• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.374-379
• /
• 2018

The piezocomposite transducer is widely used because it is highly efficient in transforming electric energy into mechanical energy, and its frequency range is broader than that of other types of ultrasound transducers. A general piezocomposite transducer is composed of an acoustic lens, impedance matching layers, piezoelectric materials, and backing layers. When an input voltage is applied to a piezoelectric material as an active material, it generates sound waves while vibrating. At that time, an impedance matching layer helps the sound waves to propagate forward while reducing the impedance mismatch that may occur at the interface between the active material and its front material. The impedance mismatch has a negative effect on the signal of an ultrasound transducer; thus, it is important to design a matching layer to overcome the issue. In this study, an optimized feature of a matching layer with gradient properties is studied. An objective function is defined to minimize both the average and the deviation of the reflection coefficients that are functions of the frequencies. As a result, an improvement in the signal characteristics with respect to the sensitivity and bandwidth is reported.

• Journal of KSNVE
• /
• v.7 no.3
• /
• pp.511-519
• /
• 1997

For a number of years it has been known that flexural vibration in a beam and plate can be damped by the application of layer of damping (viscoelastic) material that is in turn constrained by a backing layer or foil. In this study, a quantitative analysis of damping of the sandwich beam has been performed by using impact test. The damping is characterized by the loss factor .etha. in which the damping is normalized by imaginary part of the complex bending stiffiness of the beam. Results show that the relative thickness of the sandwich beam gives more effect on the riatural-frequencies and loss factor than the variation of width does. It is also shown that the Ross-Kerwin-Ungar equation and impact test can be effectively used to identify the damping characteristic of the sandwich beam and viscoelastic material.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1985.10a
• /
• pp.23-26
• /
• 1985

압전형 초음파 변화자의 특성을 압전체, matching layer, backing, 매질, tuning 및 구동 회로를 고려하여 해석하였다. 압전체는 KLM 모델을 이용하였고 모델변수를 실험적으로 추정하여 시뮬레이션에 대입하였다. 실험적인 RTIL(Round Trip Insertion Loss)은 면반사(plane reflection)에 대한 pulse-echo를 측정하여 계산되었으며, 이론치와 비교할 때 6-dB 주파수 대역내에서 2-dB 이하의 오차가 관찰되었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.7 no.1
• /
• pp.18-31
• /
• 1987

For the purpose of domestic production of ultrasonic transducer, experiments on material selection for backing and matching layer, and electrical impedance matching between transducer and equipment were performed. The characteristics of manufactured transducers with experimental results were analyzed and compared with foreign products. Through the evaluation of the transducers manufactured and the comparision with foreign products, it is confirmed that the transducers manufactured show the good performance characteristics and efficiency.

• The Journal of the Acoustical Society of Korea
• /
• v.4 no.3
• /
• pp.16-20
• /
• 1985

압전형 초음파 변환자의 특성을 압전체, matching layer, backing, 매질, tuning 및 구동 회로를 고려하여 해석하였다. 압전체는 KLM 모델을 이용하였고, 모델변수를 실험적으로 추정하여 시뮬레이션 에 대입하였다. 실험적인 RTIL은 면반사에 대한 pulse-echo를 측정하여 계산하였으며, 이론치와 비교할 때 20 dB 주파수 대역내에서 3 dB 이하의 오차가 관찰되었다.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.81.2-81.2
• /
• 2011

The gas diffusion layer (GDL) consists of two main parts, the GDL backing layer, called as a substrate and the micro porous layer (MPL) coated on the GDBL. In this process, carbon particles of MPL penetrates to the GDBL consequently forms MPL penetration part. In this study, the micro porous layer (MPL) penetration thickness is determined as a design parameter of the GDL which affect pore size distribution profile through the GDL inducing different mass transfer characteristics. The pore size distribution and water permeability characteristics of the GDL are investigated and the cell performance is evaluated under fully/low humidification conditions. Transient response and voltage instability are also studied. In addition, to determine the effects of MPL penetration on the degradation, the carbon corrosion stress test is conducted. The GDL that have deep MPL penetration thickness shows better performance in high current density region because of enhanced water management, however, loss of penetrated MPL parts is shown after aging and it induces worse water management characteristics.

• Korean Journal of Optics and Photonics
• /
• v.2 no.4
• /
• pp.219-226
• /
• 1991

The phase and the amplitude of the photoacoustic signal were measured as a function of chopping frequency for several kinds of widely used thin metallic plates (stainless steel 304, brass, aluminum and copper) attached to plexiglass backing. The experimental data have been analyzed systematically by parameter estimation technique based on the two-layer model developed from Rosencwaig-Gersho (R-G) theory. Using this analysis, the values of thermal diffusivity and thermal effusivity of the materials have been determined.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.4
• /
• pp.329-336
• /
• 2003

Intra-Vascular Ultra-Sound (IVUS) transducers were developed for the application to diagnose coronary diseases. The transducer consists of 32 piezoelectric elements with a front insulation layer and a polymeric acoustic backing layer on a hollow alumina tube. The optimal geometrical structure of the transducer was designed through theoretical analysis of radiation patterns of the transducer. Samples of the IVUS transducers of the diameter of 3㎜ were fabricated to illustrate the design scheme. For the piezoelectric elements, 2-2 mode piezocomposite materials were employed. Experimental performance of the transducers showed good agreement with the design results, which verified feasibility of the transducer for IVUS applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.6
• /
• pp.465-470
• /
• 2003

The chemical mechanical polishing (CMP) process has been widely used for the global planarization of multi-layer structures in semiconductor manufacturing. The CMP process can be optimized by several parameters such as equipment, consumables (pad, backing film and slurry), process variables and post-CMP cleaning. However, the COO(cost of ownership) is very high, because of high consumable cost. Especially, among the consumables, the slurry dominates more than 40 %. In this paper, we have studied the CMP characteristics of diluted silica slurry by adding of raw alumina abrasives and annealed alumina abrasives. As an experimental result, we obtained the comparable slurry characteristics compared with original silica slurry in the view-point of high removal rate and low non-uniformity. Therefore, we can reduce the cost of consumables(COC) of CMP process for ULSI applications.

• Journal of the Korean institute of surface engineering
• /
• v.41 no.6
• /
• pp.274-278
• /
• 2008

3-dimensional numerical analysis for a rectangular magnetron cathode model is done to predict cooling characteristics of high power sputtering system for ZnO deposition. It includes cooling channel design, heat transfer analysis of a target, bonding layer and backing plate. In order to model erosion profiles of a target, ion current density distribution from 3D Monte Carlo simulation is used to distribute total sputtering power to 5 discrete regions. At 3 kW of sputtering power and cooling water flow of 1 liter/min at $10^{\circ}C$, the maximum surface temperature was $45.8^{\circ}C$ for a flat new target and $156^{\circ}C$ for a target eroded by 1/3 of its thickness, respectively.