• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.1-8
• /
• 2005

Plasma researches using parallel-plate electrodes are widely used in semiconductor application such as etching and thin film deposition. Therefore, a quantitative understanding and control of plasma behavior are becoming increasingly necessary because their important applications and simulation techniques have been actively carried out in order to solve such problems above. In this paper, we developed a two-dimensional(2D) self-consistent fluid model, because 2D models can deal with real reactor geometries. The fluid model is based on particle continuity equations for taking account of an electrode system in a cylindrical geometry. An pure Ar gas was used at 500[mTorr] and radio-frequency (13.56(MHz)). Four models were simulated under the different electrode geometries which have chamber widths of 5.25, 6.0, 8.0, and 10.0[cm] and we compared their results with each other. Plasma uniformity and a do self-bias voltage were also discussed.

• Journal of the Korean Vacuum Society
• /
• v.16 no.2
• /
• pp.110-115
• /
• 2007

A plasma enhanced atomic layer deposition(PEALD) system has been constructed adopting an inductively coupled plasma(ICP) source with an ALD system, and its plasma generation was carried out. Cobalt thin films were deposited on a p-type Si(100) wafer at $230^{\circ}C$. $Co_{2}(CO)_{6}$ was used as a cobalt precursor, $NH_{3}$ as a reactant, and Ar as a carrier and purge gas. The properties of the thin films were investigated using field emission scanning electron microscopy(FESEM) and auger electron spectroscopy(AES). Large amounts of impurities were found in both the ALD film and the PEALD film, however, the amount of impurities in the PEALD film was reduced to about 50 % compared to that in the ALD film. It was found that $NH_{3}$ plasma, very effectively, induces the reaction with carbon in a cobalt precursor.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.47-52
• /
• 2008

As the packing density of IC devices gets ever higher, the thickness of the gate $SiO_2$ layer of the MOS devices is now required to be reduced down to 1 nm. For such a thin $SiO_2$ layer, the MOS device cannot operate properly because of tunneling current and threshold voltage shift. Hence there has been much effort to develop new dielectric materials which have higher dielectric constants than $SiO_2$ and is free from such undesirable effects. In this work, the physical and electrical characteristics of ALD $ZrO_2$ film have been studied. After deposition of a thin ALD $ZrO_2$ film, it went through thermal treatment in the presence of argon gas at $800^{\circ}C$ for 1 hr. The characteristics of morphology, crystallization kinetics, and interfacial layer of $Pt/ZrO_2/Si$ samples have been investigated by using the analyzing instruments like XRD, TEM and C-V plots. It has been found that the characteristics of the $Pt/ZrO_2/Si$ device was enhanced by the thermal treatment.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.80-84
• /
• 2007

Charcoal was used as a carbon source for improving the critical current density of $MgB_2$ and the effect of annealing temperature on the $J_c$ of $MgB_2$ was investigated. The charcoal powder used in this study was $1{\sim}2$ microns in size and was prepared by wet attrition milling. $MgB_2$ bulk samples with a nominal composition of $Mg(B_{0.95}C_{0.05})_2$ were prepared by in situ process of Mg and B powders. The powder mixture was uniaxially compacted into pellets and heat treated at temperatures of $650^{\circ}C\;-\;1000^{\circ}C$ for 30 minutes in flowing Ar gas. It was found that superconducting transition temperature of $Mg(B_{0.95}C_{0.05})_2$ decreased by charcoal additions which indicates the carbon substitution for boron site. $J_c$ of $Mg(B_{0.95}C_{0.05})_2$ was lower than that of the undoped $MgB_2$ at the magnetic fields smaller than 4 Tesla, while it was higher than that of the undoped sample especially at the magnetic field higher than 4 T. High temperature annealing seems to be effective in increasing $J_c$ due to the enhanced carbon diffusion into boron sites.

