• 한국전기전자재료학회논문지
• /
• 제20권7호
• /
• pp.581-586
• /
• 2007

[ $(Ba_{0.57}Sr_{0.33}Ca_{0.10})TiO_3$ ] (BSCT) powders, prepared by sol-gel method, were mixed with organic vehicle and the BSCT thick films were fabricated by the screen printing method. The structural and dielectric properties were investigated as a function of the $Yb_2O_3$ doping contents. As a result of the TG-DTA, exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All BSCT thick films showed the typical XRD patterns of a cubic polycrystalline structure. The average thickness of all BSCT thick films was about $70{\mu}m$. The grain size of the BSCT thick film doped with 0.7 mol% $Yb_2O_3$ was approximately $6.2{\mu}m$. The Curie temperature and relative dielectric constant at room temperature decreased with increasing $Yb_2O_3$ amount. Relative dielectric constant and dielectric loss of the specimen doped with 0.1 mol% $Yb_2O_3$ were 4637 and 19 % at Curie temperature, respectively.

• 한국세라믹학회지
• /
• 제44권3호
• /
• pp.147-151
• /
• 2007

An improvement for the efficiency of the $Sr_{2}SiO_{4}:Eu$ yellow phosphor under the $450{\sim}470\;nm$ excitation range have been achieved by adding the co-doping element ($Mg^{2+}\;and\;Ba^{2+}$) in the host. White LEDs were fabricated through an integration of an blue (InGaN) chip (${\lambda}_{cm}=450\;nm$) and a blend of two phosphors ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) in a single package. The InGaN-based two phosphor blends ($Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor) LEDs showed three bands at 450 nm, 550 nm and 640 nm, respectively. The 450 nm emission band was due to a radiative recombination from an InGaN active layer. This 450 nm emission was used as an optical transition of the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor. As a consequence of a preparation of white LEDs using the $Mg^{2+},\;Ba^{2+}\;co-doped\;Sr_{2}SiO_{4}:Eu$ yellow phosphor+CaS:Eu red phosphor yellow phosphor and CaS:Eu red phosphor, the highest luminescence efficiency was obtained at the 0.03 mol $Ba^{2+}$ concentration. At this time, the white LEDs showed the CCT (5300 K), CRI (89.9) and luminous efficacy (17.34 lm/W).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.32-32
• /
• 2008

Microstructure and positive temperature coefficient of resistivity (PTCR) characteristics of $0.9BaTiO_3-0.1(Bi_{0.5}Na_{0.5})TiO_3$ [BaBiNT] ceramics doped with $Nb_2O_5$ were investigated in order to develop the Pb-free high Curie temperature ($T_c$)(>$160^{\circ}C$) PTC thermistor. The BaBiNT ceramics showed a tetragonal perovskite structure, irrespective of the added amount of $Nb_2O_5$. They also have a homogeneous microstructure. The resistivity of BaBiNT ceramics was gradually decreased by doping $Nb_2O_5$, which might be due to $Nb^{+5}$ ions substituting for $Ti^{+4}$ sites. The PTCR characteristics of BaBiNT ceramics appeared when the amount of doped $Nb_2O_5$ exceeded 0.0025mol%. Moreover, the abrupt grain growth was observed for the 0.03mol% $Nb_2O_5$added BaBiNT ceramics. It showed an especially high $T_c$ of approximately $172^{\circ}C$ and good PTCR characteristics of a high $\rho_{max}/\rho_{min}$ ratio ($2.96\times10^3$), a high resistivity temperature factor (11.40/$^{\circ}C$) along with a relatively low resistivity ($3.5\times10^4\Omega{\cdot}cm$).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.623-626
• /
• 2004

[ $Ba_{0.6}Sr_{0.4}TiO_3$ ] (BST) dielectric thin films doped by Cr were prepared using an alkoxide-based sol-gel method on the Pt/Ti/SiO2/Si substrate. Atomic force microscopy and x-ray diffraction analysis showed that increasing the Cr doping ratio causes increased grain size while the surface remains smooth and crack-free. It was also found that compared with undoped films the increase of Cr content in BST improves the dielectric constant and the leakage-current characteristics. The figure of merit reached the maximum value of 72.3 at the 5 mol % of Cr doping. This composition showed the dielectric constant of 426, the loss factor of 0.0065, tenability of 47.7%, and leakage-current density (at the electric field of 100 kV/cm) of $5.31{\times}10^{-8}A/cm^2$. The results show that the Cr-doped BST thin films are prospective candidates for applications in tunable devices.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1998-2000
• /
• 2005

The effects of the addition of nanocrystalline Y2O3 powder on the microstructure and superconducting properties have been investigated in YBCO films prepared by TFA-MOD process. Precursor solution doped with extra $Y_2O_3$ Powder was prepared by adding $Y_2O_3$ powder into a stoichiometic precursor solution with a cation ratio of Y:Ba:Cu=1:2:3. Coating solutions with and without $Y_2O_3$ doping were coated on $LaAlO_3(100)$ single crystal by a dip coating method, cacination and conversion heat treatments were performed at the controlled atmosphere containing water vapor Current carry capacity(Jc) of YBCO film was enhanced about 50% by $Y_2O_3$ doping. It is thought that the enhancement of Jc is due to the better connectivity of YBCO grains and/or the flux pinning by the presence of nanocrystalline $Y_2O_3$ Particles embedded in YBCO grains.

