• Magazine of the Korean Society of Agricultural Engineers
• /
• v.26 no.1
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.34 no.6
• /
• pp.1731-1741
• /
• 2014

Recently, many overpasses, highway, and advanced transit systems have been constructed to distribute the traffic congestion, thus small size of curved bridges with small curvature such as ramp structures have been increasing. Many of early curved bridges had been constructed by using straight beams with curved slabs, but curved steel beams have replaced them due to the cost, aesthetic and the advantage in building the section form and manipulating the curvature of beams, thereby large portion of curved bridges were applied with steel box girders. However, steel box girder bridges needs comparatively high initial costs and continuous maintenance such as repainting, which is the one of the reason for increasing the cost. Moreover, I-type steel plate girder which is being studied by many researchers recently, seem to have problems in stability due to the low torsional stiffness, resulting from the section characteristics with thin plate used for web and open section forms. Therefore, in recent studies, researchers have proposed curved precast PSC girders with low cost and could secured safety which could replace the curved steel girder type bridges. Hence, this study developed a Smart Mold system to manufacture efficient curved precast PSC girders. And by using this mold system a 40 m 2-girder bridge was constructed for a static flexural test, to evaluate the safety and performance under ultimate load. At the manufacturing stage, each single girder showed problems in the stability due to the torsional moment, but after the girders were connected by cross beams and decks, the bridge successfully distributed the stress, thereby the stability was confirmed. The static loading test results show that the initial crack was observed at 1,400 kN when the design load was 450 kN, and the load at the allowable deflection by code was 1,800 kN, which shows that the safety and usability of the curved precast PSC bridge manufactured by Smart Mold system is secured.

• The korean journal of orthodontics
• /
• v.36 no.6
• /
• pp.412-421
• /
• 2006

Objective: The result of finite element analysis depends on material properties, structural expression, density of element, and boundar or loading conditions. To represent proper elastic behavior, a finite element model was made using Hounsfield unit (HU) values in CT images. Methods: A 13 year 6 month old male was used as the subject. A 3 dimensional visualizing program, Mimics, was used to build a 3D object from the DICOM file which was acquired from the CT images. Model 1 was established by giving 24 material properties according to HU. Model 2 was constructed by the conventional method which provides 2 material properties. Protraction force of 500g was applied at a 45 degree downward angle from Frankfort horizontal (FH) plane. Results: Model 1 showed a more flexible response on the first premolar region which had more forward and downward movement of the maxillary anterior segment. Maxilla was bent on the sagittal plane and frontal plane. Model 2 revealed less movement in all directions. It moved downward on the anterior part and upward on the posterior part, which is clockwise rotation of the maxilla. Conclusion: These results signify that different outcomes of finite element analysis can occur according to the given material properties and it is recommended to use HU values for more accurate results.

• Journal of Korean Society of Forest Science
• /
• v.109 no.3
• /
• pp.259-270
• /
• 2020

Extreme weather events, such as heat and drought, have occurred frequently over the past two decades. This has led to continuous reports of cases of forest damage due to physiological stress, not pest damage. In 2014, pine trees were collectively damaged in the forest genetic resources reserve of Sogwang-ri, Uljin, South Korea. An investigation was launched to determine the causes of the dieback, so that a forest management plan could be prepared to deal with the current dieback, and to prevent future damage. This study aimedto 1) understand the topographic and structural characteristics of the area which experienced pine tree dieback, 2) identify the main causes of the dieback, and 3) predict future risk areas through the use of machine-learning techniques. A model for identifying risk areas was developed using 14 explanatory variables, including location, elevation, slope, and age class. When three machine-learning techniques-Decision Tree, Random Forest (RF), and Support Vector Machine (SVM) were applied to the model, RF and SVM showed higher predictability scores, with accuracies over 93%. Our analysis of the variable set showed that the topographical areas most vulnerable to pine dieback were those with high altitudes, high daily solar radiation, and limited water availability. We also found that, when it came to forest stand characteristics, pine trees with high vertical stand densities (5-15 m high) and higher age classes experienced a higher risk of dieback. The RF and SVM models predicted that 9.5% or 115 ha of the Geumgang Pine Forest are at high risk for pine dieback. Our study suggests the need for further investigation into the vulnerable areas of the Geumgang Pine Forest, and also for climate change adaptive forest management steps to protect those areas which remain undamaged.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.4
• /
• pp.188-198
• /
• 2016

