template, we applied it to an actual project and evaluated its visibility and a progress list. The results showed that the proposed BIM template facilitates progress management of a project and can thus facilitate the adoption of BIM and improve the productivity of construction companies.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.636-644
• /
• 2019

The purpose of this study is to explore practical intervention strategies by identifying the relationships among digital informatization capacity, level of digital informatization accessability and life satisfaction of disabled people and to determine differences among these relationships depending on perceived level of social support networks. The participants were 1,639 disabled people from the 2017 digital information gap survey and the results, based on structural equation modeling and multi-group analysis, are as follows. First, digital informatization capacity has a positive influence on the level of digital informatization accessability(β=.65), and life satisfaction(β=.08). The level of digital informatization accessability also has positive influence on life satisfaction(β=.44). Second, the analysis result of the mediated effects of digital informatization accessability level between digital informatization capacity and life satisfaction was significant at a level (β=.29) even greater than the direct effect of digital informatization capacity on life satisfaction. Third, digital information capacity and digital informatization accessability have an influence on life satisfaction regardless of their perceived level of social support. The findings suggest that creating online environments where disabled people can enjoy leisure, culture, and social interaction with high accessibility and utility are as important as providing education for improving their digital informatization capacity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.190-198
• /
• 2020

The purpose of this study was to investigate the changing trajectory of self-esteem and to explore contemporaneous and lagged effects of social supports(family, friends, and teacher) of 4th graders in elementary school to 9th graders in middle school. The subjects were 1,296 multiethnic students, who participated in the Multicultural Children and Adolescents Panel Study(MCAPS) from 2011 to 2016. The results of piecewise growth function showed that students' self-esteem was increased during upper grade in elementary school but soon deceased during middle school. Individual differences were found at initial, 1st and 2nd changing status. Students with higher level at initial status in self-esteem showed less increased pattern during elementary school but greater decreased pattern during middle school. In addition, supports from family and teacher showed contemporaneous effects across all 6 years while supports from friends showed such effects only for 5 years except 9th grade. Lagged effects of family were found in elementary school and significant lagged effects with supports from friends were found at 6th and 8th grade. The results of this study imply that the social support of family, friends, and teacher has an important role to encourage the self-esteem of multicultural adolescents.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.3
• /
• pp.161-175
• /
• 1985

The simplified method drawing the S-N curves in welding joints of the cover plates, the transverse stiffners and the gusset plates of the plate girders by calculation and its computer program without the direct fatigue tests, was established. And the method was applied to the Young- Dong Great Bridge, the 3 th Han River Bridge and the Kang Chon Bridge. Before this, SS 41, SS 50, SWS 50 and SWS 58 were selected, then the compact tension specimens were made by the use of these materials, the things welded by these materials transversely and the ones longitudinally to the crack propagation direction. The fatigue tests were performed by the use of these 'specimens, and the values of material constants c and m were obtained. By these results the followings were obtained. It was showed that the fatigue: strength in the case of the cover plates was much lower than in the case of other two cases. It was showed that, in the case of the cover plates with the cover plates thicker the fatigue strength was lower, but besides this the fatigue strength was not much influenced by the size of specimens. It was showed that in the difference from this the fatigue strength was sensitively influenced by the values of c and m. It was showed that in accordance with the lower values of c and m the fatigue strength was fairly higher, in accordance with the lower values of m the gradient of the S-N curves was abrupter. It was considered that if such data were accumulated continuously, in the near future the basic pattern used availably in providing the indicater of the fatigue design of the plate girders, and presuming the life-proof of the existing plate girders.

• Journal of Distribution Research
• /
• v.12 no.1
• /
• pp.85-104
• /
• 2007

The basic purpose of this study is to investigate service quality and relationship quality affecting the result of long-term relationship between service buyers and suppliers. This research presented a constructive model(service quality${\rightarrow}$relationship quality${\rightarrow}$customer's revisiting intention) and then propose the research model base on prior researches and studies about relationships among components of service. Data were gathered from respondents who visit traditional markets. For this study, data were analyzed by SPSS and AMOS 5.0. Data were gathered from 209 respondents in the Korean traditional market. This research proposed 6 hypotheses on 5 latent variables and tested through structural equation modeling. 5 alternative measurements were compared through statistical significance test of the paths of research model and the overall fitting level of structural equation model. and the result was successful. The results of the study indicate that service quality is properly modeled as an antecedent of relationship quality and revisiting intentions. We also discussed managerial implications of the study and its limitations.

