• 한국도로학회논문집
• /
• 제19권6호
• /
• pp.37-46
• /
• 2017

PURPOSES : A composite pavement utilizes both an asphalt surface and a concrete base. Typically, a concrete base layer provides structural capacity, while an asphalt surface layer provides smoothness and riding quality. This pavement type can be used in conjunction with rollercompacted concrete (RCC) pavement as a base layer due to its fast construction, economic efficiency, and structural performance. However, the service life and functionality of composite pavement may be reduced due to interfacial bond failure. Therefore, adequate interfacial bonding between the asphalt surface and the concrete base is essential to achieving monolithic behavior. The purpose of this study is to investigate the bond characteristics at the interface between asphalt (HMA; hot-mixed asphalt) and the RCC base. METHODS : This study was performed to determine the optimal type and application rate of tack coat material for RCC-base composite pavement. In addition, the core size effect, temperature condition, and bonding failure shape were analyzed to investigate the bonding characteristics at the interface between the RCC base and HMA surface. To evaluate the bond strength, a pull-off test was performed using different diameters of specimens such as 50 mm and 100 mm. Tack coat materials such as RSC-4 and BD-Coat were applied in amounts of 0.3, 0.5, 0.7, 0.9, and $1.1l/m^2$ to determine the optimal application rate. In order to evaluate the bond strength characteristics with temperature changes, a pull-off test was carried out at -15, 0, 20, and $40^{\circ}C$. In addition, the bond failure shapes were analyzed using an image analysis program after the pull-off tests were completed. RESULTS : The test results indicated that the optimal application rate of RSC-4 and BD-Coat were $0.8l/m^2$, $0.9l/m^2$, respectively. The core size effect was determined to be negligible because the bond strengths were similar in specimens with diameters of 50 mm and 100 mm. The bond strengths of RSC-4 and BD-Coat were found to decrease significantly when the temperature increased. As a result of the bonding failure shape in low-temperature conditions such as -15, 0, and $20^{\circ}C$, it was found that most of the debonding occurred at the interface between the tack coat and RCC surface. On the other hand, the interface between the HMA and tack coat was weaker than that between the tack coat and RCC at a high temperature of $40^{\circ}C$. CONCLUSIONS : This study suggested an optimal application rate of tack coat materials to apply to RCC-base composite pavement. The bond strengths at high temperatures were significantly lower than the required bond (tensile) strength of 0.4 MPa. It was known that the temperature was a critical factor affecting the bond strength at the interface of the RCC-base composite pavement.

• 대한간호학회지
• /
• 제21권3호
• /
• pp.349-364
• /
• 1991

Recognition of the usefulness and the importance of the nursing diagnosis is increasing. There is a prevailing opinion that nursing diagnosis should be used to improve the quality of nursing care. Developing standardized nursing care palns based on nursing diagnoses is therefore considered one of the most essential projects for professional growth and improvement in the nursing world of Korea. Consequently, in the first stage of this research project, the ten nursing diagnses used most frequently with patients on medical and surgical wards were determined and related nursing care plans were developed, implemented and evaluated. The application of the standardized nursing care plans raised the nurses' confidence and proved to be effective in enhancing the quality of nursing care. This study was initiated as the next stage, to develop, test, and determine the validity of nursing care plans for the remaining nursing diagnoses. Nineteen medical and surgical wards were selected for the study ; the 176 staff nurses working on those wards and 1211 patients hospitalized there (603 patients during the nursing care plan use) took part in the project. The following summarizes the results of the study : 1. After listing all the nursing diagnoses up to the 20th in frequency from each ward except the ten used in the first study, 22 nursing diagnoses were selected. Two related to ‘self care deficit’, were combined into one. Standardized nursing care plans were established for these 21 nursing diagnoses. 2. The first page of each nursing care plan lists the related factors and defining characteristics as supporting data. The application rate distribution revealed that the majority were recorded less than 50% of the time. For each nursing diagnosis, only one to three related factors were recorded more than 50% of the time regardless of the number of suggested related factors, and similarly, only one to five defining characteristics were recorded more than 50% of the time regardless of the number of suggested defining characteristics. Therefore, these factors and defining characteristics were proposed as the common related factors and the typical signs and symptoms for each nursing diagnosis. 3. The application rate distribution for the expected outcomes, and the nursing orders that were the main data of each nursing care plan occurred more than 50% of the time, unlike the related factors and the characteristics that occurred less frequently. These findings supported the clinical validity. 4. In an effort to evaluate indirectly the effect of the use of the standardized nursing care plans, nurses' job satisfaction and perceptions of their ability in the use of the nursing process were measured and compared. Scores after the use of the plans were significantly higher than those before. The experience in actually using the standardized nursing care plans with patients increased the nurses' professional and emotional satisfaction and their confidence in using the nursing process. Also when the nurses who actually used the nursing care plans were asked to rate their effectiveness, the highest score was given to ‘the ease of establishing the nursing goal’, followed by ‘improved professional advice and care for patients’, ‘the efficiency and systemization of charting’, ‘the definite recognition of the nursing problem’, and ‘the selection of effective and appropriate nursing interventions’ in descending order. The results indicate the nurses were very positive about the effect of the real clinical application of standardized nursing care plans, and that the objective of this study to utilize the nursing diagnosis to strengthen the nursing process was attained.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.548-552
• /
• 2003

In the braking system, the friction force is the most important factor of the design. For long time, many researchers have been strived for getting the exact friction coefficients. But the friction coefficients are affected by the road condition and changed by lots of parameters, such as normal force and characteristics between two contacted materials, temperature, etc. For the development of ABS of the aircraft, HILS(Hardware-In-the-Loop-Simulation) test and dynamometer test was carried out. For the calculation of the friction coefficients, the wheel moments were measured using the load cell mounted on the housing of the wheel. The test conditions were dry and greasy, as the 0.7 and 0.4 in friction coefficient, respectively. In this paper, the test results of the friction coefficients were represented and the improvement method was suggested.

