• Journal of the Korean Ceramic Society
• /
• v.49 no.2
• /
• pp.191-196
• /
• 2012

In this study, tin phosphate glass system($SnO_2-(1-x)P_2O_5-xB_2O_3$) that occur during the melting of the metal oxide inhibition of the oxidation reaction, and to reduce oxides of high melting temperature in the following three methods were melting. The first is the general way in the atmosphere, and the second by injecting $N_2$ gas under a neutral atmosphere, and finally in the air were melted by the addition of a reducing agent Melt in the atmosphere when the oxidation of the metal oxide is inhibited by low temperatures were melting. In addition, the deposition of crystals within glassy or inhibit devitrification phenomenon is also improved over 80% transmittance. This phenomenon, when the melting of glass, many of $Sn^{4+}$ ions are reduced to the $Sn^{2+}$ was forming oxides SnO, because it acts as a modifier oxide.

• Journal of the Korean earth science society
• /
• v.39 no.5
• /
• pp.403-418
• /
• 2018

This study conducted synoptic and mesoscale analyses to understand the cause of Japan Tsukuba tornado development, which occurred at 0340 UTC 6 May 2012. Prior to the tornado occurrence, there was a circular jet stream over Japan, and the surface was moist due to overnight precipitation. The circular jet stream brought cold and dry air to the upper-level atmosphere which let strong solar radiation heat the ground with clearing of sky cover. A tornadic supercell developed in the area of potentially unstable atmosphere. Sounding data at Tateno showed a capping inversion at 900 hPa at 0000 UTC 6 May. Strong insolation in early morning hours and removal of the inversion instigated vigorous updraft with rotation due to vertical shear in the upper-level atmosphere. This caused multiple tornadoes to occur from 0220 to 0340 UTC 6 May 2012. When comparing Tateno's climatological temperature and dew-point temperature profile on the day of event, the mid-level atmosphere was moister than typical sounding in the region. This study showed that tornado development in Tsukuba was caused by a combination of (a) topography and potential vorticity anomaly, which increased vorticity over the Kanto Plain; (b) vertical shear, which produced horizontal vortex line; and c) thermal instability, which triggered supercell and tilted the vortex line in the vertical.

• Journal of the Korean Magnetics Society
• /
• v.9 no.3
• /
• pp.159-165
• /
• 1999

Structural, magnetic and magnetoresistance behavior of NiFe/Ag multilayers prepared by a magnetron sputter under an Ar and $Ar/H_2$ atmosphere was studied. It was difficult to make a uniform multilayer by using an Ar atmosphere. However, the uniform multilayers could be fabricated by using an $Ar/H_2$ atmosphere. This was thought to be due to decrease in the energy of the sputtered atom and Ar content of the film. Typical magnetoresistance behavior of the discontinuous NiFe/Ag multilayers appeared when the uniform multilayer was formed and annealed. Substrate temperature did not improve the uniformity of the multilayers. Above 20$0^{\circ}C$ of the substrate temperature, the films were almost formed into granular alloys rather than multilayers.

• Atmosphere
• /
• v.29 no.2
• /
• pp.149-164
• /
• 2019

The purpose of this study is to introduce the improvement of current operational climate prediction system of KMA and to compare previous and improved that. Whereas the previous system is based on GloSea5GA3, the improved one is built on GloSea5GC2. GloSea5GC2 is a fully coupled global climate model with an atmosphere, ocean, sea-ice and land components through the coupler OASIS. This is comprised of component configurations Global Atmosphere 6.0 (GA6.0), Global Land 6.0 (GL6.0), Global Ocean 5.0 (GO5.0) and Global Sea Ice 6.0 (GSI6.0). The compositions have improved sea-ice parameters over the previous model. The model resolution is N216L85 (~60 km in mid-latitudes) in the atmosphere and ORCA0.25L75 ($0.25^{\circ}$ on a tri-polar grid) in the ocean. In this research, the predictability of each system is evaluated using by RMSE, Correlation and MSSS, and the variables are 500 hPa geopotential height (h500), 850 hPa temperature (t850) and Sea surface temperature (SST). A predictive performance shows that GloSea5GC2 is better than GloSea5GA3. For example, the RMSE of h500 of 1-month forecast is decreased from 23.89 gpm to 22.21 gpm in East Asia. For Nino3.4 area of SST, the improvements to GloSeaGC2 result in a decrease in RMSE, which become apparent over time. It can be concluded that GloSea5GC2 has a great performance for seasonal prediction.

