• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.8
• /
• pp.1376-1382
• /
• 2016

The discharge characteristics of inductively coupled $Ar/CH_4$ plasma were investigated by fluid simulation. The inductively coupled plasma source driven by 13.56 Mhz was prepared. Properties of $Ar/CH_4$ plasma source are investigated by fluid simulation including Navier-Stokes equations. The schematics diagram of inductively coupled plasma was designed as the two dimensional axial symmetry structure. Sixty six kinds of chemical reactions were used in plasma simulation. And the Lennard Jones parameter and the ion mobility for each ion were used in the calculations. Velocity magnitude, dynamic viscosity and kinetic viscosity were investigated by using the fluid equations. $Ar/CH_4$ plasma simulation results showed that the number of hydrocarbon radical is lowest at the vicinity of gas feeding line due to high flow velocity. When the input power density was supplied as $0.07W/cm^3$, CH radical density qualitatively follows the electron density distribution. On the other hand, central region of the chamber become deficient in CH3 radical due to high dissociation rate accompanied with high electron density.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.4
• /
• pp.49-54
• /
• 2013

In this study, we have investigated the effect of the substrate temperature and oxygen flow rate on the characteristics of IZO thin films for the OLED (organic light emitting diodes) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $O_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of oxygen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $O_2$ flow rate. The electrical resistivity of IZO film increased with increasing flow rate of $O_2$ under Ar+$O_2$. The change of electrical resistivity with increasing flow rate of $O_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The change of electrical resistivity with increasing substrate temperature was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed the average transmittance over 85% in the visible range. The current density and the luminance of OLED devices with IZO thin films deposited at room temperature in 0.1sccm $O_2$ ambient gas are the highest amongst all other films. The optical band gap energy of IZO thin films plays a major role in OLED device performance, especially the current density and luminance.

• Journal of the Semiconductor & Display Technology
• /
• v.11 no.4
• /
• pp.25-30
• /
• 2012

In this study, we have investigated the effect of the substrate temperature and oxygen flow rate on the characteristics of IZO thin films for the organic light emitting diodes (OLED) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $O_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of oxygen in argon mixing gas has been changed from 0.1sccm to 0.5sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $O_2$ flow rate. The electrical resistivity of IZO film increased with increasing flow rate of $O_2$ under $Ar+O_2$. The change of electrical resistivity with increasing flow rate of $O_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The change of electrical resistivity with increasing substrate temperature was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed the average transmittance over 83% in the visible range.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.33-37
• /
• 2013

In this study, we have investigated the effect of the substrate temperature and hydrogen flow rate on the characteristics of IZO thin films for the organic light emitting diodes (OLED) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering at room temperature and $300^{\circ}C$ with various $H_2$ flow rate. In order to investigate the influences of the oxygen, the flow rate of hydrogen in argon mixing gas has been changed from 0.1sccm to 0.9sccm. IZO thin films deposited at room temperature show amorphous structure, whereas IZO thin films deposited at $300^{\circ}C$ show crystalline structure having an (222) preferential orientation regardless of $H_2$ flow rate. The electrical resistivity of IZO film decreased with increasing flow rate of $H_2$ under Ar+$H_2$. The change of electrical resistivity with increasing flow rate of $H_2$ was mainly interpreted in terms of the charge carrier concentration rather than the charge carrier mobility. The electrical resistivity of the amorphous-IZO films deposited at R.T. was lower than that of the crystalline-IZO thin films deposited at $300^{\circ}C$. The increase of electrical resistivity with increasing substrate temperature was interpreted in terms of the decrease of the charge carrier mobility and the charge carrier concentration. All the films showed the average transmittance over 83% in the visible range.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1438-1439
• /
• 2006

$Ge_{2}Sb_{2}Te_5$(GST) thin film at present is a promising candidate for a phase change random access memory (PCRAM) based on the difference in resistivity between the crystalline and amorphous phase. PCRAM is an easy to manufacture, low cost storage technology with a high storage density. Therefore today several major chip in manufacturers are investigating this data storage technique. Recently, A. Pirovano et al. showed that PCRAM can be safely scaled down to the 65 nm technology node. G. T Jeonget al. suggested that physical limit of PRAM scaling will be around 10 nm node. Etching process of GST thin ra films below 100 nm range becomes more challenging. However, not much information is available in this area. In this work, we report on a parametric study of ICP etching of GST thin films in $Cl_2$/Ar chemistry. The etching characteristics of $Ge_{2}Sb_{2}Te_5$ thin films were investigated using an inductively coupled plasma (ICP) of $Cl_2$/Ar gas mixture. The etch rate of the GST films increased with increasing $Cl_2$ flow rate, source and bias powers, and pressure. The selectivity of GST over the $SiO_2$ films was higher than 10:1. X-ray photoelectron spectroscopy(XPS) was performed to examine the chemical species present in the etched surface of GST thin films. XPS results showed that the etch rate-determining element among the Ge, Sb, and Te was Te in the $Cl_2$/Ar plasma.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.3
• /
• pp.459-466
• /
• 2000