• Journal of the Korean Data and Information Science Society
• /
• 제19권3호
• /
• pp.735-749
• /
• 2008

This article suggests application of logit model for analysis of multicategory responses. Referring to the reference category, characteristic of each category is obtained from analysis of polytomous logit model. With National Pension data it is illustrated that application of logit model helps it possible to find significant factors which may not be found only with polytomous logit model. Application of the logit model is done by reducing the number of categories. Categories are grouped into the former and the latter group according to reference category. Extra finding of significant factor was possible from logistic regression analysis for the two groups after removing the reference category. It is expected that this application would be helpful for finding information and characteristics on ordered multicategory responses where the proportional odds model does not fit.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.988-992
• /
• 2002

Ultrasonic machining technology has been developed over recent years for the manufacture of and quality-assured precision parts for several industrial application such as optics, semiconductors, aerospace, and automobile application. The past decade has seen a tremendous in the use of ceramics in structural application. The excellent thermal, chemical and wear resistance of these material can be realized because of recent improvements in the overall strength and uniformity of advanced ceramics. Ultrasonic machining, in which abrasive particles in slurry with water are presented to the work surface in the presence of an ultrasonic-vibrating tool, is process which should be of considerable interest, as its potential is not limited by the electrical or chemical characteristics of the work material, making it suitable for application to ceramics. This paper intends to further the understanding of the basic mechanism of ultrasonic machining for brittle material and ultrasonic machining of ceramics based in the fracture-mechanic concept has been analyzed.

• Journal of Electrical Engineering and Technology
• /
• 제8권5호
• /
• pp.984-990
• /
• 2013

This paper develops a new Intelligent Electronic Device (IED), and then presents an application method of a monthly load forecasting algorithm on the smart IEDs. A Multiple Linear Regression (MLR) model implemented with Recursive Least Square (RLS) estimation is established in the algorithm. Case Study proves the accuracy and reliability of this algorithm and demonstrates the practical meanings through designed screens. The application method shows the general way to make use of IED's smart characteristics and thereby reveals a broad prospect of smart function realization in application.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권2호
• /
• pp.330-335
• /
• 2008

In this study, highly miniaturized short-wavelength transmission line employing periodically perforated ground metal (PPGM) structures were developed for application to miniaturized on-chip passive component on Si RFIC. The transmission line employing PPGM structure showed shorter wavelength and lower characteristic impedance than conventional coplanar-type transmission line. The wavelength of the transmission line employing PPGM structure was 57% of the conventional coplanar-type transmission line on Si Radio Frequency Integrated Circuit (RFIC) substrate. Basic characteristics of the transmission line employing PPGM structure were also investigated in order to evaluate its suitability for application to a development of miniaturized passive on-chip components. According to the results, it was found that the PPGM structure is a promising candidate for application to a development of miniaturized on-chip passive components on Si RFIC.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권1호
• /
• pp.23-29
• /
• 2003

Stencil is used normally as a mask for solder pasting on pad of a printed circuit board (PCB). The objective of this study is to develop a stencil cutting system and determine the optimal conditions to make good-quality stencil by using a Nd:YAG laser. The effects of process parameters such as laser power, type of mask, gas pressure, cutting speed and pulse duration on the cut edge quality were investigated. In order to analyze the cut surface characteristics (roughness, kerfwidth, dross) optical microscopy, SEM microscopy and roughness measurements were used. As a result, the optimal conditions of cutting process parameters were determined, and the practical feasibility of the proposed system was also examined by using a commercial Gerber file for PCB stencil manufacturing.

• International Journal of Contents
• /
• 제9권4호
• /
• pp.92-101
• /
• 2013

Chinese auspicious element is a kind of art which is used to express yearning of a happy life. It is one of the great treasures of China, with not only emotional value of the people but also an aesthetic value. Chinese auspicious element derives from the aspiration of luck, enthusiasm of life and conciseness of eliminating malicious. It is of great cultural connotation and widely used in interior design, graphic design, fashion design and such. There are many research papers on application methodology of auspicious elements; however, there are very limited research papers on three-dimension product, let alone application in tableware. This paper focuses on illustration of Chinese representative auspicious element "auspicious fish" in tableware design. The research of its application of auspicious element's styling characteristics is of important significance in auspicious element spread and tableware design. This dissertation aims to provide referential design methodology and experience for later researches on related topic.

• 한국CDE학회논문집
• /
• 제17권5호
• /
• pp.342-352
• /
• 2012

As a futuristic construction model, building information model (BIM) based project management system (PMIS) and mobile BIM simulator apps have been showing visible sign. However, researches on the BIM based 3D simulator using mobile device are hard to find result from limitation of mobile device (slow speed at huge 3D file, display size, and etc.) and undefined standard of business processes. Therefore, this research aims at studying application of mobile BIM apps based on cloud computing. Total 8 BIM cloud apps were selected and analyzed in the 5 application feasibility characteristics (speed, view, inquiry, markup, and usability). This research would be essential phase to construct BIM based mobile project management system using cloud computing in the future.