• Journal of the Korean Institute of Telematics and Electronics
• /
• v.8 no.4
• /
• pp.25-30
• /
• 1971

Fabrication and measurements of the magnetically tunable YIG band pass or stop filter at X-band are discussed. Using two YIG spheres located at the region of r-f circularly polarized magnetic field between the strip lines, the pass or stop characteristics of the filter are obtained. In the case of band stop, the output level is typically 25db lower than the input power. Contrarily for the pass band, the pass band level is 22db higher than the stop frequency region. The experimental results are in good agreement with the theoretical values of FMR. Further it is shown that the structure can be used for a directional coupler.

• Journal of electromagnetic engineering and science
• /
• v.5 no.4
• /
• pp.208-212
• /
• 2005

In this paper, we introduced a band-pass filter employed the PBG structure and the aperture on the ground together. The harmonics of band pass filter have been suppressed by employing the PBG structure and the bandwidth of it has been broadened by using the aperture on the ground. The designed PBG cells have three different sizes. The largest cells, the middle cells, and the smallest cells have suppressed the multiple of second harmonics, the multiple of third harmonics, and the multiple of fifth harmonics, respectively. The center frequency has been 2.18 GHz. The bandwidth has been increased from 230 MHz up to 310 MHz(80 MHz, about $35\%$) by the aperture and the ripple characteristics in passband have been improved and the harmonic frequencies have been suppressed about 30 dB by the PBG.

• Progress in Superconductivity
• /
• v.4 no.2
• /
• pp.132-136
• /
• 2003

Extremely selective high temperature superconducting (HTS) band -pass filters were developed for the base transceiver station applications of Digital Cellular communication Service (DCS). The filters have a bandwidth of 25 MHz at a center frequency of 834 MHz. There are 12 resonators which have spiral-meander microstrip-line structures in order to reduce far-field radiations with a reasonable tunability. As a result, the size of filters is 5 mm $\times$ 17 mm $\times$ 41 mm. Device characteristics exhibited a low insertion loss of -0.4 dB with a -0.2 dB ripple and a return loss better than -10 dB in the pass-band at 65 K. The out-of-band signals were attenuated better than 60 dB about 3.5 MHz from the lower band edge, and 3.8 MHz from the higher band edge.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.82-89
• /
• 2011

In this paper, we numerically study both band-pass and band-stop plasmonic filters based on Metal-Insulator-Metal (MIM) waveguides and circular ring resonators. The band-pass filter consists of two MIM waveguides coupled to each other by a circular ring resonator. The band-stop filter is made up of an MIM waveguide coupled laterally to a circular ring resonator. The propagating modes of Surface Plasmon Polaritons (SPPs) are studied in these structures. By substituting a portion of the ring core with air, while the outer dimensions of the ring resonator are kept constant, we illustrate the possibility of red-shift in resonant wavelengths in order to tune the resonance modes of the proposed filters. This feature is useful for integrated circuits in which we have limitations on the outer dimensions of the filter structure and it is not possible to enlarge the dimension of the ring resonator to reach to longer resonant wavelengths. The results are obtained by a 2D finite-difference time-domain (FDTD) method. The introduced structures have potential applications in plasmonic integrated circuits and can be simply fabricated.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.6
• /
• pp.37-43
• /
• 2013

In this paper, an UWB (Ultra Wide Band) band-pass filter with open stubs using SIR (Stepped Impedance Resonator) structure is presented. The proposed band pass filter (BPF) has SIR structure instead of open stubs for UWB application with low insertion loss. The bandwidth of the proposed BPF is 103 % at the center frequency of 5.8GHz and the insertion and return losses are 0.17dB and 13.1dB, respectively. Also, the entire size of the proposed band-pass filter is $21.6{\times}17.8mm^2$.

• Speech Sciences
• /
• v.10 no.2
• /
• pp.249-258
• /
• 2003

This study attempted to examine a speaker identification method using difference sum and correlation coefficient determined from a pair of intensity level matrices of band-pass-filtered numeric sounds produced by ten female speakers of similar age and height. Subjects recorded three digit numbers at a quiet room at a sampling rate of 22 kHz on a personal computer. Collected data were band-pass-filtered at five different band ranges. Then, matrices of five intensity levels at 100 proportional time points were obtained. Pearson correlation coefficients and the sum of absolute intensity differences between a pair of given matrices were determined within and across the speakers. Results showed that very high correlation coefficient and small difference sum generally occurred within each speaker but some individual variation was also observed. Thus, the matrix pair with a higher coefficient and a smaller difference sum was averaged to form each individual's model. Comparison among the speakers yielded generally low coefficients and large differences, which suggests successful speaker identification, but among them there were a few cases with very high coefficients and small differences. Future studies will focus on finer band ranges and additional spectral parameters at some peak points of the intensity contour at a low frequency band.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.219-222
• /
• 2003

In this paper, we designed a Ku-band BPF(Band Pass Filter) by microstrip line that most usually used a microwave device design and fabrication. Here a substrate of designed BPF were silicon substrate(${\varepsilon}_r=11.8$), and metal line was copper and silver/copper structure. And a configration of BPF was used hairpin pattern. A center frequency of designed BPF was 10GHz and their FBW(Fractional Band Width) was 20%(2GHz). It presented simulated results obtained for a 10GHz filter which yields an insertion loss of 0.1dB that ripple value related chebyshev reponse. Finallt we tried to make that a 30dB attenuation frequency was 20% of center frequency.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.2
• /
• pp.85-89
• /
• 2016

In this paper, we studied effects of tilting angle of band pass filter on the characteristics of fluorescence imaging system. Theoretical modeling showed that transmittance and filtering range are highly dependent on the tilting angle. Measurements on transmittance as a function of wavelength confirmed that changes in transmittance and the band filter range are in good agreement with theoretical prediction. Therefore, characteristics of band pass filter can be precisely tuned by altering tilting angle of band pass filter in order to enhance fluorescence signal in bio imaging system.

• ETRI Journal
• /
• v.27 no.5
• /
• pp.643-646
• /
• 2005

This letter proposes a band-pass filter (BPF) with two transmission zeros based on a combination of parallel coupling and end coupling of half-wave transmission lines. The fabricated BPF exhibited a narrow bandwidth and two transmission zeros near the pass-band due to the end-coupled and shielding waveguide. At the center operation frequency of 60 GHz, the 20 dB bandwidth of the BPF is 1.0 GHz, which is almost 2% of the center operation frequency, and the insertion loss is 3.12 dB. Two transmission zeros reach approximately 40 dB at 58.5 and 62.5 GHz. The simulation results almost agree with the measured results.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.7
• /
• pp.1036-1044
• /
• 1995

In this paper, a band-pass filter is implemented with the diffusion and difference processes by using the diffusion neural network model. The center frequency of this band-pass filter can be varied by iterations of the diffusion and difference operations, and the selectivity can be determined by iterations of the difference operation. We propose an efficient algorithm that can generate various band-pass filters using arbitrary diffusion and difference iterations. This algorithm needs only simple operations of diffusion and difference.