In soybeans, responses of high temperature according to shift of sowing dates during the growing season was explored using the crop model, CROPGRO-soybean. In addition, it analyzed impact on change of sowing dates affects yield potential of soybean under future climate scenario (2041-2070). In Jeonju and Miryang during 1981-2010, if sowing at 15 or ten days ahead from 10 June, namely in shorten of the sowing day (i.e. when sown on 25 or 30 May), the yield potential reduced. However, the yield potential increased when sown 5 June. In the case of delay of sowing day (i.e. when sown on 15 or 20 June), reduction of yield potential in the average -5% was higher than increase in the average +2%. In particular, the relative changes for shorten of the sowing day or delay of the sowing day do not be shown in normal years which high temperatures did not abnormally occur during the growing season from 2003 to 2010 except when sown on 25 May. In abnormal years which high temperatures occurred during the critical period, especially R5 to R7, shorten of the sowing day affected to the increase of yield potential in Miryang, while the yield potential decreased in Jeonju except when sown on 5 June. However, delay of the sowing day influenced on the reduction of yield potential both in two sites. In future climate scenario of Representative Concentration Pathway (RCP) 8.5 during from 2041 to 2070, the increase and decrease of yield potential for shorten of the sowing day were +10/-9% for RCP 8.5 of Jeonju, and +14/-9% for RCP 8.5 of Miryang, respectively. Additionally, it showed +10/-17% for RCP 8.5 in Jeonju, and +10/-29% for RCP 8.5 in Miryang, respectively in the increase and decrease of yield potential for delay of the sowing day.

• Restorative Dentistry and Endodontics
• /
• v.32 no.3
• /
• pp.222-235
• /
• 2007

The objectives of this study was to evaluate the effect of thermocycling on the ${\mu}TBS$ (microtensile bond strength) to dentin with four different adhesive systems to examine the bonding durability. Freshly extracted $3^{rd}$ molar teeth were exposed occlusal dentin surfaces, and randomly distributed into 8 adhesive groups 3-steps total-etching (Scotchbond Multi-Purpose Plus; SM, All Bond-2; AB), 2-steps total-etching (Single Bond; SB, One Step plus; OS), 2-steps self-etching (Clearfil SE Bond; SE, AdheSE AD) and single-step self-etching systems (Promp L-Pop; PL, Xeno III; XE) Each adhesive system in 8 adhesives groups was applied on prepared dentin surface as an instruction and resin composite (Z250) was placed incrementally and light-cured. The bonded specimens were sectioned with low-speed diamond saw to obtain $1\times1mm$ sticks after 24 hours of storage at $37^{\circ}C$ distilled water and proceeded thermocycling at the pre-determined cycles of 0, 1,000 and 2,000. The ${\mu}TBS$ test was carried out with EZ-tester at 1mm/min. The results of bond strength test were statistically analyzed using one-way ANOVA/ Duncan's test at the a < 0.05 confidence level. Also, the fracture mode of debonded surface and the interface were examined under SEM. The results of this study were as follows ; 1. 3-step total etching adhesives showed stable, but bond strength of 2-step adhesives were decreased as thermocycling stress. 2. SE showed the highest bond strength, but single step adhesives (PL, XE) had the lowest value both before and after thermocycling. 3 Most of adhesives showed adhesive failure. The total-etching systems were prone to adhesive failure and the single-step systems were mixed failure after thermocycling. Within limited results of this study, the bond strength of adhesive system was material specific and the bonding durability was affected by the bonding step/ procedure of adhesive Simplified bonding procedures do not necessarily imply improved bonding performance.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.64 no.4
• /
• pp.406-413
• /
• 2019

