• Korean Journal of Food Science and Technology
• /
• v.41 no.4
• /
• pp.399-404
• /
• 2009

The goal of this study was to improve the quality of cheonggukjang by the optimization of the inoculation methods of the Bacillus subtilis (B. subtilis) and Lactobacillus plantarum (L. plantarum) strains. In order to optimize the mixed cultivation of B. subtilis and L. plantarum, the B. subtilis strain was inoculated into steamed soybeans after cultivation of L. plantarum. Inoculation size of B. subtilis was changed to the simultaneous inoculation method in order to stimulate the growth of the L. plantarum in cheonggukjang. The viable cell count of L. plantarum increased from $2{\times}10^7$ CFU/g to $2-6{\times}10^8$ CFU/g and B. subtilis grew to $9{\times}10^8$ CFU/g. These results showed that 2 strains were successfully able to grow in the steamed soybean for good quality of cheonggukjang by optimization of the inoculation methods. The sensory evaluation indicated that a favorable aroma and overall acceptance of cheonggukjang by the optimized mixed cultivation of B. subtilis and L. plantarum, which was relatively higher than those of cheonggukjang by single strain inoculation of B. subtilis.

• The Journal of Advanced Prosthodontics
• /
• v.14 no.5
• /
• pp.315-323
• /
• 2022

PURPOSE. The purpose of this study was to investigate the effect of barium silicate filler contents on mechanical properties of resin nanoceramics (RNCs) for additive manufacturing (AM). MATERIALS AND METHODS. Additively manufactured RNC specimens were divided into 4 groups depending on the content of ceramic fillers and polymers: 0% barium silicate and 100% polymer (B0/P10, control group); 50% barium silicate and 50% polymer (B5/P5); 60% barium silicate and 40% polymer (B6/P4); 67% barium silicate and 33% polymer (B6.7/P3.3). The compressive strength (n = 15) and fracture toughness (n = 12) of the specimens were measured, and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS) analyses were performed. Independent sample Kruskal-Wallis tests were performed on the compressive strength and fracture toughness test results, and the significance of each group was analyzed at the 95% confidence interval through post-tests using the Bonferroni's method. RESULTS. B6/P4 and B6.7/P3.3 exhibited much higher yield strength than B0/P10 and B5/P5 (P < .05). Compared to the control group (B0/P10), the other three groups exhibited higher ultimate strength (P < .05). The fracture toughness of B6/P4 and B6.7/P3.3 were similar (P > .05). The content of barium silicate and fracture toughness showed a positive correlation coefficient (R = 0.582). SEM and EDS analyses revealed the presence of an oval-shaped ceramic aggregate in B6/P4 specimens, whereas the ceramic filler and polymer substrate were homogeneously mixed in B6.7/P3.3. CONCLUSION. Increasing the ceramic filler content improves the mechanical properties, but it can be accompanied by a decrease in the flowability and the homogeneity of the slurry.

• Journal of Advanced Navigation Technology
• /
• v.19 no.3
• /
• pp.182-191
• /
• 2015

The automatic dependent surveillance - broadcast (ADS-B) system which is a core system of aviation system block upgrade is designed and implemented. The ADS-B system consists of the 4 blocks and 10 units, and filtering algorithm is applied to the implemented ADS-B system. To evaluate a performance of the implemented ADS-B system, real aircraft position data is used and compared reliable radar data. The comparison results show that average position difference of 99.57 m. In addition, comparisons of aircraft position data between the implemented ADS-B system employing filtering algorithm and the conventional ADS-B system under various situations are carried out, such as aircraft turning, taking off, landing, and cruising. The comparison results show that average position difference of 8.02 m.

• Proceedings of the Korea Society of Poultry Science Conference
• /
• 2002.11a
• /
• pp.136-137
• /
• 2002

The study was conducted to examine noise levels influenced by differences of altitudes and elevation from ground level. The results of the study indicated that when the noise (102 db) was created at the upper part of a steep slope area, the noise levels measured at the altitudes of 5 and 10 m were 70 and 62.1 db (R$^2$=0.9533), respectively, and that when the noise (102 db) was created at the lower part of the area, the noise levels levels measured at the altitudes of 5 and 10 m were 74.6 and 71.8 db (R$^2$=0.8519), respectively. When noise was created on a nat area, the noise levels at 10, 20 and 50 meter-ranges were 76.2, 65.9 and 55.3 db (R2 =0.9854), respectively, in which the longer distances from the noise source reduced the noise levels than the shorter and especially the noise was tremendously reduced within 10 meter-range.

• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.2
• /
• pp.68-74
• /
• 2001

A design and implementation method for the UHF-band(800MHz) variable attenuator using the 3dB coupler is proposed. The 90 degree, 3-dB Coupler is used for the variable attenuator. The principal theory for the 3-dB coupler is introduced. The 3-dB Coupler is designed by the mathematical analysis and a computer simulation tool. A PIN diode is used for the variable resistor at UHF-band. The variable attenuator using the 3-dB coupler and the PIN diode is designed and implemented. The measured results for the variable attenuator by a network analyzer show that the insertion loss is below -l0dB, and the continuous variable attenuation range is about 10dB.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.7
• /
• pp.1255-1260
• /
• 2009

Microstrip interdigital filter is designed with the width and length of a resonator, the gap distance between resonators and the location of a tap. When designing filters, it is a benefit to design with few design parameters comparing to many design parameters. In this paper we design and implement two microstrip interdigital filters operating in the UWB(Ultra Wide-Band) frequency band, one using a fixed width of a resonator and the other using a different width of resonators. The test results of the implemented filters show that the low-band high filter with a fixed width has the insertion loss of 1.49dB, -10dB band width of 720MHz, -35.7dBattenuation at 4.8GHzand below -13dB of S11. The filter with a different width of resonators has the insertion loss of 1.6dB, -10dBbandwidth of 1.63GHz and below-8dBof S11.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.4
• /
• pp.253-261
• /
• 1994

Transformation behavior and superelastic behavior of Ti-Ni-Cu alloys with various Cu content has been investigated by means of electrical resistivity measurement, X-ray diffraction, tensile test and transmission electron microscopy. Two types of heat treatment are given to the specimens: i) Solutions treatment. ii) thermo-mechanical treatment. The transformation sequence in solution treated Ti-Ni-Cu Alloys substituted by Cu for Ni up to 5at.% occurs to $B2{\rightleftarrows}B19^{\prime}$ and it proceeds in two stages by addition of 10at.%Cu, i. e, $B2{\rightleftarrows}B19{\rightleftarrows}B19^{\prime}$. Also, it has been found that Ti-30Ni-20Cu alloy transformed in one stage : $B2{\rightleftarrows}B19$. The thermo-mechanically treated Ti-47Ni-3Cu alloy transformed in two stages: B2${\rightleftarrows}$rhomboheral phase${\rightleftarrows}B19^{\prime}$, while transformation sequence in Ti-45Ni-5Cu and Ti-40Ni-10Cu alloy transformed as same as solution treated specimens. The critical stress for inducing slip deformation in solution treated and thermo-mechanically treated Ti-40Ni-10Cu alloy is about 90MPa and 320Mpa respectively.

• Journal of Navigation and Port Research
• /
• v.28 no.10 s.96
• /
• pp.851-859
• /
• 2004

This paper describes a new method for the acquisition of deviation coefficients, B and C, using a single observed deviation at a fixed compass heading. At first it discusses some problems in the synthesis of two coefficients, B and C, from various observed deviation values in the four USS warships. Then, new theories and procedures for optimal coefficients, $\^{B}\;and\;\^{C},$ are dealt with and then the validity of the proposed method are evaluated. The result of findings indicates that the approximated coefficients, $\^{B}\;and\;\^{C},$ can give optimal approximation to an single observed deviation.

• Phonetics and Speech Sciences
• /
• v.7 no.1
• /
• pp.21-26
• /
• 2015

The aim of this study is to synthesize pathological breathy voice and to make a cepstral peak prominence (CPP) table following breathiness ranks by cepstral analysis to supplement reliability of the perceptual auditory judgment task. KlattGrid synthesizer included in Praat was used. Synthesis parameters consist of two groups, i.e., constants and variables. Constant parameters are pitch, amplitude, flutter, open phase, oral formant and bandwidth. Variable parameters are breathiness (BR), aspiration amplitude (AH), and spectral tilt (TL). Five hundred sixty samples of synthetic breathy vowel /a/ for male were created. Three raters participated in ranking of the breathiness. 217 were proved to be inadequate samples from perceptual judgment and cepstral analysis. Finally, 343 samples were selected. These CPP values and other related parameters from cepstral analysis are classified under four breathiness ranks (B0~B3). The mean and standard deviation of CPP is $16.10{\pm}1.15$ dB(B0), $13.68{\pm}1.34$ dB(B1), $10.97{\pm}1.41$ dB(B2), and $3.03{\pm}4.07$ dB(B3). The value of CPP decreases toward the severe group of breathiness because there is a lot of noise and a small quantity of harmonics.

• Journal of the Korean Chemical Society
• /
• v.47 no.6
• /
• pp.591-596
• /
• 2003

Aminothienopyridazines 1a, b and aminothienocoumarin 2 condensed with DMFDMA to yield amidines 3a, b and 4. These compounds reacted with N-phenylmaleimide to yield 9 and 10. On the other hand reacting 3a, b, 4, 18, 19 and 20 with maleic anhydride afforded only the formylated derivatives 5a, b, 6, 21, 22 and 23 respectively. The reaction of 3a, b with diethyl fumarate afforded 11, formed most likely via hydrolysis of the amidine 14 during working up the reaction mixture. Irradiation of N-phenylmaleimide in microwave oven afforded [2+2] and [2+2+2] cycloaddition product.