• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.67-72
• /
• 2005

If the PNC is shutting down or wants to leave the WPAN, it uses the handover process to give control to another device in the piconet. However when the PNC is selected, only the device capability information is checked in the WPAN standard specification and no detail criteria is described. In this paper, the PNC selection method with considering the number and density of device to maximize the piconet data throughput in the WPAN is studied. From the numerical analysis results, the considering with the devices concentration has higher data throughput compared with the uniform distribution. For the efficient performance, the device distribution within the piconet should be considered in the PNC selection.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.06a
• /
• pp.49-54
• /
• 2006

During most of manufacturing processes of auto-body panels, the trimming line should be designed in advance prior to flanging. It is an important task to find a feasible trimming line to obtain a precise final part shape after flanging. This paper proposes a new fast method to find feasible trimming line based on one-step analysis. The basic idea of the one-step analysis is to seek for the nodal positions in the initial blank from the final part, and then the distribution of strain, stress and thickness in the final configuration can be calculated by comparing the nodal position in the initial blank sheet with the one of the final part. The one-step analysis method is able to predict the trimming line before flanging since the desired product shape after flanging can be defined from the final configuration and most of strain paths are simple during the flanging process. Finally, designers can obtain a discrete trimming line from the boundary of the developed meshes after one-step analysis and import it into CAD system in the early design stage. The proposed method has been successfully applied to two basic curve flanging processes demonstrating many advantages.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.1051-1054
• /
• 2013

Because of the limitations of traditional IPv4 address, the adoption of IPv6 has been accelerated. In IPv6 system, each host can obtain the IP address automatically using auto-configuration functionality, which is one of the features of IPv6. However, the auto-configuration functionality can allow a malicious user to get its IPv6 address and access the network without permission, the IP address management functionality becomes more important than IPv4. In this paper, we propose an IPv6 address management system based on IP agents, which protects the unauthorised users from accessing the network and redirects the web access of those users to a specific web page to induce them to access the network after installing the IP agents.

• ETRI Journal
• /
• v.38 no.5
• /
• pp.922-933
• /
• 2016

IP header compression schemes offer a valuable measure for bandwidth preservation. Such schemes have been practically implemented in infrastructure-based IP networks for point-to-point links. However, minimal research and practical implementation efforts have been conducted in the direction of an IP header compression strategy that can meet the peculiar requirements of multi-hop ad hoc wireless networks. In this paper, we present a practically implemented multi-hop IP header compression scheme using the Robust Header Compression (ROHC) protocol suite. The scheme runs on a novel identifier (ID) based networking architecture, known as an ID-based ad hoc network (IDHOCNET). IDHOCNET additionally solves a number of bottlenecks of pure IP-based ad hoc networks that have emerged owing to IP address auto-configuration service, distributed naming and name resolution, and the role of an IP address as an identifier at the application layer. The proposed scheme was tested on a multi-hop test bed. The results show that the implemented scheme has better gain and requires only O (1) ROHC contexts.

• Journal of the Korean Mathematical Society
• /
• v.45 no.5
• /
• pp.1443-1482
• /
• 2008

In this paper we define a Myller configuration in a Finsler space and use some special configurations to obtain results about Finsler subspaces. Let $F^{n}$ = (M,F) be a Finsler space, with M a real, differentiable manifold of dimension n. Using the pull back bundle $({\pi}^{*}TM,\tilde{\pi},\widetilde{TM})$ of the tangent bundle $(TM,{\pi},M)$ by the mapping $\tilde{\pi}={\pi}/TM$ and the Cartan Finsler connection of a Finsler space, we obtain an orthonormal frame of sections of ${\pi}^{*}TM$ along a regular curve in $\widetilde{TM}$ and a system of invariants, geometrically associated to the Myller configuration. The fundamental equations are written in a very simple form and we prove a fundamental theorem. Important lines in a Finsler subspace are defined like special lines in a Myller configuration, geometrically associated to the subspace: auto parallels, lines of curvature, asymptotes. Torse forming vector fields with respect to the Cartan Finsler connection are characterized by means of the invariants of the Frenet frame of a versor field along a curve, and the new notion of torse forming vector fields in the sense of Myller is introduced. The particular cases of concurrence and parallelism in the sense of Myller are completely studied, for vector fields from the distribution $T^m$ of the Myller configuration and also from the normal distribution $T^p$.

