• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2002년도 종합학술발표회 논문집 Vol.12 No.1
• /
• pp.141-145
• /
• 2002

In this paper, we have implemented the reflection type band-rejection filter by employing the 3-㏈ hybrid and the frequency-selective loads. The frequency-selective loads have been achieved with the 3-pole bandpass filter terminated by a 50-ohm load. The reflection type band-rejection filter is less sensitive to unloaded Q-factor of resonator than the conventional one. Measurements and simulations on the presented band-rejection filter in this paper show the excellent performances in passband and rejection-band.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.463-469
• /
• 2016

In this paper, the use of a dual composite right/left-handed coplanar waveguide (CPW) transmission line is proposed for the design of a band rejection filter. The notch property of the filter is achieved by combining the convex signal line with the shorted concave meander line, and the equivalent circuit model is extracted from the geometry of the unit cell for organizing the band rejection property. Then the equivalent parameters of the unit cell are analyzed to identify those behaviors. And the dispersion characteristics and energy distributions are simulated. In the end, the band rejection filter is manufactured by cascading two proposed unit cells. We show that the measurement result for the resonant frequency demonstrates good agreement with the simulation result and the band rejection filter provides a rejection performance of 17.5 dB at the stopband frequency ranging from 869 MHz to 894 MHz.

• 한국전자파학회논문지
• /
• 제18권7호
• /
• pp.704-709
• /
• 2007

본 논문에서는 UWB 시스템에 적용하기 위한 CPW 대역 통과 여파기를 제안하였다. 제안된 여파기는 특성 임피던스 $50{\Omega}$을 갖는 전송 선로에 슬롯만을 형성하여 대역 통과 특성을 갖도록 구현하였다. 설계된 대역 통과 여파기는 무선 랜 주파수 대역에서의 협대역 저지 특성을 얻기 위해 CPW 접지면에 두 쌍의 반파장 슬롯 공진기를 이용한 대역 저지 여파기와 결합하였다. 제작된 대역 통과 여파기는 $15.35{\times}13.60mm$의 작은 크기로 주파수 통과 대역은 3-dB 삽입 손실을 기준으로 $2.8{\sim}9.8GHz$이며 $5.15{\sim}5.71GHz$의 협대역 저지 대역을 갖는다. 또한, 군 지연 특성은 저지대역을 제외한 통과 대역 내에서 400 psec 이하를 나타낸다.

• 한국정보전자통신기술학회논문지
• /
• 제11권3호
• /
• pp.313-318
• /
• 2018

전자빔과 상호작용하는 공동공진기를 위한 동축형 대역억제필터를 설계하고 제작하였다. 제안한 필터는 공동공진기의 기본모드에 대해 4분의 1 파장 길이의 초크를 가진다. 동축형 대역억제필터의 등가회로를 제시하고 각 부분의 ABCD 파라미터를 구하여 필터 전체의 ABCD 행렬을 구했다. ABCD 행렬로부터 산란행렬을 구하여 MATLAB으로 필터를 시뮬레이션하였다. 동축형 대역억제필터 구조를 HFSS를 이용하여 시뮬레이션을 수행하여 등가회로로 시뮬레이션이 유용함을 확인하였다. 설계한 동축형 대역억제필터는 6-1/8 플랜지를 가지는 필터를 제작하였다. 제작한 필터는 6-1/8 플랜지에서 N 형 플랜지로 변환하는 변환기를 사용하여 측정하였다. 제작된 필터의 삽입손실은 공동공진기의 기본모드에서 25 dB 이상이고 1차 고차모드에서 0.25 dB 보다 작다. 측정측정 결과는 시뮬레이션한 결과와 잘 일치하며 설계 규격을 만족한다.

• Journal of electromagnetic engineering and science
• /
• 제6권1호
• /
• pp.18-23
• /
• 2006

In this paper, we demonstrate a fully integrated X-band image rejection down converter, which was developed using InGaP/GaAs HBT MMIC technology, consists of two single-balanced mixers, a differential buffer amplifier, a differential YCO, an LO quadratue generator, a three-stage polyphase filter, and a differential intermediate frequency(IF) amplifier. The X-band image rejection downconverter yields an image rejection ratio of over 25 dB, a conversion gain of over 2.5 dB, and an output-referred 1-dB compression power$(P_{1dB,OUT})$ of - 10 dBm. This downconverter achieves broadband image rejection characteristics over a frequency range of 1.1 GHz with a current consumption of 60 mA from a 3-V supply.

