• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.8
• /
• pp.939-944
• /
• 2014

Traffic accidents caused by the attention dispersion are increasing and the behavior of the attention dispersion affects the front-observing rate, road keeping ability, and reaction time for a dangerous situation. Many drivers listen to a radio broadcast and they have to change the frequency for continuously listening a radio broadcast of the specific broadcasting station in case of crossing a boundary of the particular area. In this situation, the possibility of a car accident increases, because the attention dispersion of a driver might be occurred. Especially, the risk of a car accident caused by changing the frequency of a radio is more serious in the highway, due to the high speed of a vehicle. In order to reduce the risk of a car accident caused by handling a radio during driving car, in this paper, we propose an automatic frequency conversion algorithm for vehicle radio, which saves normal system frequencies of primary broadcasting stations in a database and determines new frequency of the changed area using the location information obtained from a navigation system in a boundary of the specific area. After determining new frequency, the proposed algorithm selects a frequency with better receiving rate comparing signal-to-noise ratios (SNRs) of two signals corresponding previous and new frequencies.

• Journal of electromagnetic engineering and science
• /
• v.1 no.2
• /
• pp.131-138
• /
• 2001

The DTV (Digital TV) tuner for an 8-VSB (Vestigial Side-Band) modulation was developed to meet the requirements of the ATSC (Advanced Television Systems Committee). The double frequency conversion and the active tracking filter in the front-end were used to cancel interferences between adjacent channels and multi-channels by suppressing the IF beat and the Image frequency. However, It was impossible to get frequency mapping between the tracking filter and the first VCO (Voltage Controlled Oscillator) in the existing DTV tuner structure which differs from the NTSC (National Television Systems Committee) tuner. This paper, therefore, suggests an assailable structure and a new method for the automatic frequency selection by mapping the frequency characteristics over the tracking voltage and the combined HW which is composed of a Micro-controller, an EEPROM (Electrically Erasable Programmable Read Only Memory), a DAC (Digital-to-Analog Converter), an OP amplifier, and a switch driver.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1161-1168
• /
• 2016

Battery energy storage system(BESS) attract the attention of the power system operators with its fast response to a disturbance in spite of its limited energy capacity. This paper proposes the operating method of BESS for following the Automatic Generation Control(AGC) frequency control which is centrally distributed by a system operator. As BESS needs to just meet the control requirement from the system operator, it should be able to properly manage the state of charge(SOC) of BESS to be available to control signal. For doing these, the proposed method distributes the control requirement to available batteries in proportion to its SOC. In addition, unavailable batteries are controlled to recover the SOC to an appropriate range, and the recovering power is supplied by available batteries meeting the control requirement. Moreover, the proposed method manages the efficiency of power conversion system (PCS) by limiting the number of PCS to be assigned for the low control requirement. Finally, the case studies are carried out to verify the effectiveness of proposed strategy.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.613-623
• /
• 2000

Digital TV tuner for 8-VSB modulation was developed with satisfying the requirements of ATSC. The double frequency conversion and the active tracking filter in the front-end were used to reduce interference of the adjacent channels and multi-channels, which suppress If beat and image band. However, it was impossible to get frequency mapping between tracking filter and first VCO(Voltage Controlled Oscillator) in the double conversion digital TV tuner differing from conventional NTSC tuner. This paper, therefore, suggests the available structure and a new method for automatic frequency selection by obtaining the mapping of frequency characteristic over tracking voltage and the combined hardware which compose of Micro-controller, EEPROM, D/A(Digital-to-Analog Converter), OP amp and switch driver to solve above problems.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.51-58
• /
• 2020

In this study, a novel method for sweeping automatic linearization of wavelength swept laser is proposed. Through the test performed on the implemented laser, the linear sweeping is held up well with a 97% decrease in nonlinearity, and 60 nm sweeping range, 1 kHz sweeping frequency, and 8.8 mW average optical power were obtained. The proposed method uses fiber Bragg grating array, optical-electronic conversion circuit, FPGA embedded module, and a LabVIEW program to generate new compensated wave patterns which were applied to the fiber Fabry-Perot tunable filter. Linear sweeping can reduce the cumbersome and time-consuming recalibration process required for nonlinear sweeping. Additionally, the proposed method provides more accurate measurement results for the structure safety monitoring system.

• Journal of Sensor Science and Technology
• /
• v.29 no.6
• /
• pp.412-419
• /
• 2020

In this study, a PID control method for sweeping automatic linearization of a wavelength swept laser is proposed. First, the closedloop transfer function embodying the PID control is derived. Through the simulation of the function, K_p = 0.022, K_i = 0.008, K_d = 0.002 were obtained as the best PID coefficients for fast linear sweeping. The performance test using the PID coefficients showed that linear sweeping was held up well with a 98.7% decrement in nonlinearity after the 10th feedback, and 45 nm sweeping range, 1 kHz sweeping frequency, and 8.8 mW average optical power were obtained. The equipment consists of a fiber Bragg grating array, an optical-electronic conversion circuit, and a LabVIEW FPGA program. Every 5s, automatic feedback and PID control generate a new compensated waveform and produce a better linear sweeping than before. Compared with nonlinear sweeping, linear sweeping can reduce the cumbersome and time-consuming recalibration processes and produce more accurate measurement results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.1
• /
• pp.51-57
• /
• 1998

This paper proposed a novel SIT high frequency resonant inverter having drive signal phase shift control function. Phasor control type inverters using SIT can realize a power conversion on the high switching frequency with low switching loss. Especially, the high output power can be abstained by connecting the output voltage of two unit inverters In serIes. The stability of system using protection circuit for over current and the automatic follow-up control with load variation by PLL is presented. This inverter produce approximately sinusoidal waveform at a high frequency, switching frequency ranging from 180[kHz] to 220[kHz], and is applied to the 2[kW] induction heating. The operating characteristics of this inverter circuit are discussed from a theoretical point of view and compared with experimental results. results.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.101-106
• /
• 2014

This paper presents a wide dynamic range radio-frequency (RF) root-mean-square (RMS) power detector using an automatic gain control (AGC) loop. The AGC loop consists of a variable gain amplifier (VGA), RMS conversion block and gain control block. The VGA exploits dB-linear gain characteristic of the cascade VGA. The proposed circuit utilizes full-wave squaring and generates a DC voltage proportional to the RMS of an input RF signal. The proposed RMS power detector operates from 500MHz to 5GHz. The detecting input signal range is from 0 dBm to -70 dBm or more with a conversion gain of -4.53 mV/dBm. The proposed RMS power detector is designed in a 65-nm 1.2-V CMOS process, and dissipates a power of 5 mW. The total active area is $0.0097mm^2$.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.3
• /
• pp.171-177
• /
• 2004

A new wave gauge using digital image of waves is developed and the performances are tested by wave tank experiments. This wave gauge uses frame frequency of 1/15 sec, conversion of analog images to digital images, and large capacity of hard disk. This wave gauge measures wave heights by detecting the buoy movement automatically from the image, where the buoy moves with the same phase of water surface. The comparison of automatic measurements of wave heights to the true data is reasonable. The wave gauge can be improved to measure wave heights on shallow waters near shorelines.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.599-600
• /
• 2008

This paper presents a high performance DC-DC boost converter by current-mode control method. As load current change, the converter change PWM/PFM operation automatically. current-mode DC-DC boost converter is implemented in a standard $0.35{\mu}m$ CMOS process. The peak efficiency was 94 % with a switching frequency of 1.2MHz.