• 한국표면공학회지
• /
• 제35권3호
• /
• pp.149-157
• /
• 2002

Spectral emissivity depends on the surface conditions of the materials. The mechanisms that affect the spectral emissivity in anodic oxide films on aluminum were investigated. The aluminum specimens were anodized in a sulfuric acid solution and the thickness of the resulting oxide film formed changed with the anodizing time. FT-IR spectrum analysis identified the anodic oxide film as boehmite ($Al_2$$O_3$.$H_2$O). Both the infrared emisivity and reflectivity of the anodized aluminum were affected by the structure of the anodic oxide film because Al-OH and Al-O-Al have a pronounced absorption band in the infrared region of the spectrum. The presence of an anodic oxide film on aluminum caused a rapid drop in the infrared reflectivity. An aluminum surface in the clean state had an emissivity of approximately 0.2. However, the infrared emissivity rapidly increased to 0.91 as the thickness of the anodic oxide film increased.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.382-383
• /
• 2007

PMMA plate with nano-sized pattern was synthesized on anodized aluminum oxide template by bluk polymerization method. Anodized aluminum oxide was used as a template to synthesize the PMMA plate with nano-sized pattern. The polymerization of MMA was performed at $75-79^{\circ}C$. It is verified from SPM results that the nano-sized pattern on synthesized PMMA plate was well transferred from that of anodized aluminum oxide template.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1169-1173
• /
• 2015

This paper presents vertical carbon nanotube (CNT) field effect transistors (FETs). For the first time, the author successfully fabricated vertical CNT-based FETs on an anodized aluminum oxide (AAO) template by using atomic layer deposition (ALD). Single walled CNTs were vertically grown and aligned with the vertical pores of an AAO template. By using ALD, a gate oxide material (Al₂O₃) and a gate metal (Au) were centrally located inside each pore, allowing the vertical CNTs grown in the pores to be individually gated. Characterizations of the gated/vertical CNTs were carried and the successful gate integration with the CNTs was confirmed.

• 한국자기학회지
• /
• 제17권2호
• /
• pp.90-94
• /
• 2007

유연하고 얇은 0.025 mm와 0.2 mm의 두께를 지닌 알루미늄 포일을 사용하여 다공성 알루미나 막을 제작하였다. 알루미늄 포일들은 에탄올/과염소산 용액에서 전해연마하여 표면처리를 하였으며, 0.3 M의 옥살산 용액 안에서 양극산화 시켰다. 양극산학 시용액의 온도는 $9^{\circ}C$로 유지시켰으며, 전극에 가해주는 전압을 0.4와 40 V 사이에서 변화시킨 후, 형성된 알루미나 막의 표면을 주사전자현미경으로 관찰하였다. 관찰 결과, 장시간의 양극 산화 시 사용되는 전압의 크기가 1 V 이상일 경우 강한 전기분해 반응으로 인해 생성된 산화막 표면이 파괴되어 있음을 확인할 수 있었다. 반면 1 V 이하로 처리할 경우, 장시간에 걸쳐 안정적으로 양극산화시킬 수 있음을 알 수 있었다. 이 실험을 통해 얇은 알루미늄 포일의 경우 두꺼운 알루미늄 판과 달리 장시간의 양극산화를 통해 다공성 알루미나 막을 형성하기 위해선 1 V 이하의 낮은 전압이 요구되는 것을 확인할 수 있었다.

• 한국표면공학회지
• /
• 제52권5호
• /
• pp.275-281
• /
• 2019

Anodization is widely used to enhance the properties of aluminum, such as hardness, electric resistance, abrasion resistance, corrosion resistance etc. But these properties can be enhanced with additional process. According to the partial crystallization of oxide layer with post heat treatment, enhanced hardness can be expected with partial crystallization. In this study, post heat treatments were applied to the anodized aluminum alloys of Al6061 to achieve the partial crystallization, and crystallizations were evaluated with the reduced breakdown voltages. Interestingly, remarkable enhanced hardness (21~29%), abrasion resistance (26~62%), and reduced breakdown voltage (24~44%) were observed for the sulfuric acid anodized samples when we annealed the anodized samples with 1hour post heat treatment at $360^{\circ}C$. For the Al5052 alloys, a lot of cracks were observed when we applied the post heat treatment.

