• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.199-206
• /
• 2011

Sell call radio buoy is mostly used for searching for the location of fishing nets. Sell call radio buoy for the detection of the code uses the band pass filter(BPF). All BPF is used by imported from Japanese companies. But, Japanese companies stopped selling buoys for searching for the location of fishing nets, and domestic manufacturing companies could not sell buoys any more. Therefore, In this paper, a new method to replace the conventional buoy code detector is proposed. The proposed methods are constructed with an analog filter division composed of BPFs and notch filters as well as a microprocessor with analog digital converters. The advantage of proposed methods is able to combine various codes, can enhance receiver sensitivity. The experimental results confirm the usefulness of the proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.54-60
• /
• 2008

In this paper, the novel method is proposed to realize the parallel coupled line band pass filter using defected ground structure(DGS) inverter. This method provides simple solution which easily resolves the limit of line width happened due to high impedance on the occasion of designing filter composed of line inverter. On the basis of the proposed method and conventional method, the band pass filters haying 13.3% fractional bandwidth were designed and implemented. The measured data of two filters show usually good agreement with each other, but on the other hand the length of proposed filter become shorten about 15mm and the width of inverter line was expanded two times or more in comparison with conventional filter.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.164-173
• /
• 2009

In this paper, two new circuit structures for European and U.S. ultra-wide band(UWB) bandpass filters(BPFs) with sharp roll-off characteristics are introduced. We show first that the ultra-wide bandpass property is obtained from a $\lambda$/4 open T resonator with a capacitively coupled $\lambda$/4 short-circuited line, which provides two attenuation poles at lower and upper cutoff frequencies. Then, two identical capacitively coupled input/output lines, which can be $\lambda$/4-length open ends or $\lambda$/2-length short ends, with the T-resonator, are adopted to suppress lower and higher frequency components outside of the pass band. There is coupling between the input and output lines providing two additional transmission zeros in the lower and upper transition bands of the filter. Since the coupling between the T-resonator with the $\lambda$/4 short-circuited line and the input/output lines limits the bandwidth of the filter to the European UWB band, both the $\lambda$/4 short-circuited line and the input/output lines are inserted between the two stacked T-resonators for the U.S. UWB band. The filter structures are simulated with ADS and HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape which has the dielectric constant of 7.8. Measurement results agree well with HFSS simulation results.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.961-966
• /
• 2003

A Multi-Layer Ceramic (MLC) chip type Band-Pass Filter (BPF) using BiNb$\_$0.975/Sb$\_$0.025/ $O_4$ LTCC (Low Temperature Co-fired Ceramics) and MLC processing is presented. The MLC chip BPF has the benefits of low cost and small size. The BPF consists of coupled stripline resonators and coupling capacitors. The BPF is designed to have an attenuation pole at below the passband for a receiver band of IMT-2000 handset. The computer-aided design technology is applied for analysis of the BPF frequency characteristics. The attenuation pole depends on the coupling between resonators and the coupling capacitance. An equivalent circuit and structure of MLC chip BPF are proposed. The frequency characteristics of the manufactured BPF is well acceptable for IMT-2000 application.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.26-31
• /
• 2005

In this paper, a small BPF(band pass filter) is designed using new probe type for wireless communication system. The dielectric resonator is used high Q ceramics for low loss characteristic. In order to provide a band pass filter which can be reduced in dimension, can be reduced in height, and can be surface-mounted. The filter was fabricated using $TE_{01{\delta}}$ mode dielectric resonator. The input/output probes are attached to coner portion of the rectangular metal cavity. Results of the manufactured filter($12{\times}12{\times}8[mm]$) show that the center frequency is 9.95358[GHz], the insertion loss is -1.9[dB], the 3[dB]_bandwidth is 14.9[MHz], and the loaf Q is 664.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1983.04a
• /
• pp.29-32
• /
• 1983

In order to design the simple and economic Band-Pass Active filter, 2nd-order BPF using OP-amplifier were studied by their experments.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1077-1086
• /
• 2015

This paper presents a general-purpose design scheme of a filter bank (FB)-based radio frequency (RF) transceiver that operates across the entire ultra-high frequency (UHF) TV band from 470 MHz to 698 MHz and complies with the TV white space (TVWS) regulatory requirements. To this end, an intermediate frequency (IF) band-pass filter (BPF) with a sharp skirt characteristic is considered as a solution for handling the incoming signals from a baseband modem. Specifically, an FB-based BPF structure with four ceramic resonator filters that effectively rejects unwanted signals is proposed to extract a desired signal in the TV band. Achievable data rates of a cognitive radio system (CRS) employing the proposed FB-based RF transceiver at the application layer are investigated in both wired and wireless environments. The service coverage of the CRS network is measured according to several modulation and coding schemes (MCSs) of the CRS. The results show that the coverage of a wireless network in a nearly open area can be extended by more than 9.3 km in the TVWS. Experimental results also confirm that the proposed FB-based RF transceiver is adequate for utilization in TVWS applications.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.1
• /
• pp.103-109
• /
• 2008

In this papaer, a new type of ${\lambda}_g/4$ short stub band pass filter and ${\lambda}_g/2$ open stub band pass filter are purposed. Both are designed using FSCS technique for harmonic suppression. The proposed filters that used FSCS technique and a broadband stop filter is integrated to band pass filter to suppress the harmonics. The BSF are also placed between stubs so that the size is larger than prevent as compared to conventional one. The propose filters have center frequency of 5.8 GHz, bandwidth of 50% and harmonics suppressin is 120% has in bandwith. The measurement results in the case of ${\lambda}_g/4$ short stub filter, insertion loss of 0.5 dB, return loss of 14 dB are achieved and in the case of ${\lambda}_g/2$ open stub filter, loss of 0.8 dB, return loss of 14.4 dB are achieved. The simulation results and the measurement results are almost the same.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.2
• /
• pp.34-39
• /
• 2007

UWB(Ultra Wide Band) system for high speed and high accurate location has been studying actively. This paper presents the design and implementation of RF transceiver for DS-CDMA(Direct Sequence-Code Division Multiple Access) UWB device. Major components of RF transceiver such as Low Noise Amplifier(LNA) and Band Pass Filter(BPF) are designed and then fabricated to meet wideband characteristics. The RF transceiver was implemented by the use of the fabricated components and commercial devices after carrying out performance simulation. Through the performance evaluation of the UWB RF transceiver with W-CDMA signal, the approach of design, implementation and evaluation of RF transceiver which is available to DS-CDMA UWB system is verified.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.621-629
• /
• 2008

This paper presents a low temperature co-fire ceramics(LTCC) Upconverter for a Ka-band OBS satellite transponder in order for size reduction which is one of the most important requirement for satellite components. A S-band low-pass filter(LPF), a K-band band-pass filter(BPF), and an upconverting MMIC mixer are embedded in the multi-layer structure of the upconverter. All spurious can be selectively rejected by employing a modified Elliptic low pass filter with a multi-pole structure for the S-band LPF. Also an improved performance of out-of-band rejection can be obtained. At the K-band BPF design a layer coupled configuration is employed. The upconverting mixer is an MMIC diode mixer with a double-balanced configuration. Conversion loss and isolation of the upconverter are 9 dB and 51 dBc, respectively. The size of the LTCC upconverter is only $8{\times}7{\times}0.6mm^3$ which is one-third for the thin-film based upconverter.