• Journal of Advanced Marine Engineering and Technology
• /
• 제9권2호
• /
• pp.143-152
• /
• 1985

In this paper, temperature distribution and thermal stress are investigated considering engine peak pressure and the time average temperature distribution in the piston under running conditions for the marine diesel engine. The induced stress are calculated by the Finite Element Method (FEM). The results obtained are summerized as follows. 1) The results calculated by the FEM present good agreement with other numerical solution in literatures. 2) It is comfirmed that the maximum compressive stresses are induced in the part of outside wall between the piston crown and the pin bush 3) In the axial direction, the hoop stresses are changed its sign at the portion of crown near the inner wall side. 4) Large gradient of temperature is shown in the piston crown near the side wall in the axial direction, in the part between the piston crown and the pin bush in radial direction. 5) In case of stress distribution of piston wall surface in the axial direction, the hoop stress is a little greater than axial stress, and the latter is greater than the radial stress.

• ETRI Journal
• /
• 제32권3호
• /
• pp.468-471
• /
• 2010

A compact square patch antenna with reconfigurable circular polarization (CP) at 2.4 GHz is proposed. Circular polarization is generated by an arc-shaped slot on the ground plane. In order to switch the CP orientation, the current flow direction of the patch is reconfigured via the PIN diodes mounted on the slot. As the slot and bias circuit are not placed on the patch side, the proposed antenna radiates a CP wave without alteration in the main beam direction. From the experimental results, the impedance and CP bandwidths of the proposed antenna have been demonstrated for up to 80 MHz and 25 MHz, respectively.

• ETRI Journal
• /
• 제13권4호
• /
• pp.52-57
• /
• 1991

We fabricated very high. speed PIN Photodiode module for the application of high speed optical receiver. OMVPE was used for the growth of InP layer on InGaAs absorption layer. The structure was the combination of mesa and planartype. Fabrication procedure was more complicated than simple mesa or simple planar type structure because we used semiinsulating InP substrate in order to reduce stray capacitance. The results at-5V were as follows : dark current was less than 1nA, capacitance was 0.55pF, and cutoff frequency was above 3GHz, and rise and fall time was about 100ps.

• Journal of Information Display
• /
• 제12권2호
• /
• pp.109-113
• /
• 2011

This paper summarizes the recent fabrication and characterizations of flexible high-speed radio frequency (RF) transistors, PIN-diode single-pole single-throw switches, as well as flexible inductors and capacitors, based on single-crystalline Si nanomembranes transferred on polyethylene terephthalate substrates. Flexible thin-film transistors (TFTs) on plastic substrates have reached RF operation speed with a record cut-off/maximum oscillation frequency ($f_T/f_{max}$) values of 3.8/12 GHz. PIN diode switches exhibit excellent ON/OFF behaviors at high RF frequencies. Flexible inductors and capacitors compatible with high-speed TFT fabrication show resonance frequencies ($f_{res}$) up to 9.1 and 13.5 GHz, respectively. Robust mechanical characteristics were also demonstrated with these high-frequency passives components.

• 한국전기전자재료학회논문지
• /
• 제33권1호
• /
• pp.50-55
• /
• 2020

Porcelain insulators have been used for a long time in 154 kV power transmission lines. They are likely to be exposed to sudden failure because of product deterioration. This study was conducted to evaluate the quality of porcelain insulators. After stresses were applied, the damaged regions of aged insulators were investigated in terms of chemical composition, material structure, and other properties. For porcelain insulators that were in service for a long time, the mechanical failure load was 126 kN, whereas the average mechanical failure load was 167.3 kN for new products. It was also determined that corrosion occurred at the metal pin part due to the penetration of moisture into the gap between the pin and the ceramic. Statistical analyses of failure were performed to identify the portion of the insulators that were broken. Cristobalite porcelain insulators fabricated without alumina additives had a high failure rate of 54% for the porcelain component. In the case of the addition of Alumina (Al₂O₃) to the porcelain insulators to improve the strength of the ceramic component, a more frequent damage rate of the cap and pin of 73.3% and 27%, respectively, was observed. This study reports on the material component of SiO₂ and the percentage of alumina added, with respect to the mechanical properties of porcelain insulators.

• 한국식품조리과학회지
• /
• 제30권3호
• /
• pp.262-270
• /
• 2014

This study was conducted in order to investigate the properties of bread making and quality improvement when wheat flour is replaced with whole waxy sorghum flour. Sorghum flour, which was prepared with two types of milling methods of pin mill and ultra fine pulverization, was used at different levels ranging from 10, 20 and 30%, respectively. The pasting properties of peak viscosity, setback viscosity and pasting temperature of the composite flour containing pin-milled sorghum flour were higher than those of ultra fine pulverized sorghum flour. The volumes of sorghum bread were lower than that of wheat bread; moreover, they gradually decreased with increasing amounts of sorghum flour, which has inferior dough properties and therefore collapses in the oven. The use of vital gluten (12% based on sorghum flour weight) and emulsifier (SSL; sodium stearoyl lactylate) increased the extensibility and resistance to the extension of the dough, thereby improving its rheological properties. Thus, the oven spring of bread containing sorghum was improved, demonstrating as loaf volume increase up to 15%. However, in the case of breads containing 30% sorghum flour, the loaf volumes were still unacceptably low. Therefore, the formula and the bread making process were further modified as follows: An increase of vital gluten ($12%{\rightarrow}18%$) and shortening ($3%{\rightarrow}6%$), a decrease of mixing time and dough fermentation temperature, and the addition of sorghum flour after gluten development during mixing. The above modifications resulted in the improvement of sorghum bread quality. Therefore, we suggest that pin-milled sorghum flour is more appropriate than ultra fine pulverized sorghum flour for making bread.

