• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.5
• /
• pp.347-352
• /
• 2017

Reverse electrodialysis (RED), which generates electrical energy from the difference in concentration of two solutions, has been actively studied owing to its high potential and the increased interest in renewable energy resulting from the Paris Agreement on climate change. For RED commercialization, its power density needs to be maximized, and therefore various methods have been discussed. In this paper, the power density was measured using various flow shapes based on the aspect ratio, opening ratio, and number of distribution channels. We found that the power density is enhanced with a decrease in the aspect ratio and an increase in the opening ratio and number of distribution channels.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.53-56
• /
• 2008

In this investigation, results of laboratory tests on six reinforce concrete flat plate interior connections with elongated rectangular column support which has been used widely in tall residential buildings are presented. The purpose of this study is to evaluate an effect of column aspect ratio(${\beta}$c=$c_1/c_2$) on the hysteretic behavior under earthquake type loading. The aspect ratio of column section was taken as 0.33${\sim}$3($c_1/c_2$=1/3, 1/1, 3/1). Other design parameters such as flexural reinforcement ratio of slab and concrete strength was kept constant as ${\rho}$=1.0%, 1.5% and $f){ck}$=40MPa, respectively. Gravity shear load($V_g$) was applied by 30 percents of nominal vertical shear strength(0.3$V_o$) of the specimen. Experimental observations on punching failure pattern, peak lateral-load and story drift ratio at punching failure, and stiffness degradation were achieved and discussed in accordance with different column aspect ratio.

• Journal of ILASS-Korea
• /
• v.3 no.3
• /
• pp.23-32
• /
• 1998

The effect of reentrant type bowl geometry on combustion characteristics was investigated in a D.I. diesel engine. The main factor was the aspect ratio (Bowl Diameter / Bowl Depth) of bowl of combustion chamber, and the cylinder pressure, engine performance and emissions of the engine using the 4 kinds of the combustion chamber were meadured. Also, the combustion characteristics compared of the experimented and the calculated values which is used by the Hiroyasu's combustion model. The results are as follows; The effect of $d_c/H$ on ignition delay period are small. The smoke is corerelated to the heat release of the premixed and the diffusion combustion, i.g, the smoke decreased by decreasing the premixed combustion or increasing the diffusion combustion on cumulative heat release. The premixed combustion process has more effect than the diffusion combustion on smoke. The formal tendency of $d_c/H$ on engine performance has not appear.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.487-495
• /
• 2003

Bearings at the obtuse corner are subjected to much larger vertical reactions than other bearings because of the geometric shape of skew bridges. The current relevant specifications require that additional bars should be disposed at the bottom of concrete deck slabs to deal with the large vertical reaction on bearings at the obtuse corner. In this study, new methods of reducing the magnitude of the vertical reaction on bearings at the obtuse corner by the stiffness adjustment of bearings were proposed. The basic concept of proposed methods was to redistribute support reactions by reducing the vertical stiffness of bearings at the obtuse corner showing a relatively large vertical reaction. For 45 simply supported skew bridges designed according to the current relevant specifications, the redistribution effect of vertical reactions by the stiffness adjustment of bearings was investigated. Parameters such as skew angle, girder spacing, and deck aspect ratio that affect the distribution of support reactions were considered. The results of the analyses show that the magnitude of the vertical reaction on bearings at the obtuse corner can be reduced to the levels of straight bridges by replacing the existing bearings at the obtuse corner with new ones having the value of 1/10 or 1/20 of the vertical stiffness of the existing bearings. The reduction effect of the vertical reaction on bearings at the obtuse corner increases as the girder spacing decreases and it is more pronounced when the deck aspect ratio is 2.0.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.2
• /
• pp.36-42
• /
• 2016

Mass flow amplifier, which is an aerodynamic device, makes air flow increased by ejecting small amount of compressed air with $Coand{\breve{a}}$ effect. In this study, the flow characteristics of a mass flow amplifier were studied with various flow conditions and geometrical configurations. In order to improve the performance of mass flow amplifier, various values of clearance, diffuser angle and the aspect ratio of induced flow inlet to outlet were considered as design parameter. Furthermore, four different pressure conditions of compressed air were also considered. Numerical study was performed using the commercial CFD code, ANSYS CFX 14.5 with shear stress transport(SST) turbulent model. The results of pressure and velocity distributions were graphically depicted with different geometrical configurations and operating conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.186-192
• /
• 2007