• 한국표면공학회지
• /
• 제51권6호
• /
• pp.372-380
• /
• 2018

Anodization techniques are widely used in the area of surface treatment of aluminum alloys because of its simplicity, low-cost and good corrosion resistance. In this study, we investigated the relationship between the properties (porosity and thickness) of anodic aluminum oxide (AAO) and its corrosion behavior. Aluminum 5052 alloy was anodized in 0.3 M oxalic acid at $0^{\circ}C$. The anodizing of aluminum 5052 was performed at 20 V, 40 V and 60 V for various durations. The corrosion behavior was studied in 3.5 wt % NaCl using potentiodynamic polarization method. Results showed that the pore diameter and thickness increased as voltage and anodization time increased. The relatively thick oxide film revealed a lower corrosion current density and a higher corrosion potential value.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2005년도 춘계학술발표대회 및 제8회 신소재 심포지엄 논문개요집
• /
• pp.101-101
• /
• 2005

• 제어로봇시스템학회논문지
• /
• 제14권5호
• /
• pp.420-425
• /
• 2008

PMMA light guiding plate with nano-sized pattern was fabricated using anodized aluminum oxide membrane as a template for nano imprint lithography. Nano-sized pore arrays were prepared by the self-organization processes of the anodic oxidation using the aluminum plate with 99.999% purity. Since the aluminum plate has a rough surface, the aluminum plate with thickness of 1mm was anodized after the pre-treatments of chemical polishing, and electrochemical polishing. The surface morphology of the alumina obtained by the first anodization process was controlled by the concentration of electrochemical solution during the first anodization. The surface morphology of the alumina was also changed according to temperature of the solution during chemical polishing performed after first anodization. The pore widening process was employed for obtaining the one-channel with flat surface and height of the channel because the pores of the alumina membrane prepared by the fixed voltage method shows the structure of two-channel with rough surface. It is shown from SPM results that the nano-sized pattern on PMMA light guiding plate fabricated by nano imprint lithography method was well transferred from that of anodized aluminum oxide template.

• 한국재료학회지
• /
• 제31권3호
• /
• pp.122-131
• /
• 2021

In the fabrication of joined materials between anodized aluminum alloy and polymer, the performance of the metal-polymer joining is greatly influenced by the chemical properties of the oxide film. In a previous study, the dependence of physical joining strength on the thickness, structure, pore formation, and surface roughness of films formed on aluminum alloys is investigated. In this study, we investigated the effect of silane coupling treatment on the joining strength and sealing performance between aluminum alloy and polymer. After a two-step anodization process with additional treatment by silane, the oxide film with chemically modified nanostructure is strongly bonded to the polymer through physical and chemical reactions. More specifically, after the two-step anodization with silane treatment, the oxide film has a three-dimensional (3D) nanostructure and the silane components are present in combination with hydroxyl groups up to a depth of 150 nm. Accordingly, the joining strength between the polymer and aluminum alloy increases from 29 to 35 MPa, and the helium leak performance increases from 10-2-10-4 to 10-8-10-9 Pa ㎥ s-1.

• 한국재료학회지
• /
• 제11권4호
• /
• pp.329-334
• /
• 2001

붕산용액에서 양극산화법으로 장벽형 산화피막을 형성시킨 후 미세조직을 관찰하였다. 양극산화시 인가되는 전압에 따른 피막의 성장속도는 1.54nm/v의 직선적인 관계를 나타냈으며 300v의 인가전압에서 생성된 산화피막의 조직은 50$0^{\circ}C$에서 열처리하였을 경우 피막의 상 전이가 일어나지 않았으나 높은 인가전압에서 생성된 산화피막의 경우는 피막의 조직이 비정질에서 ${\gamma}$-alumina로 변태되는 것이 관찰되었다. 또한 피막이 전자빔 조사에 의해서도 ${\gamma}$-alumina로 전이가 일어났다.