• Progress in Superconductivity
• /
• v.9 no.1
• /
• pp.96-101
• /
• 2007

[ $YBa_2Cu_3O_{7-{\delta}}$ ] films have been prepared on $LaAlO_3$ (100) single-crystal substrates by a metalorganic deposition using dichloroacetate precursors (DCA-MOD). Calcination conditions were varied in order to optimize the microstructure and the superconducting properties of YBCO film. Coated films were calcined at various temperatures ranging from $400{\sim}700^{\circ}C$ in flowing humid oxygen atmosphere. Ramping rate to calcination tempertures was $2.22^{\circ}C/min$. Conversion heat treatment was performed at $800^{\circ}C$ for 2 h in flowing Ar gas containing 1000 ppm oxygen with a humidity of 9.45%. Observations of surface and cross sectional SEM microstructure showed that the particle size in the calcined film increased in the range of 100-200 nm with heating rate and the calcination temperature. SEM EDS analysis showed that 13 a/o of chlorine was contained in the calcined film. It was also observed that the porosity increased with the heating rate and temperature. Porous microstructure was developed when YBCO films were prepared using porous calcined film. Dense microstructure and high $J_c$ over $1\;MA/cm^2$ was obtained when calcination was carried out at the temperature of $500^{\circ}C$ with a heating rate of $2.22^{\circ}C/min$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.619-619
• /
• 2013

The interfacial state between $Ta_2O_5$ and a Si substrate during the growth of $Ta_2O_5$ films by atomic layer deposition (ALD) was investigated using in-situ synchrotron radiation photoemission spectroscopy (SRPES). A newly synthesized liquid precursor Ta($N^tBu$) $(dmamp)_2Me$ was used as the metal precursor, with Ar as a purging gas and $H_2O$ as the oxidant source. After each half reaction cycle, samples were analyzed using in-situ SRPES under ultrahigh vacuum at room temperature. SRPES analysis revealed that Ta suboxide and Si dioxide were formed at the initial stages of $Ta_2O_5$ growth. However, the Ta suboxide states almostdisappeared as the ALD cycles progressed. Consequently, the $Ta^{5+}$ state, which corresponds with the stoichiometric $Ta_2O_5$, only appeared after 4.0 cycles. Additionally, tantalum silicate was not detected at the interfacial states between $Ta_2O_5$ and Si. The measured valence band offset between $Ta_2O_5$ and the Si substrate was 3.22 eV after 3.0 cycles.

• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.7-18
• /
• 1989

The distinguishing characteristic of the glow discharge is that chemical reaction induced by partially ionized gases are limited only to the substrate surface. Most studies have been done on the plasma etching and polymerization. The graft polymerization in vapour phase by cold plasma has been rarely investigated. In this study the system of tub3ar reaction chamber with capacitively coupled electrode of alternative current of 60 Hz was employed for the graft polymerization. The graft polymerization of Acylic Acid(AA) onto the poly (ethylene terephthalate) (PET) was carried out by treatment of PET film and fabric by cold plasma (glow discharge of argon gas), followed by the supply of AA vapour. The graft yield was about 1 wt%. The surface property was determined by contact angle, the surface tension was evaluated by zisman’s plot and equation of surface tension mesurement. The results were as follows: 1. In order to obtain lower contact angle, it was effective to avoid the vicinity of electrodes for a setting position of substrate. 2. Contact angle affected on the monomer pressure and its duration of exposure to the acid vapour. 3. Polymer radical formation was influenced by the changes of the value of current density and plasma treatment time. 4. Total surface tension of plasma grafted PET film increased. With an increase in the carboxylic acid content, the dispersion force decreased, while, the polar force and hydrogen bonding force increased. 5. The contact angle decreased from $75^\circ$ to around $30^\circ$ by plasma grafting. There was no ageing effect on the contact angle after 4 months.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.2
• /
• pp.1-13
• /
• 2015