The purpose of this research was to analyze the effect of different sowing times on the flowering and maturing of major soybean cultivars by varying day length and temperature in the central plain region. The average of growth period and cumulative temperature in five test cultivars by sowing times were 121 days and 2,972℃ on June 1, respectively and gradually decreased to 85 days, 2,042℃, respectively on July 20. Analysis of the flowering response according to the sowing times showed that flowering was greatly influenced by the decrease of photoperiod until the sowing on July 10, and the minimum number of days for flowering were 27 days, 36 days, respectively in early and mid-rate maturing type in the central plain region. Daepung 2 is classified to the same ecotype with Daewonkong, the total number of growing days was not different between two cultivars, but ripening period (R2-R6) was longer by 5 days and yield was higher by 11% in Daepung 2. The maturity rate was also high and safe enough to maintain more than 90% through the entire sowing times. This ecological characteristic can be usefully applied as a section index for breeding environmental stress resistant and high yielding soybean varieties. The yield of 4 domestic cultivars (except TI196944) sowing on July 20 were 85~92% levels compared to sowing on June 20.

• Journal of Life Science
• /
• v.23 no.2
• /
• pp.167-174
• /
• 2013

Peroxiredoxin 6 (Prx 6) is a member of the thiol-specific antioxidant protein family, which may play a role in protection against oxidative stress and in regulating phospholipid turnover. The aim of this study was to determine whether a human Prx 6/Luc vector was stably expressed and responded to antioxidants in a lung cell line (NCI-H460). To achieve this, the luciferase signal, hPrx 6 mRNA expression, and superoxide dismutase (SOD) activity were measured in transfectants with a hPrx 6/Luc plasmid after treatment with four antioxidant extracts, including Korea white ginseng (KWG), Korea red ginseng (KRG), Liriope platyphylla (LP), and red Liriope platyphylla (RLP). First, the hPrx 6/Luc plasmid was successfully constructed with DNA fragments of human Prx 6 promoter, amplified by PCR using genomic DNA isolated from NCI-H460 cells, and cloned into the pTransLucent reporter vector. The orientation and sequencing of the hPrx 6/Luc plasmid were identified with restriction enzyme and automatic sequencing. A luciferase assay revealed significant enhancement of luciferase activity in the four treatment groups compared with a vehicle-treated group, although the ratio of the increase was different within each group. The KRG- and LP-treated groups showed higher activity than the KWG- and RLP-treated groups. Furthermore, the luciferase activity against RLP occurred roughly in a dose-dependent manner. However, the level of endogenous hPrx 6 mRNA did not change in any group treated with the four extracts. The SOD activity was in agreement with the luciferase activity. Therefore, these results indicate that the hPrx 6/Luc vector system may successfully express and respond to antioxidant compounds in NCI-H460 cells. The data also suggest that the Prx 6/Luc vector system may be effectively applied in screening the response of hPrx 6 to antioxidant compounds in transgenic mice.