• Journal of KIISE:Information Networking
• /
• v.36 no.5
• /
• pp.405-412
• /
• 2009

Mobile ad hoc networks (MANETs) allow mobile nodes to communicate among themselves via wireless multiple hops without the help of the wired infrastructure. In the MANET, it is required not only a route setup mechanism that makes nodes not within each other's transmission range communicate but also mechanism in order for a node to auto-configure a unique address. In this paper, we propose an address auto-configuration mechanism when MANET is connected to the Internet via several Internet Gateways and all gateways advertise the same network prefix. By using the proposed mechanism, once a node configures an Internet topologically correct and globally unique IP address, then the node can utilize the configured address even though the node moves within the MANET. Through the simulations, we analyze the performance of our proposed mechanism and, from the simulation results, we show that out proposed mechanism outperforms the existing mechanism.

• KEPCO Journal on Electric Power and Energy
• /
• v.8 no.1
• /
• pp.5-7
• /
• 2022

KEPCO's plan is undergoing a trial operation to replace the open-loop section with ring main units configuration where underground distribution lines are installed, by linking the multi-way circuit breakers auto (MCA) on the power side of each pad-mounted transformer. However, ring main units application mentioned above may cause the ripple effects, when implementing the configuration without a study of protection coordination. Because ring main units with classical pre-set protection devices contribution in fault condition didn't consider yet. For the reliable ring main units operation, it is necessary to resolve several protection issues such as the protection coordination with substation side, prevention of the transformer inrush current. These issues can radically deteriorate the distribution system reliability Hence, it is essential to design proper protection coordination to reduce these types of problems. This paper presents a scheme of ring main units' configuration and MCA's settings of time-current curves to preserve the performance of protection coordination among the switchgears considering constraints, e.g. prevention of the ripple effects (on the branch section when a transformer failure occurs and the mainline when a branch line failure occurs). It was confirmed that the propagation of the failure for each interrupter segment could be minimized by applying the proposed TCC and the interrupter settings for the MCAs (branch, transformer). Further, it was verified that the undetected area of the distribution automation system (DAS) could be supplemented by having the MCA configurated ring main units operate first, instead of the internal protection equipment in the transformer such as the fuse, STP when a transformer failure occurs.

• The Transactions of the Korea Information Processing Society
• /
• v.4 no.5
• /
• pp.1182-1195
• /
• 1997

When we present some information, we can use application programs through multinedia-based authoring tools. Especially.many programers proposed to improve its intergration time and reduce programming speed and easy to use. However, multimedia based authoring tools have not all of programming methodolgies and do not supply special functions from user's request. Therefore, we have to apply effective functions through high-level programming languages.In this paper, we propose to use small appkication prograns through linking methods, So we reduce overhead from memory loading In authoring tools, we can use MCI(media control interface) call functions for playback audio files.we development ATS(Auto Transition System) for several functions-close MCI call audio files, get object status, page-to page trancition.We evidently show that an optimal configuration of presentation obtained by ATS algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.131-136
• /
• 2002

A design system of dies for hot extrusion of structural shapes such as Z's, L's, T's, U's and H's from aluminium alloys was developed in this study. The developed design system of dies is based of estimated die design rule system. The design rules for die design are obtained from the handbooks, plasticity theories and relevant references. The environment of the system is AutoCAD and AutoLISP, the graphic programming language was used for the configuration of the system. This system includes five major modules such as section shape design module, die opening number module, die opening layout module, die correction module and die bearing design module that are used to determine design variables. This system would be used to design of dies for hot extrusion from aluminum alloys and widely used in manufacturing course.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.4
• /
• pp.43-52
• /
• 1996

This paper describes interactive computer procedures for design the forming sequences in cold forging. This system is implemented on the personal computer and its environment is a commercial AutoCAD system. The programming language. AutoLISP, was used for the configuration of the system. Since the process of metal forming can be considered as a transformation of geometry, treatment of the geometry of the part is a key in process planning. To recognize the part section geometry, the section entity representation, the section coordinate-redius representation and the section primitive geometru were adopted. This system includes six major modules such as input module, forging design module, forming sequence design module, die design module, FEM verification module and output module which are used independently or in all. The sequence drawing wigh all dimensions, which includes the dimensional tolerances and the proper sequence of operations, can generate under the environment of AutoCAD. The acceptable forming sequences can be verified further, using the FE simulation.