The Coupled Model Intercomparison Project Phase 5 (CMIP5), coordinated by the World Climate Research Programme in support of the Intergovernmental Panel on Climate Change (IPCC) AR5, is the most recent, provides projections of future climate change using various global climate models under four major greenhouse gas emission scenarios. There is a wide selection of climate models available to provide projections of future climate change. These provide for a wide range of possible outcomes when trying to inform managers about possible climate changes. Hence, future agrometeorological indicators estimation will be much impacted by which global climate model and climate change scenarios are used. Decision makers are increasingly expected to use climate information, but the uncertainties associated with global climate models pose substantial hurdles for agricultural resources planning. Although it is the most reasonable that quantifying of the future uncertainty using climate change scenarios, preliminary analysis using reasonable factors for selecting a subset for decision making are needed. In order to narrow the projections to a handful of models that could be used in a climate change impact study, we could provide effective information for selecting climate model and scenarios for climate change impact assessment using maximum/minimum temperature, precipitation, reference evapotranspiration, and moisture index of nine Representative Concentration Pathways (RCP) scenarios.

• Journal of Powder Materials
• /
• v.6 no.4
• /
• pp.314-319
• /
• 1999

The solid state reaction by mechanical alloying(MA) generally proceeds by lowering the free energy as the result of a chemical reaction at the interface between the two adjacent layers. However, Lee et $al.^{1-5)}$ reported that a mixture of Cu and Ta, the combination of which is characterized by a positive heat of mixing of +2kJ/mol, could be amorphized by mechanical alloying. This implies that there exists an up-hill process to raise the free energy of a mixture of pure Cu and la to that of an amorphous phase. It is our aim to investigate to what extent the MA is capable of producing a non-equilibrium phase with increasing the heat of mixing. The system chosen was the ternary $Cu_{30}Ta_{ 70-x}Mo_ x$ (x=35, 10). The mechanical alloying was carried out using a Fritsch P-5 planetary mill under Ar gas atmosphere. The MA powders were characterized by the X-ray diffraction with Cu-K $\alpha$ radiation, thermal analysis, electron diffraction and TEM micrographs. In the case of x=35, where pure Cu powders were mixed with equal amount of pure Ta and Mo powders, we revealed the formation of bcc solid solution after 150 h milling but its gradual decomposition by releasing fcc-Cu when milling time exceeded 200 h. However, an amorphous phase was clearly formed when the Mo content was lowered to x=10. It is believed that the amorphization of ternary $Cu_{30}Ta_{60}Mo_{10}$ powders is essentially identical to the solid state amorphization process in binary $Cu_{30}Ta_{70}$ powders.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.533-538
• /
• 2001

The ZnSe sample grown by chemical bath deposition (CBD) method were annealed in Ar gas at 450$^{\circ}C$ Using extrapolation method of X-ray diffraction pattern, it was found to have zinc blend structure whose lattice parameter a$\_$o/ was 5.6687 ${\AA}$. From Hall effect, the mobility was likely to be decreased by impurity scattering at temperature range from 10 K to 150 K and by lattice scattering at temperature range from 150 K to 29 3K. The band gap given by the transmission edge changed from 2.7005 eV at 293 K to 2.8739 eV at 10 K. Comparing photocurrent peak position with transmission edge, we could find that photocurrent peaks due to excition electrons from valence band, $\Gamma$$\_$8/ and $\Gamma$$\_$7/ to conduction band $\Gamma$$\_$6/ were observed at photocurrent spectrum. From the photocurrent spectra by illumination of polarized light on the ZnSe thin film, we have found that values of spin orbit coupling splitting Δso is 0.0981 eV. From the PL spectra at 10 K, the peaks corresponding to free bound excitons and D-A pair and a broad emission band due to SA is identified. The binding energy of the free excitons are determined to be 0.0612 eV and the dissipation energy of the donor -bound exciton and acceptor-bound exciton to be 0.0172 eV, 0.0310 eV, respectively.