• 한국가스학회지
• /
• 제18권5호
• /
• pp.47-51
• /
• 2014

이 논문은 자동차 흡배기 장치, 발전기 튜닝 및 배기 측 인화성 물질 유입에 관련된 화재에 대한 사례를 분석하고 연구하는 것이다. 첫 번째 사례는, 흡기와 배기 장치의 튜닝한 상태에서 자동차의 시동을 켜 놓고 정차된 상태에서 가연성 스티로폼이 자동차 하체로 유입되고, 배기 열에 의해 불이 붙었고, 이 열원에 누설된 연료가 화재를 확대시킨 것으로 확인되었다. 두 번째 사례는 실내의 오디오 시스템을 튜닝하고 필요한 전기의 양을 증대하기 위해 발전기 용량을 높임으로써 발전기와 연결된 배선이 과열되어 화재가 발생된 것으로 확인되었다. 세 번째 사례의 원인은 정비사가 오일을 교환한 다음 플라스틱 용기로 된 깔때기를 엔진 내부에 둔 것이 엔진의 배기열에 의해 화재가 발생된 것으로 확인되었다. 따라서, 엔진의 흡배기 시스템과 발전기 시스템을 개조하지 않도록 하여야 하며, 자동차를 수리할 때나 점검할 때 배기측에 이물질이 유입되어 화재가 발생하지 않도록 자동차의 관리에 세심한 주의를 하여야 한다.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.82-88
• /
• 2001

The EGR is needed fur one of various strategies to reduce NOx emission. But to get the proper EGR rate, the intake and exhaust system become complicated. That is a reason why we consider using the internal EGR system. The internal EGR is a system which reduces NOx by controling the residual gas fraction in cylinder by changing valve timing and valve lift of intake and exhaust. In this paper, characteristics of volumetric efficiency and residual gas fraction in cylinder were investigated for various engine speeds by changing valve timing and valve lift of intake and exhaust in the 4 stroke-cycle diesel engine. Volumetric efficiency and residual gas fraction were calculated by the method of characteristics. As the results, residual gas fraction and volumetric efficiency in cylinder by variable valve timing were visualized.

• 한국자동차공학회논문집
• /
• 제2권2호
• /
• pp.117-123
• /
• 1994

This paper describes the effect of air assisted fuel injection system(AAI) using compressed air to improve the performance of lean combustion engine. AAI is designed to promote fuel atomization and intake flow. In order to investigate the performance of engine with AAl, experiments are conducted varying the engine revolution speed, lean air-fuel ratio and intake manifold pressure. Compared with the original engine, the performance of the engine with MI is improved as the air-fuel mixture becomes leaner or the engine load becomes lower. The descreasing rate of BSFC is propotional to the relative air-fuel ratio and the lean misfire limit extended more than 0.2 relative airfuel ratio.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.232-242
• /
• 1996

In this study, the simulation program for the prediction of volumetric efficiency of the internal combustion engine by the resonator has been developed, when the resonator is mounted on the intake system of 4-cycle SI engines for the improvement of volumetric efficiency. The experimental work has also been carried out for the verification of the program, and it is found that the result of calculation by the simulation program fits qualitatively well with that of experiment. To get the optimal mounting position of resonator on the intake system, the influence of the variation of dimensions of resonator such as neck length, volume and neck diameter were examined by the numerical calculation of the program in advance and the results were compared with the experiments. It is found that the position which is departed 150cm from plenum chamber is better than any other positions, and the average amount of the increase of volumetric efficiency is about 2∼3%

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.77-83
• /
• 2005

Application of an electric heater is one of attractive methods for active regeneration in DPF systems, but its application has been limited by the capacity of electric power available in vehicles. This study was focused on intake throttling to reduce electrical energy required in the electrical heated DPF system. As results, this study showed the decrease of $30\~50\%$ of intake air mass flow rate and the increase of $20\~60^{\circ}C$ of exhaust gas temperature by the proper control of intake throttling. These intake throttling effects was helpful for regenerable temperature achievement.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1016-1019
• /
• 2004