• 전자공학회논문지A
• /
• 제33A권4호
• /
• pp.98-105
• /
• 1996

The design method of 85 GHz-115 GHz band single side-band filter using the principle of martin-puplett inteferometer is described. It has been designed by this method and also manufactured and tested. From the test results, not only the ratio of image singal rejection of 19 dB is obtained, but also the theoretical and experimental results of center frequency of pass-band and rejection-band show the validity of the theory. This manufactured filter was installed on 100GHz band SiS (superconductor insulator superconductor ) receiver for observing cosmic radio waves and tested. We found that this filter can be used a single side-band as well as double side-band mode. The design method which is presented in this paper can be used a single side-band filter for a heterodyne type sub-milimeter wave receiver.

• 한국전기전자재료학회논문지
• /
• 제11권11호
• /
• pp.975-983
• /
• 1998

A duplexer filter operating at 1.9 GHz band for personal communication system is designed and fabricated using $lambada$/4 TEM mode dielectric resonator. The transmitting band pass filter is designed in the type of the elliptic function band rejection filter by 3 dielectric resonators with 5 additional capacitors and 3 inductors. The receiving band pass filter is designed by 3 dielectric resonators with 5 additional capacitors which give additional series resonance. The parameters which are evaluated by design theory are practically applied to the duplexer filter construction and the simulation.

• Journal of electromagnetic engineering and science
• /
• 제11권3호
• /
• pp.186-191
• /
• 2011

This paper presents a simple and effective method for improving stopband rejection characteristics of previously studied dual-band filters. Small electric couplings were applied to the symmetrically positioned shunt resonators, which divided each transmission zero into two transmission zeros without any effect on passbands. We were able to achieve improved stopband rejection characteristics by these additional transmission zeros. For the filter application, we designed a dual-band filter with improved stopband characteristics using microstrip quasi-lumped elements. The electric couplings that control the location of transmission zeros are controlled by the distance between symmetric open stubs of the filter. The filter was fabricated with a relative dielectric constant of 3.5 and a thickness of 0.76 mm. The fabricated filter has a small size ($14.6{\times}13.2{\times}0.76$ mm) and a low insertion loss when compared with conventional filters.

• ETRI Journal
• /
• 제33권6호
• /
• pp.981-984
• /
• 2011

A novel lowpass filter with a very sharp transition band and wide stopband is proposed. The proposed filter is based on T-shaped patches which are etched in symmetrical structures and folded open stub. To obtain a wide stopband, we have used stub loaded semi-circle stepped-impedance structures. By designing the resonator with high inductance and capacitance, a very sharp transition band is achieved. The proposed filter has a 3-dB cutoff frequency at 2.37 GHz and a 40-dB rejection at 2.44 GHz. The stopband with an attenuation level better than -13.2 dB is up from 2.4 GHz to 16 GHz, and consequently we have reached the high and wide rejection in stopband with compact size. Good agreements between the simulated and the measured results are presented.

• 한국정보통신학회논문지
• /
• 제13권4호
• /
• pp.636-644
• /
• 2009

본 논문에서는 구형공진기와 SIOS를 사용하여 삽입손실이 작고, 차단특성이 아주 좁고, 광대역 특성을 갖는 마이크로스트립 대역통과필터를 연구하였다. 계단 입피던스 스터브는 일반$0.25{\lambda}$ 스터브 보다 약 30%의 길이를 줄일 수 있고, 또한 스터브의 임피던스의 크기를 변경할 수 있는 장점이 있음으로 필터의 특성 개선에 적용할 수 있다. 본 논문의 객관성을 입증하기 위해서 이중모드 구형공진기를 사용한 최적화된 광대역 대역통과 필터를 구현하였다. 전송선로 모델을 사용하여 계산한 주파수 특성 결과는 실험 값과 아주 잘 일치하였다. 구현된 필터의 주파수 특성은 $L_4$ = 1.94mm인 경우에 필터의 3dB 대역폭은 52.5%(3.267GHz)이고, 삽입 손실은 0.33dB, 30dB 차단특성은 저주파수 대역에서 221MHz, 고주파수대역에서 0.181MHz이다. 최대 차단특성은 저주파 대역에서 -54dB, 고주파 대역에서 -60dB이다.