• 한국통신학회논문지
• /
• 제40권12호
• /
• pp.2503-2510
• /
• 2015

본 논문에서는 전력 정보를 측정하기 위한 단상 에너지 측정용 IC의 구현 방법을 제안한다. 제안된 전력 측정용 IC는 2개의 PGA(Programmable Gain Amplifier), 2개의 ${\sum}{\Delta}$ modulator, reference 회로, LDO(Low-dropout) regulator, 온도 센서, 필터부, 계산 엔진, 보정 제어부, 레지스터, 외부 인터페이스로 구성된다. $0.18-{\mu}m$ CMOS 공정으로 제작되었고, 32-pin QFN package로 제작되었다. 구현된 IC는 3.3V 전원을 공급받아 동작하며, 동작 클럭 주파수는 4,096 kHz이고, IC 동작시 소비 전력은 10 mW이다.

• Imaging Science in Dentistry
• /
• 제43권3호
• /
• pp.191-196
• /
• 2013

Purpose: This study assessed the accuracy of linear and angular measurements on panoramic radiographs taken at different positions in vitro. Materials and Methods: Two acrylic models were fabricated from a cast with normal occlusion. Straight and $75^{\circ}$ mesially and lingually angulated pins were placed, and standardized panoramic radiographs were taken at standard position, at an $8^{\circ}$ downward tilt of the occlusal plane compared to the standard position, at an $8^{\circ}$ upward tilt of the anterior occlusal plane, and at a $10^{\circ}$ downward tilt of the right and left sides of the model. On the radiographs, the length of the pins above (crown) and below (root) the occlusal plane, total pin length, crown-to-root ratio, and angulation of pins relative to the occlusal plane were calculated. The data were subjected to repeated measures ANOVA and LSD multiple comparisons tests. Results: Significant differences were noted between the radiographic measurements and true values in different positions on both models with linear (P<0.001) and those with angulated pins (P<0.005). No statistically significant differences were observed between the angular measurements and baselines of the natural head posture at different positions for the linear and angulated pins. Conclusion: Angular measurements on panoramic radiographs were sufficiently accurate and changes in the position of the occlusal plane equal to or less than $10^{\circ}$ had no significant effect on them. Some variations could exist in the pin positioning (head positioning), and they were tolerable while taking panoramic radiographs. Linear measurements showed the least errors in the standard position and $8^{\circ}$ upward tilt of the anterior part of the occlusal plane compared to other positions.

• 한국위성정보통신학회논문지
• /
• 제10권3호
• /
• pp.121-126
• /
• 2015

본 논문에서는 원형 편파 다이버시티를 구현하기 위하여 교차형 섭동 구조에 기반을 둔 새로운 원형 편파 재구성 마이크로스트립 안테나를 제안하였다. 제안한 안테나는 우회전 원형 편파와 좌회전 원형 편파를 동시에 구현하기 위하여 링 구조 방사체와 원형 편파의 방향을 선택하기 위한 두 개의 PIN 다이오드로 구성되었다. 방사체의 대각선 한 모서리에 슬롯 섭동과 스터브 섭동을 다이오드의 ON/OFF 상태를 조절함으로써, 제안한 안테나의 재구성 원형 편파는 잘 동작되고 또한 교차할 수 있었다. 또한 위성 통신 시스템 동작을 위하여 2.4 GHz의 S 대역에서 제안한 안테나는 이론적으로 분석하였고, 실험적으로 검증하였다. 제작된 안테나의 모의실험과 측정실험결과는 반사계수, 축비, 안테나 이득, 및 방사패턴에서 잘 일치함을 확인하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.967-972
• /
• 2004

The role of transfer films formed during sliding of polymer composites against steel counterfaces was studied in terms of the tribological behaviors of composites. Four kinds of composites were included in this study: (1) unfilled PPS, (2) PPS+2%CuO, (3) PPS+2%CuO+5% carbon fiber (CF), and (4) PPS+2%CuO+15%Kevlar. The filler material CuO was in nanoscale particulate form and the reinforcing material was in the form of short fibers. The composites were prepared by compression molding at $310^{\circ}C$ and sliding tests were run in the pin-on-disk sliding configuration. The counterface was made of tool steel hardened to 55-60 HRC and finished to a surface roughness of 0.09-0.10 ${\mu}m$ Ra. Wear tests were run for 6 hrs at the sliding speed of 1 m/s and contact pressure of 0.65 MPa. Transfer films formed on the counterfaces during sliding were investigated using AFM and SEM. The results showed that as the transfer film became smooth and uniform, wear rate decreased. PPS+2%CuO+15%Kevlar composite showed the lowest steady state wear rate in this study and its transfer film showed the smoothest and the most uniform characteristics. The examination of worn surfaces of PPS+2%CuO composite using X-ray area scanning (dot mapping) showed back-transfer of steel counterface material to the polymer pin surface. This behavior is believed to strengthen the polymer pin surface during sliding thereby contributing to the decrease in wear rate.