• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.135-141
• /
• 1994

In order to investigate remotely the behavior and distribution of fishes, the telesounder system which was composed of two parts with a buoy station at sea and a base station on land was manufactured trial. The buoy station at sea consists of fishfinder, transmission interface and transceiver. On the other hand, the base station on land consist of transceiver, receiving interface, trigger/signal separator and color display monitor. The system simulation for the performance of telesounder was carried out by use of echo simulator which could input echo signal into fishfinder. The received power (dBm) of transceiver at 29.4MHz decreased almost in proportion to distance between transmitter and receiver, and the electric field intensity was 12.12mV/m at 100 meters distance from transmitter. The image of color display monitor at the base station on land was very well coincident with the records of fishfinder from the buoy station located at sea. Therefore, it is concluded that the telesounder system is very useful in the analysis of the information on the behavior and the distribution of fishes detected from sea.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.7
• /
• pp.316-321
• /
• 2002

In this Paper, the channel characteristics of the medium voltage(22.9kV) power line to analysis the broadband power line communication in the frequency range up to 30MHz was measured. With the sideband electrical coupler in the operating frequency range from DC to 30MHz, we measured characteristic impedance, noise and attenuation of the medium voltage power line, and then characteristic impedance was measured at the state of unloaded medium voltage power line by Scattering parameter method of Vector Network Analyzer. As a measurement result, Channel impedance shows 100~380$\Omega$ at the less than 15MHz and 70~230$\Omega$ at the more than 15 MHz. Noise characteristics of power line shows -75dBm at 20MHz and Narrowband interference noise was from 3 MHz to 7MHz.

• Journal of the Korea Society for Simulation
• /
• v.10 no.4
• /
• pp.21-30
• /
• 2001

In this paper, EMI measurement, the STGU simulation being conducted, filter design, its characteristics, and its implementation to the PCB, and finally test results are discussed. When the low pass filter was implemented within the STGU, the power of EMI decreased more than 20dBm. Finally, when TE and MTIE, two important quality measure in synchronous reference clock, was assessed, ITU-T G813 requirement was satisfied. EMI(Electromagnetic Interface) is a measure of electomagnetic radiation from equipment in the range of 10KHz to 3GHz, and can cause unexpected reactions of electronics/electrical equipment. In this study, for safe and stable communication operation, a STGU (System Timing Generation Unit), which is a 2.5G SDH System and a major EMI source, was employed to simulate electromagnetic interface. Using Open-Site test, the power of fundamental frequency of EMI of interest and its harmonics were measured. Also, a low pass filter at cut-off frequency of 2GHz was specifically designed for this study to minimize the effect of EMI between electronic components.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.7
• /
• pp.720-725
• /
• 2010

In AGPS method, user position can be obtained even in the shadow region by improving signal sensitivity. A hybrid long integration scheme employing both coherent and non-coherent integration method is commonly used in AGPS receivers. Because coherent loss increases as residual frequency become large, residual frequency should be minimized to maximize coherent integration gain. This paper presents performance analysis of residual frequency estimator using FFT in fine-time assistance AGPS method. Considering the hardware complexity and the estimation accuracy, optimal length of FFT is proposed for GPS L1 C/A signal. Signal sensitivity for estimating the residual frequency is also analysed. By field experimental results, it is found that the residual frequency can be successfully estimated using 1 second snap-shot data when GPS signal strength is larger than -150 dBm and its RMS error is 3Hz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.415-424
• /
• 2016

This paper describes a high data rate proximity transmitter design for high resolution smartphone-mirrored display applications. A 2 Gb/s transmitter is designed with a low transmission power of -70 dBm/MHz and a wide bandwidth of nearly 3 GHz. A digital pre-correction method is employed in the transmitter to mitigate the inter-symbol interference problem. A carrier-based digital pulse shaping and a reconfigurable digital envelope generation methods are employed for robust operation by utilizing 20 phases from a 2 GHz phase-locked loop. A 6.5-9.5 GHz transmitter implemented in 65 nm CMOS achieves the maximum data rate of 2 Gb/s, consuming only 7.6 mW from a 1 V supply.