• 한국결정성장학회지
• /
• 제20권1호
• /
• pp.25-29
• /
• 2010

페로브스카이트 구조를 갖고 $Tm_2O_3$가 첨가된 MLCC용 $BaTiO_3$ 유전체를 제조하기 위하여 환원분위기, $1320^{\circ}C$의 온도조건에서 2시간 동안 소결하였다. 유전특성 측정과 미세구조 관찰을 통하여, $Tm_2O_3$ 첨가에 따라 $BaTiO_3$ 세라믹의 유전특성에 미치는 영향에 대해 연구하였으며 각 유전체의 상분석을 통하여 이차상 유무를 확인하였다. 1 mol%의 $Tm_2O_3$를 첨가한 유전체 시편이 유전특성이 가장 우수한 반면에 2 mol% 이상의 $Tm_2O_3$를 첨가한 시편의 유전상수는 1 mol%를 첨가한 시편에 비해 낮은 값을 보였다. 유전특성에 영향을 미치는 grain 크기 및 pyrochlore 이차상 형성은 미세구조분석과 결정구조분석에 의해 조사되었다. 또한, 이들 데이터를 대표적 희토류인 $Er_2O_3$를 첨가한 유전체 시편과 비교하였고 유전특성과 관련이 있는 pyrochlore상의 형성을 상분석으로써 확인하였으며 이 결과는 세라믹 커패시터의 유전특성이 도핑에 따른 이차상과 $BaTiO_3$ tetragonality의 변화와 관련되어있다고 판단된다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.52-52
• /
• 2008

The positive temperature coefficient of resistivity (PTCR) effect in (1-x)$BaTiO_3$ - $x(Bi_{0.5}K_{0.5})TiO_3$ doped with $Nb_2O_5$ was investigated. $(Bi_{1/2}K_{1/2})TiO_3$ (BKT) is more environment-friendly than $PbTiO_3$ in order to use in PTC thermistors. The incorporation of 1 mol% BKT to $BaTiO_3$ increased the Curie temperature (Tc) to $148^{\circ}C$. Doping of $Nb_2O_5$ to $Ba_{0.99}(Bi_{0.5}K_{0.5})_{0.01}TiO_3$ (BaBKT) ceramic has enhanced its PTCR effects. For the sample containing 0.025 mol% $Nb_2O_5$, it showed good PTCR properties; low resistivity at room temperature (${\rho}_r$) of 30 $\Omega{\cdot}cm$, a high PTCR intensity of approximately $3.3\times10^3$, implying the ratio of maximum resistivity to minimum resistivity (${\rho}_{max}/{\rho}_{min}$) in the measured temperature range, and a large resistivity temperature factor (a) of 13.7%/$^{\circ}C$ along with a high Curie temperature (Tc) of $167^{\circ}C$. In addition, the cooling rate of the samples during the sintering process had an influence on their PTCR behavior. All the samples showed the best ${\rho}_{max}/{\rho}_{min}$ ratio when they have cooled down at a rate of $600^{\circ}C$/min.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.310-313
• /
• 1989

The semiconducting bodies were prepared by doping the bariume titanate with $Sb_2O_3,Nb_2O_5$and by subsequent sintering in air. The sintered bodies were annealed between $1100^{\circ}C$ and $1250^{\circ}C$ for 30 minutes to 2 hours in air. The resistivity was measured as a function of temperature from $20^{\circ}C$ to $240^{\circ}C$. The anomalous effect in resistivity occurred all of the $Nb_2O_5$ and $Sb_2O_3$doped barium titanate specimens, which were sintered in air atmosphere, and the most effective PTC effect occurred through 1 hour of sintering time at $1350^{\circ}C$ and 30 minute of annealing time at $1200^{\circ}C$. The resistivity - temperature characteristics seem to be intimately related to oxygen adsorption at grain boundaries and also to the thickness of insulating layers formed at grain boundaries during heat treatment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.776-779
• /
• 2004

The dielectric and electrical characteristics of Ce doped (Ba0.6Sr0.4)TiO3 (BST) thin films were investigated as a function of Ce content. Both atomic force microscopy (AFM) and x-ray diffraction (XRD) analysis showed that increasing the Ce doping ratio causes the decrease in grain size while the surface remains smooth and crack-free. The dielectric properties of the Ce doped BST films were found to be strongly dependent on the Ce contents. The dielectric constant and dielectric loss of the BST films decreased with increasing Ce content. However, it was also found that, compared with undoped films, the increase of Cecontent improves the leakage-current characteristics. The improvement of the electrical properties of Ce-doped BST films may be related to the decrease in the concentration of oxygen vacancies. The figure of merit (FOM) reached the maximum value of 48.9 at the 1 mol % of Cedoping. The dielectric constant, loss factor, and tunability of the 1 mol% Ce doped Ba0.6Sr0.4TiO3 thin films were 320, 0.011, and 46.3%, respectively.

• 한국세라믹학회지
• /
• 제49권1호
• /
• pp.105-110
• /
• 2012

In this paper, a yellow phosphor $Sr_3SiO_5:Eu^{2+}$ that emits efficiently at the 450 nm excitation for warm white LED is studied. In addition, the effects of various flux $BaF_2$, $NH_4Cl$ on the emission spectra were investigated. The samples were synthesized through conventional solid state reaction under reducing atmosphere of 95% $N_2$-5% $H_2$ mixture at the high temperature. All phosphors showed a excitation band from 450 nm and broad band emission peaking at region of 580 nm. The optimal concentration of $BaF_2$ flux is 3 wt% for $Sr_3SiO_5$ with doping 0.05mol Eu phosphors fired in a reductive atmosphere. The phosphor showed highest emission peaking at 582 nm.