• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.322-325
• /
• 2007

Precipitation characteristics of the Fe-36Ni based high strength Invar alloy for power transmission wire was investigated in this study. High strength can be obtained in this alloy through solution hardening, precipitation hardening and strain hardening by cold working. In the present study, ingots of Fe-36Ni based Invar alloys with the contents of C, Mo and V varied. Microstructure observations by OM, SEM, and TEM were carried out to validate the simulation results. BCC phase and $FeNi_3$ phase are also expected at lower temperatures below $500^{\circ}C$. Aging treatments were carried out at temperatures ranging from 400 to $900^{\circ}C$ for time intervals from 3 min to 100hrs. Peak aging condition was obtained as $400^{\circ}C$ and 1 hr. With temperature increased, peak strength was decreased abruptly. Microstructure observation was conducted by optical microscopy, scanning electron microscopy, and transmission electron microscopy.

• 한국표면공학회지
• /
• 제36권6호
• /
• pp.455-460
• /
• 2003

Microstructural and magnetic properties of nanocrystalline Fe-46 wt%Ni and Fe-36 wt%Ni alloys were investigated. Alloys were prepared by the electrodeposition process. The electrolytes were iron sulfate/nickel chloride-based and iron chloride/nickel sulfamate-based solutions. Fe-46 wt%Ni alloy was FCC structure with grain size of 10 nm, but FCC and BCC phases were found in Fe-36 wt%Ni alloy and its grain size was smaller. Effective permeability of Fe-36 wt%Ni alloy was higher than that of Fe-46 wt%Ni alloy in the high frequency range because of large electrical resistivity and small eddy current loss resulted from grain size decrease. Up to $300^{\circ}C$ of annealing temperature, grain growth of Fe-Ni alloys slowly occured. Conversely, annealing above $450^{\circ}C$ led to a drastic grain growth. In that case, effective permeability was decreased at the temperature lower than $300^{\circ}C$ but at $300^{\circ}C$ or higher effective permeability was increased. At the high frequency of 1 MHz, electrodeposited Fe-Ni alloys had higher effective permeability with an decrease in the grain size.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.340-350
• /
• 2006

Nanostructured materials exhibit attractive mechanical properties that are often superior to the performance of their coarse-grained counterparts. However, one major drawback is their low ductility, which limits their potential applications. In this paper, different strategies to obtain both high strength and enhanced ductility in nanostructured materials are reported for Ti-base and Zr-base alloys. The first approach consists of designing an in-situ composite microstructure containing ductile bcc or hop dendrites that are homogeneously dispersed in a nanostructured matrix. The second approach is related to refining the eutectic structure of a Ti-Fe-Sn alloy. For all these materials, the microstructure, mechanical properties, deformation and fracture mechanisms will be discussed.

• 한국결정성장학회지
• /
• 제14권4호
• /
• pp.129-134
• /
• 2004

본 연구에서는 기계적 합금화(MA)에 의한 고상-기상반응에 있어서 질소원자가 V-Fe계 합금의 비정질화에 미치는 영향을 조사하였다. 유성형 볼밀을 사용하여 $V_{70}Fe_{30}$혼합분말을 질소가스 분위기 중 MA 처리하였다. 그 결과 160시간 MA 처리에 의하여 비정질상이 생성됨을 알 수 있었다. 160시간 동안 MA 처리한 ($V_{70}Fe$_{30}$)_{0.89}N_{0.11}$ 분말시료의 열분석 결과 약 $600^{\circ}C$에 비정질상의 결정화에 의한 발열 peak가 관찰되었다. 또한 bcc 결정에서 비정질상으로의 구조변화 과정을 X선 및 중성자 회절법을 통하여 조사하였으며, 특히 중성자회절에서는 V원자의 중성자에 대한 간섭성 핵산란진폭이 매우 작은 특징을 이용하였다. 그 결과, 이 합금계에서의 비정질화는 모든 결정구조에서 전형적으로 존재하는 8면체 unit가 우선적으로 붕괴되어 4면체 unit로 변환되어 가는 과정임을 알 수 있었다. 또한 중성자 회절에 의한 구조해석 결과 질소원자는 V원자로 이루어진 다면체의 중심에 위치하고 있음을 알 수 있었다.

• 한국분말재료학회지
• /
• 제10권5호
• /
• pp.305-309
• /
• 2003

We report on the formation and chemical leaching of non-equilibrium $Al_{0.6}(Fe_{75}Co_{25})$ alloy produced by rod milling. X-ray diffractometry, transmission electron microscopy, differential scanning calorimetry, scanning electron microscopy, and vibrating sample magnetometry were used to characterize the as-milled and leached specimens. After 400 h, only the $Al_{0.4}Fe_{0.6}$ peak of the body-centered cubic type was present in the XRD pattern. The entire rod milling process could be divided into three different stages of milling: agglomeration, disintegration, and homogenization. The saturation magnetization, $M_s$ decreased with increased milling time, the $M_s$ of the powders before milling was about 113.8 emu/g, the $M_s$ after milling for 400 h was about 11.55 emu/g. Leaching of the Al in KOH of the Al at room temperature from the as-milled powders did not induce any significant change in the diffraction pattern. After the leached specimen had been annealed at $600^{\circ}C$ for 1 hour, the nanoscale crystalline phases were transformed into the bcc Fe, cubic Co, and $CoFe_2O_4$ phases. On cooling the specimen from 85$0^{\circ}C$, the degree of magnetization increased slightly, then increased sharply at approximately 364.8$^{\circ}C$, indicating that the bcc $Al_{0.4}Fe_{0.6}$ phase had been transformed to the Fe and Co phases.