• ETRI Journal
• /
• v.35 no.4
• /
• pp.578-586
• /
• 2013

Using a sub-terahertz (sub-THz) wave generated using a photonics-based technology, a high-speed wireless link operating at up to 10 Gbps is designed and demonstrated for realization of seamless connectivity between wireless and wired networks. The sub-THz region is focused upon because of the possibility to obtain sufficient bandwidth without interference with the allocated RF bands. To verify the high-speed wireless link, such dynamic characteristics as the eye diagrams and bit error rate (BER) are measured at up to 10 Gbps for non-return-to-zero pseudorandom binary sequence $2^{31}-1$ data. From the measurement results, a receiver sensitivity of -23.5 dBm at $BER=10^{-12}$ is observed without any error corrections when the link distance between the transmitter and receiver is 3 m. Consequently, we hope that our design and experiment results will be helpful in implementing a high-speed wireless link using a sub-THz wave.

• ETRI Journal
• /
• v.42 no.4
• /
• pp.549-561
• /
• 2020

We developed a 0.1-㎛ metamorphic high electron mobility transistor and fabricated a W-band monolithic microwave integrated circuit chipset with our in-house technology to verify the performance and usability of the developed technology. The DC characteristics were a drain current density of 747 mA/mm and a maximum transconductance of 1.354 S/mm; the RF characteristics were a cutoff frequency of 210 GHz and a maximum oscillation frequency of 252 GHz. A frequency multiplier was developed to increase the frequency of the input signal. The fabricated multiplier showed high output values (more than 0 dBm) in the 94 GHz-108 GHz band and achieved excellent spurious suppression. A low-noise amplifier (LNA) with a four-stage single-ended architecture using a common-source stage was also developed. This LNA achieved a gain of 20 dB in a band between 83 GHz and 110 GHz and a noise figure lower than 3.8 dB with a frequency of 94 GHz. A W-band image-rejection mixer (IRM) with an external off-chip coupler was also designed. The IRM provided a conversion gain of 13 dB-17 dB for RF frequencies of 80 GHz-110 GHz and image-rejection ratios of 17 dB-19 dB for RF frequencies of 93 GHz-100 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.2
• /
• pp.170-175
• /
• 2016

In order to transmit baseband signals through frequency dividing devices, we studied the transfer function of the device in the term of the baseband signal distortion. From the analysis, it is shown that the magnitude of the envelope signal is related to the mixer gain and the insertion loss of the low pass filter whilst the phase is the additional function with the 1/2 of the phase delay. For the purpose of the verification of the study, we designed a dynamic frequency divider at 1,400 MHz. The operating frequency range of the device is closely related to the conversion gain of mixers and the amplitude of input signal, and becomes wide as the conversion gain of mixers increases. The designed frequency divider operates between 0.9 GHz and 3.2 GHz, for -14.5 dBm input power. The circuit shows 20 mW power dissipation at $V_{DD}=2.5V$, and the simulation result shows that an amplitude modulated signal at 1,400 MHz with the modulation index of 0.9 was successfully downconverted to 700 MHz.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.2
• /
• pp.131-134
• /
• 2011

We propose a spheroid chip that uses removable cell trapping barriers and that is capable of forming and extracting multicellular spheroids. By using a conventional well plate and flask, it is difficult to form small-sized spheroids, which resemble avascular 3D cell-cell interaction. It was difficult to extract spheroids using conventional microchips and fixed cell trapping barriers. The proposed chip, however, facilitates both formation and extraction of spheroids by using removable cell trapping barriers formed by membrane deflection. The cell trapping barriers, formed at the membrane pressure of 50 kPa, hold the cells in the trapping region at a cell inlet pressure of 145.155 Pa. After incubation for 24 h, the trapped cells form uniform spheroids. We successfully extract the spheroids at a cell inlet pressure of 5 kPa after removing the membrane pressure. The extracted spheroids have a diameter of $197.2{\pm}11.7Bm$ with a viability of $80.3{\pm}7.7%$. Using the proposed chip, uniform spheroids can be formed and these spheroids can be safely extracted for carrying out the post-processing of spheroids.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.7
• /
• pp.1429-1435
• /
• 2004

In this work, high performance broadband amplifier MMIC including all the matching and biasing components, and electrostatic discharge (ESD) protection circuit was developed for K/Ka band applications. Therefore, external biasing or matching components were not required for the operation of the MMIC. STO (SrTiO3) capacitors were employed to integrate the DC biasing components on the MMIC, and miniaturized LC parallel ESD protection circuit was integrated on MMIC, which increased ESD breakdown voltage from 10 to 300 V. A pre-matching technique and RC parallel circuit were used for the broadband design of the amplifier MMIC. The amplifier MMIC exhibited good RF performances and good stability in a wide frequency range. The chip size of the MMICs was $1.7{\pm}0.8$ mm2.