The study of the noise reduction of an automobile has been concentrated on the reduction of the automotive engine noise because the engine noise is the major cause of automotive noise. However, many studies of automotive engine noise led to the interest of the noise reduction of the exhaust and intake system. The method of the reduction of the induction noise can be classified by the method of passive control and the method of active control. However, the passive control method has a demerit to reduce the effect of noise reduction at low frequency (below 500Hz) range and to be limited by a space of the engine room. Whereas, the active control method can overcome the demerit of passive control method. The algorithm of active control is mostly used the LMS (Least-Mean-Square) algorithm because the LMS algorithm can easily obtain the complex transfer function in real-time. Especially, Filtered-X LMS (FXLMS) algorithm is applied to an ANC system. However, the convergence performance of LMS algorithm goes bad when the FXLMS algorithm is applied to an active control of the induction noise under rapidly accelerated driving conditions. So, in order to this problem, the modified FXLMS algorithm using Moving Bandpass Filter was proposed. In this study, MBPF was implemented and use ANC for automotive intake under revived rapidly accelerated driving conditions and it was verified its performance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.460-465
• /
• 1997

In the begining stage of development of a new automobile, decision of appropriate positions and room of resonators is important to NVH engineers. To find optimized positions of resonators of an automotive intake system, numerical approach such as acoustic FEM or BEM and experimental work are possible. However, either method requires many efforts and time to prepare a numerical or a real model. This research demonstrates easy way to design an adequate intake system.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.59-72
• /
• 1998

This experimental study was carried out to investigate the characteristics of the in-cylinder eccentricity swirl flow generated by a 4 valve cylinder head with a tangential and a helical intake port. the measurements of the in-cylinder velocity field have been made by a two-channel LDA system. The mean flow coefficient(Cf(meam)), swirl ratio(Rs) and mass flowrate with valve eccentricity ratios and an intake port partition between the two intake ports were measured in the steady flow test fig using the ISM(impulse swirl meter). The experimental results indicated that the mass flowrate through the tangential intake port was 19% and 7.7% more than that of the helical intake port in case of with and without intake port partition respectively. There was a tendency to be a single rotation flow in swirl flow fields formed by a 4 valve cylinder head because of the interaction between the two intake ports. As the intake port partition was not set between flow coefficient(Cf(mean)) was 7.35%.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.175-182
• /
• 1997

The purpose of this study is to investigate the effects of intake manifold shapes to improve the engine performance in a 3-cylinder LPG engine with a closed loop fuel supply system. To know the flow resistance of intake manifolds with shape, the intake negative pressure of each runner in intake manifolds were measured by using the digital pressure meter at each driving condition. And, the engine torque and power have been measured with an engine dynamometer while adjusting the optimal fuel consumption ratio with a solenoid driver. As 속 results form this experiment, the torque characteris- tics were more improved with the plenum chamber(B type intake manifold) than with the banana type(A type intake manifold). The torque characteristics were improved at mid-engine speed(rpm) range as the inner diameter of the intake manifold became smaller. And also the optimum volume among the examined plenum chamber volume was 0.74 times(590cc) the displacement of the test engine.

• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.218-228
• /
• 1996

The behaviors of the mixture at the downstream of throttle valve in a TBI type gasoline engine plays a greater role in design of intake system. A good mixture has been influencing directly not only on the engine power but also on the pollutant emission. The mixture flow in an intake manifold is very complex, and the flow characteristics are varied with the valve type, valve angle, inlet air flow rate, and the other flow factors. Three kinds of valve are chosen in this study, and the informations of the mixture flow are observed experimentally using a PIV apparatus. Perforate valve has a smaller recirculation zone than the case of solid valve with a lower valve loss coefficient, and iti is verified that the perforated valve is also suitable to control the flow rate in a mixture flow system.