• 한국주조공학회지
• /
• 제30권2호
• /
• pp.76-82
• /
• 2010

Effect of reaction time and sludge formation on the thickness of die soldering reaction layer has been studied in Al-9Si-0.3Mg casting alloy. Ternary ${\alpha}_{bcc}-Al_8Fe_2Si$ and ${\alpha}_{hcp}-Al_8Fe_2Si$ intermetallic compounds formed at the interface of SKD61 tool steel by interaction diffusion of Al, Fe and Si atoms after 0.5hr and 6hr immersion time, respectively. Binary ${\eta}-Fe_2Al_5$ additionally formed at the interface of SKD61 tool steel after 10hr immersion time. Thickness of soldering reaction layer in die surface increased as immersion time increased from 0.5hr to 24hr. Sludge formation was ascertained in the samples which were immersed in the melts more than 10hr. Reaction of die soldering after sludge formation was more accelerated than that of before sludge formation due to a decrease in Fe content, followed by higher diffusion rate of Al in the melt by sludge formation.

• 한국주조공학회지
• /
• 제29권4호
• /
• pp.169-175
• /
• 2009

Effect of iron and manganese contents on die soldering reaction has been studied in Al-9wt.%Si-0.3wt.%Mg alloy. Ternary ${\alpha}_{hcp}-Al_8Fe_2Si$ and ${\alpha}_{bcc}-Al_8Fe_2Si$ intermetallic compounds formed by interaction diffusion between Al-Si-Mg system alloy melt and SKD61 die steel surface. Thickness of soldering reaction layer in die steel surface decreased as Fe and Mn contents of the melts increased : When Fe content of Al-9wt.%Si-0.3wt.%Mg melts at constant 0.5wt%Mn content was 0.15wt.%, 0.45wt.% and 0.6wt.%, thickness of soldered layer of each alloy was $64.5{\mu}m,\;57.3{\mu}m$ and $46.9{\mu}m$ respectively. For Mn content of the alloy melts at constant 0.45wt.%Fe content was 0.30wt.%, 0.50wt.% and 0.70wt.%, thickness of soldered layer of each alloy was $66.1{\mu}m,\;57.3{\mu}m$ and $48.3{\mu}m$ respectively.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.417-420
• /
• 2006

The composition and structure of dendrite phase within $Zr_{76.11}Ti_{4.20}Cu_{4.51}Ni_{3.16}Be_{1.49}Nb_{10.53}$ bulk metallic glass (BMG) were confirmed by using an EPMA, XRD and TEM, respectively. The chief elements of dendrite phase were Zr-Ti-Nb and had a BCC structure. The thermal properties of this BMG have been then subsequently investigated by using a differential scanning calorimeter (DSC). The glass transition and crystallization onset temperatures were determined as $339.7^{\circ}C$ and $375.8^{\circ}C$ for this alloy, respectively. Mechanical properties have also been examined by conducting a series of uniaxial compression tests at various temperatures within supercooled liquid region under the strain rates between $10^{-4}/s$ and $3{\times}10^{-2}/s$. The deformation behavior of BMG composite within supercooled liquid region is similar to one of Vit-1 exhibiting amorphous single phase alloy. The flow stresses of BMG composite, however, are entirely higher than those of Vit-1 because dendrite phases are interfere with moving of atoms.

• 열처리공학회지
• /
• 제31권4호
• /
• pp.165-170
• /
• 2018

W, Fe, and carbon powders were mechanical alloyed to produce $W_{35}Fe_{43}C_{22}$ ternary alloy powders containing nanocrystal W embedded within amorphous matrix. When the powder samples were heated to the primary crystallization temperature of $735^{\circ}C$, most parts of their amorphous region were fully crystallized to [W,Fe]-rich $M_6C$ carbides. Interestingly, a little portion of the carbides changes to stoichiometric line compounds ($M_{12}C$ and $W_6Fe_7$) and a solution phase (Fe-rich bcc), and remaining parts of the crystallites were amorphized again. The resulting microstructure was retained even by cyclic heating between room temperature of $1,200^{\circ}C$, and thus we found that the amorphous structure can be irreversibly formed at above glass transition temperature.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권6호
• /
• pp.715-720
• /
• 1995

기계적 합금화법에 의한 비정질화 과정을 Ni-Ta계 및 Cu-Ta계에 대하여 조사하였다. Ni-Ta합금계는 혼합엔탈피가 음이나, Cu-Ta계는 혼합엔탈피가 양인 열역학적으로 대조적인 합금계이다. 볼밀 중 발생하는 원자구조 변화를 중성자회절법을 이용하여 관찰하였다. 두 합금게에 있어서 기계적 합금화에 의한 비정질상이 생성되었다. 비정질 Cu-Ta합금의 local원자구조를 혼합엔탈피가 크게 음인 Ni-Ta계의 결과와 비교하였다. 그 결과, 대조적 특성을 가진 두 합금계임에도 불구하고 원자크기가 작은 Ni 및 Cu가 bcc Ta의 결정격자 속으로 우선적으로 침입함으로써 비정질화가 진행됨을 알 수 있었다.