• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.07a
• /
• pp.306-306
• /
• 2004

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.2
• /
• pp.39-45
• /
• 1994

Analysis and design procedure for three-line three port bandpass / bandstop fliter consisting of three line microstrip structures is reported. The measured results for experimental three port structure is shown to be in good agreement with theoretical poedictions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.544-552
• /
• 2010

In this paper, a new method to enhance the stop bandwidth of the compact microstrip bandstop filter based on split ring resonator(SRR) was proposed. To achieve wide stop bandwidth, we incorporated the SRR within the circular etched pattern of the defected ground structure(DGS). By incorporating the SRR within the circular etched pattern, a high magnetic coupling between SRR and signal line can be achieved. The high magnetic coupling enables the proposed structure to achieve a wide stop bandwidth. To verify the feasibility of the proposed structure, the proposed bandstop filter was compared with conventional bandstop filter employing SRRs which have been etched at both sides of the signal line. Simulation and experimental results show that the proposed structure provides an enhanced stop bandwidth compared with the conventional structure.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.92-98
• /
• 2010

A new wideband bandstop filter(BSF) with a sharp roll-off characteristic is introduced in a stripline structure in this paper. The BSF consists of two sections: the first is two capacitively coupled $\lambda/4$ short-circuited lines with opposite ground positions, while the second is a capacitively coupled $\lambda/4$ short-circuited line. The BSF provides three transmission zeros within the stopband and better than 22 dB rejection over the whole wireless local area network (WLAN) band from 5.15 to 5.825 GHz. The BSF, cascaded to an U.S. ultra-wideband(UWB: 3.1~10.6 GHz) band-pass filter(BPF), is simulated with HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape with a dielectric constant of 7.8. The measurement results agree well with the HFSS simulation results. The size of the UWB BPF including the BSF is $3{\times}6.3\times0.45\;mm^3$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.124-128
• /
• 2009

This raper proposes a dual-bandstop filter, which is based on a metamaterial transmission line using the composite right/left-handed (CRLH) and dual composite right/left-handed (D-CRLH) structures. The metamaterial structure is used for miniaturization and dual-bandstop operation at the TDMB frequency range (195 MHz) and DVB-T/H frequency range (670 MHz). The size of the proposed filter is $30{\times}15\;mm$, and the -10 dB bandstop fractional bandwidth is approximately 73 % and 50 % at each frequency, respectively.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.104-109
• /
• 2012

In this paper, we propose a way to improve the quality of L-band wireless communication from unfriendly influential factors lying in the neighboring RF bands. The UHF-band system has resonator components and they generate harmonics as the spurious in the L-band. Therefore, a metamaterial CRLH bandpass filter is designed for the purpose of system miniaturization and smaller insertion loss, and its spurious phenomenon is observed in the frequency domain. And its harmonics in the L-band are suppressed by a compact bandstop filter whose equivalent circuit is newly developed. The design methodology is validated by the equivalent circuit to be compared with commercial full-wave EM software simulations, where the spurious is dropped by 20dB. Also, the advantage of the proposed design is presented by the comparison where our filter is much smaller than the conventional parallel edge coupled filter by over 50%, with excellent harmonic suppression.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.2
• /
• pp.29-34
• /
• 1989

The analysis and design procedure for 5-coupled microstrip line structure for applications as a wide bandpass/bandstop filter for MIC and MMIC are presented to implement this one. The measured frequency responses for the transmission coefficient are in good agreement with the theoretical results predicted.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.4
• /
• pp.399-404
• /
• 1987

By using the principles of the three line coupled, the equivalent admittance parameters of the band-stop filter of the three line two port spurline for MIC are derived. The frequency and in/output impedance characteristics of the filter were studied. One-section spurline bandstop filter with their stopband cented near 4GHz have been fabricated and tested. The results show good agreement between the theoretical centre frequency and the experimental results.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.5
• /
• pp.114-120
• /
• 1997

A design method is newly presented for the creation of planar type filters which shapes will be nonuniform transmission line with continuously varying characteristic impedances. Those filters yield frequency characteristics of the bandstop filter in transmission, and have not nay discontinuities. The design is achieved by the control of wave propagation in view to both reflection an transmission properties on the dispersive nonuniform line within the desired frequency band. The developed algorithm is based on optimized perturbations of inherent nulls of lobes from the solution of first-order nonlinear differential equation for reflection coefficients of the nonuniform line, and an appropriate distribution of reflection coefficient which affects to filter length and bandwidth. Practical measurements for designed wideband microstrip and stop filter show very good agreement with theoretical results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.834-838
• /
• 2007

A coupled-defected ground structure(C-DGS) having closely-located DGS cells is proposed for high performance bandstop filter applications. The negative coupling of ground currents between adjacent DGS cells greatly improves the stopband characteristics. We have measured the attenuation slope of 110.8 dB/GHz and -20 dB rejection band from 3.8 GHz to 15.5 GHz. Compared to the double-plane BSF, the proposed BSF improved the sharp cutoff response 7.6 times. We expect the C-DGS be helpful to improve the performance of DGS application circuits and also to extend the possible DGS applications.