• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.890-893
• /
• 2002

This study is focused to predict the behavior of Al foam with closed-cell structure during the 3 point bending test and the upsetting test according to aspect ratio. We calculated characters of aluminum foams with closed-cell structure and took the simulation. The effects on the aspect ratio of the cell was investigated parametrically. The analysis was carried out on two models, First, the bending test in elasticity of the rectangular beam, and Second, the upsetting test in plasticity of the circular cylinder. In the analysis, the deformation of the beam and the cylinder was influenced by the aspect ratio of the cell. Further, We assumed that the geometry of feared aluminum cell change the stress and strain in the test.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.324-331
• /
• 2002

The characteristics of moisture ventilation in a dry room are studied numerically The behaviors of moisture ventilation are analyzed by varying the aspect ratio of the horizontal plane and for various positions of the outlets in the room. Three different ventilation efficiencies have been used to examine the effect of the longitudinal arrangement of outlets and transverse arrangement of outlets for each aspect ratio on ventilation inside the room. It is shown that the ventilation efficiency in the dry room can be improved by arranging the outlets transversely in the cases that the aspect ratio is less than three and longitudinally in the cases that it is greater than four.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.199-204
• /
• 2001

This paper showed the study on the heat transfer into space by the aspect ratio of solar concentration absorber, and the purpose of this study is to obtain the optimum aspect ratio and tilt angle. The boundary conditions of a numerical model were assumed as follows : (1) The heat source is located at the center of absorber. (2) The bottom was is opened and adiabatic. (3) The top, right and left walls are cooled wall. The parameters for the study are the tilt angles and the aspect ratio. The velocity vectors and isotherms were dense at wall side and the heat source. The mean Nusselt number had a maximum value at Ar=1:1 and $\theta=0^{\circ}$ and showed a low value as the tilt angles were increased.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권4호
• /
• pp.302-310
• /
• 2008

This paper puts forward an advanced consideration on the design of scaled multiple-gate FET (MuGFET); the aspect ratio ($R_{h/w}$) of the fin height (h) to fin width (w) of MuGFET is considered with the aid of 3-D device simulations. Since any change in the aspect ratio must consider the trade-off between drivability and short-channel effects, it is shown that optimization of the aspect ratio is essential in designing MuGFET's. It is clearly seen that the triple-gate (TG) FET is superior to the conventional FinFET from the viewpoints of drivability and short-channel effects as was to be expected. It can be concluded that the guideline of w < L/3, where L is the channel length, is essential to suppress the short-channel effects of TG-FET.

• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.47-53
• /
• 2005

Microholes with high aspect ratio are required in microstructures. Among various methods for producing the microhole, micro electrical discharge machining (MEDM) is very effective and useful process. But, it is difficult to machine the high aspect ratio holes below $100\;{\mu}m$ in diameter because machining condition becomes unstable due to bad removal of debris at deep hole. In this paper, ultrasonic vibration is applied to MEDM work fluid to make a high aspect ratio micro hole. It is shown that the vibration is effective in circulating the debris and increasing the machining rate. As a result, produced was a micro hole with $92\;{\mu}m$ entrance diameter, $81\;{\mu}m$ exit diameter and aspect ratio 23.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.84-87
• /
• 2009

This paper describes a novel method for fabricating large area metallic stamp with high aspect ratio micro intaglio features. Micro machined brass master with pillar and larger width groove patterns were electroformed to form inverse structures on the large area metallic stamp. This enabled large area metallic stamp with fine micro high aspect ratio micro intaglio features which were small width groove patterns and quadrilateral hole patterns that cannot be fabricated by direct micro machining process. Fabricated large area metallic stamp with high aspect ratio micro intaglio features was measured and analyzed.

• 동력기계공학회지
• /
• 제6권1호
• /
• pp.43-49
• /
• 2002

This paper showed the study on the heat transfer into space by the aspect ratio of solar concentration absorber, and the purpose of this study was to obtain the optimum aspect ratio and tilt angle. The boundary conditions of a numerical model are assumed as follows : (1) The heat source is located at the center of absorber. (2) The bottom wall is opened and adiabatic. (3) The top, right and left walls are cooled wall. The parameters for the study are the tilt angles and the aspect ratio. The velocity vectors and isotherms were dense at wall side and the heat source. The mean Nusselt number had a maximum value at Ar=1:1 and ${\theta}=0^{\circ}$ and showed a low value as the tilt angles were increased.

• 한국추진공학회지
• /
• 제8권1호
• /
• pp.44-53
• /
• 2004

본 논문에서는 슬릿형 분사노즐의 출구 종횡비에 따라 3차원 화학반응 유동장을 수치적 계산을 통하여 그 특성을 조사하고 연소／혼합 촉진 방법을 고찰하였다. 내부유입유동과 슬릿측면 와동들 둘 다 혼합관점에서 고려되어야 한다는 것을 보여 주었다. 연소효율은 종횡비1.0을 기준으로 작은 경우가 낮고 압력손실 역시 종횡비가 작은 경우가 적다. 모든 결과들은 유동방향으로 긴 슬릿이 연소와 압력손실에 대해 바람직함을 나타내고 있다.

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.594-603
• /
• 2002

The characteristics of moisture ventilation in a dry room were studied numerically The effect of three important parameters: position of outlets, aspect ratio($\beta$) of horizontal plane and air exchange rate(N), was analyzed by using the scales of ventilation efficiency. The ventilation performance was evaluated by varying the aspect ratio and air exchange rate in the four types of outlet position. It was shown that the ventilation performance was improved by decreasing the aspect ratio in the longitudinal arrangement of outlet. The highest ventilation performance was determined when $\beta$ was 4 in the transverse arrangement of outlet. Regardless of the aspect ratio, the ceiling arrangement of outlet played more dominant effect on the ventilation efficiency than the floor arrangement. In every type and aspect ratio, the increase of air exchange rate to improve ventilation performance was appropriate up to N=60 /h.

• Journal of Welding and Joining
• /
• 제26권6호
• /
• pp.42-47
• /
• 2008

TIG welding enables to produce high quality weldment. However it has some problems such as shallow penetration and large distortion due to low penetration aspect ratio after welding. In order to overcome those problems, there are many ongoing studies on A-TIG welding, which use active flux. In this study, the effect of arc length and shield gas on penetration aspect ratio with melt-run welding on STS 304 6t, on which active flux was spreaded, was investigated. Arc length was changed from 1mm to 3mm, and aspect ratio became higher as arc length was decreased in this range. 100% Ar gas, Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were used as shield gas in this study. When Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were applied, penetration and melting efficiency were both increased as compared with 100% Ar gas. Aspect ratio was the highest with Ar-2.5% $H_2$ mixed gas.