• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.839-842
• /
• 2004

We present a fast-switching electro-optical device based on flexoelectro-optic effect in short pitch cholesterics oriented in uniform lying helix texture. The device has two operating modes: amplitude and phase modulation mode. The amplitude modulation mode is a fast in-plane switching of the device optic axis that enables to achieve a high percent of modulation of the transmitted light intensity whereas the phase mode gives a continuous change of the refractive index and thus of the phase shift of the transmitted light. By using a small concentration of diacrylate monomer and selecting the illumination conditions we have been able to create a inhomogeneous polymeric network mostly localized at both substrate surfaces and stabilize the two switching modes.

• Journal of Power Electronics
• /
• 제14권6호
• /
• pp.1208-1216
• /
• 2014

Mismatch between switching frequency and circuit parameters often occurs in industrial applications, which would lead to instability phenomena. The bifurcation behavior of $V^2$ controlled buck converter is investigated as the pulse width modulation period is varied. Nonlinear behavior is analyzed based on the monodromy matrix of the system. We observed that the stable period-1 orbit was first transformed to the period-2 bifurcation, which subsequently changed to chaos. The mechanism of the series of period-2 bifurcations shows that the characteristic eigenvalue of the monodromy matrix passes through the unit circle along the negative real axis. Resonant parametric perturbation technique has been applied to prevent the onset of instability. Meanwhile, the extended stability region of the converter is obtained. Simulation and experimental prototypes are built, and the corresponding results verify the theoretical analysis.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.49-50
• /
• 2006

We have developed vertical alignment liquid crystal display (VA-LCD), of which the viewing angle can be controlled. The VA-LCD has the function of switching between the wide viewing mode and narrow viewing angle mode using one homogeneous aligned (HA) LC layer and one compensation film with a negative C-plate. The retardation of the HA layer at off axis can be controlled by applying an electric field while keeping the retardation value to be zero at normal direction. Consequently, the device exhibits a viewing mode over $170^{\circ}$ in terms of CR = 10 in wide viewing mode and about $60^{\circ}$ in terms of CR = 2 in narrow viewing angle mode m horizontal direction.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.1312-1315
• /
• 1990

Nanometer positioning control with high velocity and long stroke is discussed. A one-axis stage mechanism driven by an AC linear motor and guided by a rolling ball guide has been constructed. Coarse and fine position controls are designed by using nonlinear dynamics of the rolling guide. Switching from coarse positioning to fine positioning is studied.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권4호
• /
• pp.405-411
• /
• 2012

This paper deals with direct torque control of an induction motor (IM) with constant switching frequency. The desired torque is obtained from the speed controller which is designed using the IP controller. Decoupling control of torque and flux is developed based on the energy model of IM using the IP controller strategies. The desired d-axis and q-axis stator voltage components are obtained from the designed controller, which decouples torque and flux. The constant switching frequency can be applied using space-vector pulse width modulation, since the desired stator voltage can be known from the decoupling torque and flux controllers. In order to achieve stable operation of the proposed IP controllers, the gains of the controllers are chosen by setting the poles in negative (left) half of s-plane and by choosing the rising time for the response of the step function. The proposed controller was verified in simulations using Matlab/Simulink and results have proven excellent performance. It was found that the proposed IP controllers can provide excellent performance to track the desired torque and speed and to reject the disturbance of load.

• International Journal of Aeronautical and Space Sciences
• /
• 제4권1호
• /
• pp.75-87
• /
• 2003

The primary objective of this study is to demonstrate ground-based experiment for the attitude control of spacecraft. A two-axis rotational simulator with a flexible ann is constructed with on-off air thrusters as actuators. The simulator is also equipped with payload pointing capability by simultaneous thruster and DC servo motor actuation. The azimuth angle is controlled by on-off thruster command while the payload elevation angle is controlled by a servo-motor. A thruster modulation technique PWM(Pulse Width Modulation) employing a time-optimal switching function plus integral error control is proposed. An optical camera is used for the purpose of pointing as well as on-board rate sensor calibration. Attitude control performance based upon the new closed-loop control law is demonstrated by ground experiment. The modified switching function turns out to be effective with improved pointing performance under external disturbance. The rate sensor calibration technique by Kalman Filter algorithm led to reduction of attitude error caused by the bias in the rate sensor output.