In general, pulsation damper is installed in fuel rail for conventional MPI engine to decrease undesirable noise in vehicle cabin room. However, pulsation damper is so expensive that there are prevailing studies to reduce fuel pressure pulsations with integrated damping effect. This paper is one of basic studies for development of fuel rail to abate pulsations with self-damping effect. Primarily, the pressure pulsation characteristics was investigated with aspect ratio of cross section, wall thickness, and materials of fuel rail. A high aspect ratio or thin wall was found to absorb the pressure pulsations effectively. But volume effects on the fuel pressure pulsation reductions were not especially significant than cross section effects because volume increment rate is larger than pressure pulsation reduction rate. The fuel rail made of aluminum is effective for reduction of pressure pulsation than that of low-carbon steel. Pressure change period increases on the basis of same lengths of supply line and fuel rail as the volume is enlarged and/or the thickness of wall is thinned.

• Journal of the Korean Ceramic Society
• /
• v.42 no.1
• /
• pp.16-21
• /
• 2005

The effect of additive composition, using AlN and $Er_{2}O_{3}$ as sintering additives, on the mechanical properties of liquid-phase-sintered, and subsequently annealed SiC ceramics was investigated. The microstructures developed were quantitatively analyzed by image analysis. The average thickness of SiC grains increased with increasing the $Er_{2}O_{3}/(AlN + Er_{2}O_{3})$ ratio in the additives whereas the aspect ratio decreased with increasing the ratio. The mechanical properties versus $Er_{2}O_{3}/(AlN + Er_{2}O_{3})$ ratio curve had a maximum; i.e., there was a small composition range at which optimum mechanical properties were realized. The best results were obtained when the ratio ranged from 0.4 to 0.6. The flexural strength and fracture toughness of the SiC ceramics were $550\~650\;MPa$ and $5.5\~6.5$ MPa${\cdot}m^{1/2}$, respectively.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.425-430
• /
• 2001

The mechanical behavior of two rectangular plates spot-welded under bending is investigated in detail. The focus of the analysis is to evaluate the effect of thickness of reinforced plates with equivalent thickness. The results of this investigation are compared from detailed finite element analysis and experiments of the plates spot-welded for various parameters, such as aspect ratio, area ratio, and distance ratio of spot-welding points. The study is carried out using the equivalent thickness of the reinforced plates spot-welded.

• Solar Energy
• /
• v.12 no.3
• /
• pp.60-69
• /
• 1992

Heat transfer characteristics and heat storage rate for vertical cylinder packed with paraffin as a latent heat storage material were theoretically studied. Conduction and convection mechanism were applied to the solid and liquid phase, respectively, and the results were compared with that of pure conduction model. The effects of heating temperature, initial solid temperature and aspect ratio on rate of storage were also studied. In the initial stage of melting, the natural convection is nearly restricted by the friction at the wall and the phase boundary. But it is generated when about 40% of solid melts and again it shrinks by the hot liquid situated on the upper part of the cylinder. So overall melting rate is higher then that for pure conduction model. The increase in heating temperature and aspect ratio activates the natural convection, so melting rate becomes higher. And the larger the aspect ratio, the greater the difference between upper and lower size of the solid. In the initial stage of melting, the initial temperature of solid paraffin has great effect on the melting rate, but as melting proceeds its effect lessens gradually.

• Journal of the Korean Society of Industry Convergence
• /
• v.11 no.1
• /
• pp.35-40
• /
• 2008

Various characters of the concrete are greatly improved as the effect of the steel fiber. As the improvement effect of the steel fiber, the increment in flexural strength, shear strength, toughness, and impact strength are remarkable, and tenacious concrete is obtained. This paper presents model which can predict mechanical behavior of the structure according to aspect ratio and volume fraction of steel fiber. Experiments on compressive strength, elastic modulus and tensile strength were performed with self-made cylindrical specimens of variable aspect ratios. This paper presents an analytical study on the behavior of a beam specimen with steel fiber reinforced concrete(SFRC). The effect of the SFRC on the crack pattern, failure mode and the flexural behavior of the structure were investigated. The analysis model based on the nonlinear layered finite element method was successfully able to find the necessary amount of steel fibers, tensile steels and beam section which can best approximate flexural strength and ductility of a given conventionally reinforced concrete beam.