• Journal of Distribution Research
• /
• v.17 no.3
• /
• pp.93-113
• /
• 2012

Early conflict research in channel and organization area have focused on the definition of conflict construct, its cause, consequence and identified conflict resolution management. Recent studies about conflict, however, have explored new assumption of complexity, a multidimensional conflict construct, contextual conflict management strategies, positive and negative conflict/consequence, and the conflict resolution strategy. Although many literatures exists on channel conflict resolution, little research has been done about relationship learning and performance from conflict resolution perspective. This study explores how channel members can achieve a relationship learning, as a conflict resolution mechanism, which enhance co-created value in marketing channel relationship. Therefore we propose that conflict resolution strategies(collaborating behavior and avoiding behavior) influence channel performance(effectiveness and efficiency) through relationship learning processes(learning via information exchange, joint interpretation and coordination, relationship-specific knowledge memory), in view of buyer-seller relationship. The research model is shown at

• Journal of Distribution Science
• /
• v.13 no.10
• /
• pp.135-142
• /
• 2015

Purpose - Following the speedy development of the smart phone industry, tourism companies started to increase their brand recognition and sales volume by adopting mobile applications. However, applications for tourism industries are still insignificant. This study tries to analyze empirical evidence from Korean and Chinese consumers who have used mobile tour applications. By using an expansion of the technology acceptance model (TAM), this study will find what factors have effects on user intention for mobile tour applications. The findings will be helpful for the development of mobile tour applications and the tourism industries. Research design, data, and methodology - This study uses the TAM, which was presented by Davis in 1989. This study uses consumer acceptance level, consumer choice attitude, and use intention as the basic variables to fit to the TAM, and adopts choice content quality, brand value, and usage motivation as additional variables to analyze. This study has developed several hypotheses and collected data from 620 users who used mobile applications for tourism during April 1 to April 30, 2015. A total of 612 valid questionnaires were collected and used in the data analysis. The data was analyzed with structural equation modeling using SPSS Win/pc and Amos 22.0. Results - The findings can be summarized as follows: First, the content quality affects the consumer acceptance degree and choice attitude. Second, the brand value has a directly positive effect on the consumer acceptance degree and choice attitude. It is clear that the content quality and brand value play important roles in raising consumer acceptance and choice attitude. Third, usage motivation has no effect on the consumer acceptance degree and choice attitude. Fourth, the acceptance degree does not have any effect on the consumer choice attitude. Fifth, the acceptance degree affects the use intention. Last, the consumer choice attitude affects the use intentions. This indicates that consumer acceptance and choice attitude must both be achieved to induce use intention among consumers. Finally, the effects of the mobile tour application content quality and brand value on consumer acceptance degree and choice attitude were confirmed. Additionally, the effects of the consumer acceptance degree and choice attitude on use intentions were analyzed. Conclusion - It is not meaningful for tourism marketing to launch tour applications in the mobile market without understanding tourism consumer characteristics. When developing mobile tour applications, companies should focus on the characters of consumer choice attitudes as high quality, high brand value, usefulness, and ease of mobile tour applications. This study has limitations in that it did not consider negative factors such as perceived risks or analyze whether there are differences between Korean and Chinese consumers. In the future, we will consider equipping the same mobile tour applications commonly used by both Korean and Chinese consumers, and then examine negative factors as well as the differences in mobile tour applications between Korean and Chinese consumers.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.20 no.2
• /
• pp.228-232
• /
• 2018

Process-based crop models have been used to assess the impact of climate change on crop production. These models are implemented in procedural or object oriented computer programming languages including FORTRAN, C++, Delphi, Java, which have a stiff learning curve. The requirement for a high level of computer programming is one of barriers for efforts to develop and improve crop models based on biophysical process. In this study, we attempted to develop a Chinese cabbage model using Microsoft Excel with Visual Basic for Application (VBA), which would be easy enough for most agricultural scientists to develop a simple model for crop growth simulation. Results from Soil-Plant-Atmosphere-Research (SPAR) experiments under six temperature conditions were used to determine parameters of the Chinese cabbage model. During a plant growing season in SPAR chambers, numbers of leaves, leaf areas, growth rate of plants were measured six times. Leaf photosynthesis was also measured using LI-6400 Potable Photosynthesis System. Farquhar, von Caemmerer, and Berry (FvCB) model was used to simulate a leaf-level photosynthesis process. A sun/shade model was used to scale up to canopy-level photosynthesis. An Excel add-in, which is a small VBA program to assist crop modeling, was used to implement a Chinese cabbage model under the environment of Excel organizing all of equations into a single set of crop model. The model was able to simulate hourly changes in photosynthesis, growth rate, and other physiological variables using meteorological input data. Estimates and measurements of dry weight obtained from six SPAR chambers were linearly related ($R^2=0.985$). This result indicated that the Excel/VBA can be widely used for many crop scientists to develop crop models.