• 한국인터넷방송통신학회논문지
• /
• 제21권6호
• /
• pp.135-140
• /
• 2021

본 논문은 3축 가속도센서를 이용한 사고를 방지하기위한 시스템 설계에 관한 연구이다. 전원 공급단에 스위칭 파워 FET를 구성하였고, 전원 공급장치는 DC-DC, 레귤레이터, LDO를 설계하였다. 전원 문제를 한번에 해결하기 위해 2원화를 하였으며, 3축 가속도 센서를 설계하여 움직임 정보를 추출하여 안전하게 사고를 예방할 수 있도록 설계하였다. 마이크로프로세서는 I2C, UART 통신 포트를 통해 통신할 수 있도록 하였으며, J-LINK를 통해 디버깅 할 수 있도록 하였다. 가속도 센서 데이터 측정결과 30° 이상의 각도의 움직임을 감지했을 때 정상적으로 사고 방지를 위해 전원이 차단되는 것을 확인 할 수 있었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.869-874
• /
• 2004

The inverse kinematics of five-axis milling machines produce large errors near stationary points of the required surface. When the tool travels cross or around the point the rotation angles may jump considerably leading to unexpected deviations from the prescribed trajectories. We propose three new algorithms to repair the trajectories by adjusting the rotation angles in such a way that the kinematics error is minimized. Given the tool orientations and the inverse kinematics of the machine, we first eliminate the jumping angles exceeding ${\pi}$ by using the angle adjustment algorithm, leaving the jumps less than ${\pi}$ to be further optimized. Next, we propose to apply an angle switching algorithm to compute the rotations and identify an optimized sequence of rotations by the shortest path scheme. Further error reduction is accomplished by the angle insertion algorithm based an o special interpolation to obtain the required rotations near the singularity. We have verified the algorithms by five-axis milling machines, namely, MAHO600E at the CIM Lab of Asian Institute of Technology and HERMLE UWF902H at the CIM Lab of Kasetsart University.

• 제어로봇시스템학회논문지
• /
• 제11권2호
• /
• pp.103-108
• /
• 2005

Loading/Unloading task in the real industry is performed by crane, but most of the loading/unloading task with the weight of 5kg∼30kg is done by human workers and this kind of work causes industrial disaster of workers. Therefore it is necessary to develop low cost loading/unloading manipulator system to prevent this kind of industrial accidents. This paper is concerned with the design and fabrication of 2 axis pneumatic manipulators using on/off solenoid valves and accurate position control without respect to the external load and low damping in the pneumatic rotary actuator. To overcome the change of external load, switching of control parameter using LVQNN (Learning Vector Quantization Neural Network) is newly applied, which estimates the external loads in the pneumatic cylinder. As an underlying controller, a state feedback controller using position, velocity and acceleration is applied to the switching control system. The effectiveness of the proposed control algorithms are demonstrated through experiments of pneumatic cylinder with various loads.

• 유공압시스템학회논문집
• /
• 제8권2호
• /
• pp.29-35
• /
• 2011

These days the injection molding work and press work are in the trend of needing the precision control of position and pressure in a high speed. On the other hand the digital computer technology is developing rapidly. And recently the digital servo controller using micro controller become to be used more broadly, because of the merit of digital communication. In this study the sequential control of hydraulic system switching from position to pressure and to position is tried using the HACD(Hydraulic Axis Controller Digital for electrohydraulic drives) which is manufactured by BoschRexroth. Through this, the possibility of the precision sequential control using the digital servo controller HACD is examined.