Flow characteristics of turbulent elliptic jets were experimentally investigated using a single-frame PIV system. A sharp-edged elliptic nozzle with aspect ratio(AR) of 2 was tested and the experimental results were compared with those of circular jet having the same equivalent diameter($D_e$). The Reynolds number based on the nozzle exit velocity and nozzle equivalent diameter was about $1{\times}10^4$. The spreading rate along the major and minor axis are different remarkably. The jet half width along the major axis decreases at first and then increases with going downstream. But along the minor axis the jet width increases steadily. The elliptic jet of AR=2 has one switching points at $X/D_e=2$ within the near field. Turbulence properties are also found to be significantly different along the major and minor axis planes.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.620-625
• /
• 2012

A general synthetic method to make $Fe_3O_{4-{\delta}}$ (activated magnetite) is the reduction of $Fe_3O_4$ by $H_2$ atmosphere. However, this process has an explosion risk. Therefore, we studied the process of synthesis of $Fe_3O_{4-{\delta}}$ depending on heat-treatment conditions using $FeC_2O_4{\cdot}2H_2O$ in Ar atmosphere. The thermal decomposition characteristics of $FeC_2O_4{\cdot}2H_2O$ and the ${\delta}$-value of $Fe_3O_{4-{\delta}}$ were analyzed with TG/DTA in Ar atmosphere. ${\beta}-FeC_2O_4{\cdot}2H_2O$ was synthesized by precipitation method using $FeSO_4{\cdot}7H_2O$ and $(NH_4)_2C_2O_4{\cdot}H_2O$. The concentration of the solution was 0.1 M and the equivalent ratio was 1.0. ${\beta}-FeC_2O_4{\cdot}2H_2O$ was decomposed to $H_2O$ and $FeC_2O$4 from $150^{\circ}C$ to $200^{\circ}C$. $FeC_2O4$ was decomposed to CO, $CO_2$, and $Fe_3O_4$ from $200^{\circ}C$ to $250^{\circ}C$. Single phase $Fe_3O_4$ was formed by the decomposition of ${\beta}-FeC_2O_4{\cdot}2H_2O$ in Ar atmosphere. However, $Fe_3C$, Fe and $Fe_4N$ were formed as minor phases when ${\beta}-FeC_2O_4{\cdot}2H_2O$ was decomposed in $N_2$ atmosphere. Then, $Fe_3O_4$ was reduced to $Fe_3O_{4-{\delta}}$ by decomposion of CO. The reduction of $Fe_3O_4$ to $Fe_3O_{4-{\delta}}$ progressed from $320^{\circ}C$ to $400^{\circ}C$; the reaction was exothermic. The degree of exothermal reaction was varied with heat treatment temperature, heating rate, Ar flow rate, and holding time. The ${\delta}$-value of $Fe_3O_{4-{\delta}}$ was greatly influenced by the heat treatment temperature and the heating rate. However, Ar flow rate and holding time had a minor effect on ${\delta}$-value.

• Journal of the Speleological Society of Korea
• /
• no.82
• /
• pp.1-4
• /
• 2007

In this paper, the etching of Au films using photoresist masks on Si substrates was investigated using a capacitively coupled plasma etch reactor. The advantages of plasma etch techniques over current methods for Au metalization include the ability to simplify the metalization process flow with respect to resist lift-off schemes, and the ability to cleanly remove etched material without sidewall redeposition, as is seen in ion milling. The etch properties were measured for different gas mixing ratios of CF4/Ar, and chamber pressures while the other conditions were fixed. According to statistical design of experiment (DOE), etching process of Au films was characterized and also 20 samples were fabricated followed by measuring etch rate, selectivity and etch profile. There is a chemical reaction between CF4 and Au. Au- F is hard to remove from the surface because of its high melting point. The etching products can be sputtered by Ar ion bombardment.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.204-207
• /
• 2003

The present paper reports high-fidelity simulation of direct initiation processes of cylindrical detonation waves by concentrated energy deposition. The goal is to understand the underpinning mechanisms in failed or successful detonation initiation processes. We employed the Space-Time CESE method to solve the reacting flow equations, including realistic finite-rate chemistry model of the nine species and twenty-four reactions for H$_2$-O$_2$-Ar mixtures. Detailed results of sub-critical, critical. and supercritical initiation process are reported.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.286-291
• /
• 2003

(Pb,Sr)TiO$_3$(PST) thin films have attracted great interest as new dielectric materials of capacitors for Gbit dynamic random access memories. In this study, inductively coupled CF$_4$/Ar plasma was used to etch PST thin films. The maximum etch rate of PST thin films was 740 $\AA$/min at a CF$_4$(20 %)/Ar(80 %) 9as mixing ratio, an RF power of 800 W, a DC bias voltage of -200 V, a total gas flow of 20 sccm, and a chamber pressure of 15 mTorr. To clarify the etching mechanism, the residue on the surface of the etched PST thin films was investigated by X-ray photoelectron spectroscopy. It was found that Pb was mainly removed by physically assisted chemical etching. Sputter etching was effective in the etching of Sr than the chemical reaction of F with Sr, while Ti can almost removed by chemical reaction.