• Journal of Environmental Science International
• /
• v.5 no.4
• /
• pp.441-451
• /
• 1996

The surface meteorological and upper layer meteorological observation carried out to investigate influences of sea breeze effect on lower layer atmosphere at Gori nuclear power plant for 29∼30 July, 1996. According to surface meteorological data, the inflow of sea breeze was occurred 11:30 on 29 July, 10:30-on 30 July, respectively, at observation site. And the meteorological tower data showed that wind direction of sea breeze was identified as south-westerly, and wind speed of 58 m was 2 times stronger than that of 10 m. It is notworthy that surface inversion layer which built from the night time to daybreak of next day was not broken off by seab reeze's inflow for daytime, and strong inversion layer observed at 47∼243 m with moderately stable class (F) by URC. It was found that strong stable layer of potential temperature appeared at that layer, maximum relative humidity observed at the bottom of inversion layer and maximum mixing ratio observed in the low of inversion layer.

• Journal of the Korean Ceramic Society
• /
• v.19 no.1
• /
• pp.24-34
• /
• 1982

The effect of the several variables on wetting of AISIB1113 steel by molten glass was studied by Sessible-drop method. Experimental variables were temperature, firing atmospheres, Fe2O3 addition to the sealing glass and steel surface conditions. The degree of wetting in terms of contact angles between molten glass and metal tested at different test conditions was analyzed by using Young's equation. The results showed that contact angles in H2 atmosphere in the glass metal systems were high but in N2 atmosphere, were small for studied glass metal systems. Especially, when the glass drop was in contact with oxidized steel in N2 atmosphere, The best adherence with contact angle of approximately 9°was obtained. In the case of Fe2O3 addition in glass contact angles subtantially increased due to the increase of surface tension of glass. Wetting phenomena were also discussed under the basis of these experimental results.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.4
• /
• pp.338-346
• /
• 1981

Honing, lapping, polishing and superfinishing are applied for a precision machining to finish the metal surface, but these precision machining are micro-cutting by hard and micro-abrasive grains. Frictional machining is the new method to finish mirrorlike surface without using those abrasive grains. The frictional machining produces high pressure and high temperature instantly by compressing a tool material against the metal surface in sliding motion. The metal surface is given plastic deformation and plastic flow by the above mentioned frictional motion, but the surface roughness of the metal surface is influenced by physical and chemical reaction in surrounding atmosphere. Therefore, the atmosphere around the metal optimum atmosphere in the frictional machining. The part 1 of the study was performed in liquid atmospheres. Diesel oil, lubricant, grease, lard oil, bean oil and cutting fluid were used as such atmospheres. Medium carbon steel SM 50 C was used as a workpiece and ceramic tip was applied as a frictional tool. The result of the experiment showed characteristic machining conditions to generate the best surface roughness in each atmospheres.

• Journal of the Korean Ceramic Society
• /
• v.36 no.11
• /
• pp.1198-1204
• /
• 1999

The effect of sintering atmosphere on the grain sizes and phase distributions in 3Y-ZrO2 and 8Y-ZrO2 was investigated O2 and N2 were used as sintering atmospheres. In the case of 3Y-ZrO2 the sintered density was higher in N2 than in O2 while in the case of 8Y-ZrO2 contrary results were obtained. The observation can be explained by the nitrogen solubility into the zirconia lattice. That is nitrogen gas can behave as a diffusive gas contrary to the behavior in other oxides depending on the amount of Y2O3. In 3Y-ZrO2 tetragonal phase was retained at room temperature irrespective of sintering atmospheres. Grain sizes of two specimens were below 2㎛ and larger in O2 thin in N2 Under a given stress the transformability of tetragonal phase into monoclinic phase was higher in O2 than N2. The results are discussed on the basis of an effect of the grain size and non-transformable ttragonal(t') phase.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.682-691
• /
• 1997

We have investigated the guided optical properties of a Ti:LiNbO$_3$optical waveguide which was fabricated by Ti-diffusion in an air atmosphere and proposed an effective polishing method of waveguide endfaces. And the results of guided optical mode and fabrication condition were obtained as follows; \circled1 propagation loss : 0.53 dB/cm \circled2 mode size : horizontal/vertical=12.5${\mu}{\textrm}{m}$ \circled3 mode mismatch : 1.7 dB \circled4 diffusion temperature : 105$0^{\circ}C$, time : 8 hours \circled5 atmosphere : air

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.223-223
• /
• 2007

Thermal and mechanical properties were investigated in several semi-conductive materials which is composed of carbon black and polymer. EVA, EEA, and EBA is normally used for matrix polymer and normally acetylene black and furnace black is used. Isothermal thermo gravimetric analysis is done as a function of atmosphere and temperature. In nitrogen atmosphere semicon compound was slowly degradaded but in ambient condition degradaded fast. So in the cable manufacturing, atmosphere and materials are very important.