• Women's Health Nursing
• /
• v.4 no.1
• /
• pp.161-178
• /
• 1998

In spite of the great progress of the theory and skill of the Nursing Care & Medical area in relation to pregnancy, nurses in clinics face up to many challenges in maternity nursing care areas. The reason is that the mobility and mortality of mothers was sharply decreased and the unknown high-risk diseases of pregnancy woman in the past is made public. That's why it is difficult to meet the pregnancy woman in natural process from pregnancy to delivery in recently. Admission rooms are filled with high-risk pregnancy women. As a matter of fact, we have done nursing care into the surface symptoms and diseases of high-risk pregnancy women so far. We have been indifferent to a long period hospitalization, separation from family, and conflict of repeated examination. Therefore, it is widely spread to understand the emotional conflict experienced by high-risk pregnancy women and to need for nursing intervention to bring up about emotional support and the ability of perception in psychological crisis. Although the pregnancy woman judged in high-risk should carry out normal task of pregnancy, she have to be confronted with secondary risk situation. The health of self & fetus threatened by the risk situation could be decreased through care plan, but psychological stress increases. Therefore, the pregnancy brings into non-control state. It is important to ask that what the hospitalized pregnancy women in high-risk think of themselves status. Because misunderstanding or serious anxiety of themselves status put into mother and fetus in danger. And adaptation mode makes all the difference. I would like to consider how nurses could deal with this high-risk circumstances in the position of pregnancy woman on the basis of the above fact. This study uses phenomenological method to suggest the basis material for nurses to do nursing intervention in view of pregnancy woman. Because this method understands the nature of true life of pregnancy woman throughly. The phenomenological method is the sources to describe or explain affluently the process generated in confirmation areas and environment and is the application for readers to understand and recognize clinic reality and then apply this method to reasoning study place or other places. Specifically, the phenomenon study method, one of the phenomenological method, is applied. The use of that method is to describe and generalize the experience in environment exactly. The study of this study is as follows : Among 187 descriptive stamens from 8 study participants are classified into 42 theme cluster at the stage of the first analysis. Those theme is categorized into 8 sub-subjects such as anxiety of uncertainty, foreknowledge about risk circumstance, will power about overcome, unsettled feeling about hospital, relief, optimistic thought, family support, and indifferences. At the last stage of analysis, those things are categorized into 3 subjects. When high-risk pregnancy woman foretell the situation, they feel unsettlement about uncertainty and untrust feeling about hospital. But they are ease with family support and hospital support. On the other hand, they express indifferent 3-way structure response to the situation having will of overcome and exceeding optimistic thought. In those statements, the experience by pregnancy woman shows 3 respect subjects. 1. They are anxious of this situation and are in desperation and don't recognize their role to be carried out 2. They think of this situation as normal process of pregnancy and are not concerned that this can give themselves and fetus fatal damage. 3. The pregnancy women will never confront this situation. This study shows the pregnancy woman has anxiety and optimistic relief about the situation, and ignores and optimistic relief about the situation, and ignores many things. Therefore, nurses in clinic should give pregnancy woman knowledge and information about the high-risk and help them to deal with the situation spontaneously. High-risk pregnancy woman should have the care plan in respect of the right perception. And the nurse know that their support help out pregnancy woman overcome the crisis in this respect of the special nursing intervention.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.41 no.4
• /
• pp.315-324
• /
• 2015

In this study, we prepared liquid crystal emulsion composed of amphiphilic substance $C_{14-22}$ alcohol, $C_{12-20}$ alkyl glucoside, behenyl alcohol and studied liquid crystal emulsion of properties and in vitro skin permeation. The results of formulation experiments, the clear liquid crystalline structure was observed in the ratio of $C_{14-22}$ alcohol 0.8%, $C_{12-20}$ alkyl glucoside 3.2%, behenyl alcohol 4% in the formulation. The results of physical property measurements, the viscosity of liquid crystal emulsion and O/W emulsion applied as a control group was respectively $1871.26{\sim}1.15Pa{\cdot}s$, $1768.69{\sim}1.14Pa{\cdot}s$ and the shear stress of O/W emulsion was 178.68 ~ 909.18 Pa, that of liquid crystal emulsion was 190.45 ~ 919.38 Pa. The storage modulus of O/W emulsion was 3428.53 ~ 9157.45 Pa, that of liquid crystal emulsion was 4487.82 ~ 8195.59 Pa. The tan (delta) value of O/W emulsion which means a ratio of viscosity to elasticity was 0.43 ~ 0.19, and that of liquid crystal emulsion was 0.23 ~ 0.25. The water content value on the skin for liquid crystal emulsion was significantly higher from 1 h to 6 h compared with that of O/W emulsion and the transepidermal water loss on the skin was significantly superior in skin moisture loss suppression from 30 min to 4 h compared with that of O/W emulsion. The results of skin permeation using glycyrrhizic acid, the result of skin permeation amount of liquid crystal emulsion for 24 h was $64.58{\mu}g/cm^2$, that of O/W emulsion was $37.07{\mu}g/cm^2$, that of butylene glycol solution was $41.05{\mu}g/cm^2$. Hourly permeability results, it is showed that skin penetration effect of the liquid crystal emulsion increases after 8 h. These results suggest that liquid crystal emulsions are effective for skin moisturizing effect and function as potential efficacy ingredient delivery system for the transdermal delivery.